• Tribology and Lubricants
• /
• v.28 no.5
• /
• pp.197-202
• /
• 2012

In this study, with the purpose of fundamentally improving the unbalance response vibration of a large PRT motor-generator rotor by design, a performance improvement design analysis is carried-out by retrofitting tilting pad bearings, replacing the plain partial journal bearings that were originally applied for operation at a rated speed of 1,800 rpm. In this process, a goal of the design analysis is to obtain a design solution for maximizing the direct stiffness of the bearings while satisfying the key basic lubrication performance requirements such as the minimum lift-off speed and maximum oil-film temperature. The results show that with a careful design application of tilting pad journal bearings for operation at such a relatively low speed of 1,800 rpm, direct stiffness increment of the bearings by about two times can be effectively achieved. Prevention of pad unloading is also considered in the analysis. Moreover, the designs of elliptical and offset half journal bearings are also analyzed and reviewed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.8
• /
• pp.941-949
• /
• 2011

When a railway vehicle passes through curves & transitions, the running speed must be improved by setting limits on the maximum running speed in each section of the conventional line(Dongdaegoo-Namsunghyun) considering derailment safety. Our goal is to improve the maximum running speed of railway vehicle that passes through curves & transitions where there is a high risk of derailment. We examined the influence on the derailment safety when the railway vehicle passes through curves of actual track conditions (Dongdaegoo-Namsunghyun up and down lines). We performed the derailment safety analysis by increasing the running speed on curve radius by 5%.20% compared to existing speed under actual track conditions.

• Journal of Navigation and Port Research
• /
• v.35 no.7
• /
• pp.605-611
• /
• 2011

In this paper, practical problems for current feeder service between Busan port and west coast of Japan were extracted through in depth interviews with Japanese feeder vessel companies, shippers, and port authority based upon which major criteria (elements) for improvement of the feeder network are structured in hierarchic order and weighed relative importance through AHP method. From the questionnaire answered by Korean and Japanese port users and experts the weights of criteria were calculated and the shipping service was ranked the first by both parties with 0.235 and 0.217, respectively. The port service and support system ranked the second and the third, whereas the port marketing was shown to be the lowest of all. Considering the overall weights, the increase in a port loading and unloading speed of port service was followed by provision of dedicated deck for feeder vessel of port facilities for Korean respondents. Therefore, speed up of the port operations and providing docks for feeder vessel are to be firstly provided for more efficient feeder operations, which would be the basis for the construction of optimal transportation network.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.6
• /
• pp.461-468
• /
• 2002

Computer simulation is essential to design the suspension elements of railway vehicle. By computer simulation, engineers can assess the feasibility of the given design factors and change them to get a better design. But if one wishes to perform complex analysis on the simulation, such as railway vehicle dynamic, the computational time can become overwhelming. Therefore, many researchers have used a surrogate model that has a regression model performed on a data sampling of the simulation. In general, metamodels(surrogate model) take the form y($\chi$)＝f($\chi$)＋$\varepsilon$, where y($\chi$) is the true output, f($\chi$) is the metamodel output, and is the error. In this paper, a second order polynomial equation is used as the RSM(response surface model) for high speed train that have twenty-nine design variables and forty-six responses. After the RSM is constructed, multi-objective optimal solutions are achieved by using a nonlinear programming method called VMM(variable matric method) This paper shows that the RSM is a very efficient model to solve the complex optimization problem.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.1
• /
• pp.95-102
• /
• 2018

This paper proposes a dual lifting and its cooperative control system with two different kinds of floating cranes. The Mega-erection and Giga-erection in the ship building are used to handle heavier and wider blocks and modules as ships and off-shore platforms are enlarged. However, there is no equipment to handle such Tera-blocks. In order to overcome the limit on performance of existing floating cranes, the dual lifting is proposed in this research. In the dual lifting, two floating cranes are well-coordinated to add up the lift capabilities of both cranes without any loss such that virtually a single crane is lifting, maneuvering and unloading. Two main constraints for the dual lifting are as follows: First, two barges of floating cranes should be constrained as a rigid body not to cause a relative motion between two barges and main hooks of the two cranes should be controlled as main hooks of a single crane. In order words, it is necessary to develop the cooperative control of two floating cranes in order to sustain a center of gravity of the module and minimize the tilting angle during the lifting and unloading by the two floating cranes. Two floating cranes are handled as a master-slave system. The master crane is able to gather information about all working conditions and make a decision to control the individual hook speed, which communicates the slave crane by TCP/IP. The developed control system has been embedded in the real floating crane systems and the dual lifting has been demonstrated five times at SHI shipyard in 2015. The moving angles of the lifting module are analyzed and verified to be suitable for hoisting control. It is verified that the dual lifting can be applied for many heavier and wider blocks and modules to shorten the construction time of ships and off-shore platforms.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.5
• /
• pp.958-965
• /
• 2007

The spreaders on container cranes are usually controlled to stop at the same time as their trolleys are stopped. Despite the use of adequate control systems, however, the spreaders usually have comparatively large sway movements, due to their suspension from the trolleys through cables. It is, therefore, important to accurately measure the attitudes of the spreaders, in order to suppress such sways by means of secondary control. Until now, most of conventional anti sway control systems focus on the direct control of the movements of trolleys. which seems not suitable to speed up the entire process - loading and unloading of containers. In this paper, we suggest a new anti sway control system: By using extra equipments - two propellers to suppress the sway and a PSD camera to measure the spreader's attitude - installed on the spreader and the trolley. the sway of the suspended load j, considerably suppressed. The effectiveness of the proposed scheme is verified by the computer simulation and experiment with the miniature of the container crane system.

• Journal of Industrial Technology
• /
• v.22 no.B
• /
• pp.241-249
• /
• 2002

Optical fiber is indispensable for optical communication systems that transmit large volumes of data at high speed, but super precision technology in sub-micron units is required for optical axis adjustment. We developed the automatic optical fiber by image processing and automatic loading system. we have developed 6-axis micro stage system for I/O optical fiber arrays, the initial automatic aligning system software for a input optical array by the image processing technique, fast I/O-synchronous aligning strategy, the automatic loading/unloading system and the automatic UV bonding mechanism. In order to adjust the alignment it used on PC based motion controller, a $10{\mu}m$ repeat-detailed drawing of automatic loading system is developed by a primary line up for high detailed drawing. Also, at this researches used the image processing system and algorithm instead of the existing a primary hand-line up and fiber input array and waveguide chip formed in line by automatic.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.492-496
• /
• 1987

The testing philosophy and control schemes are investigated and applied to construct the Automatic Microwave Leakage Inspection System (AMLIS) . AMLIS is consists of three major parts such as Material Handling Mechanism, Fine Positioning Mechanism and Scanning Mechanism. The material Handling unit is designed to perform loading and unloading microwave oven onto the testing point by pneumatic cylinder and vacuum pump. The Fine positioning part includes X-Y-.THETA. table and distance sensing equipment. The scanning part is composed of five SCARA robots, which traverse X-Y-Z catesian coordinates respectively. The leakage testing probes are placed at the end of this each robot then the path and speed are both controlled via microprocessors. A performance test of this system combined with electric parts and software is done and the basic major function of system are accomplished.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.175-180
• /
• 2002

Loading/Unloading(L/UL) mechanism has been considered to be an alternative to contact start-stop(CSS) mechanism which eliminates stiction and wear associated with frequent start and stop process. It has other advantages including increased areal density due to lower flying height, reduced power consumption, and improved shock resistance. In order for L/UL to be Implemented in Near-field recording system properly, dynamics of optical flying head must be understood and optimized. In this paper the dynamic characteristics during loading process is analyzed numerically to investigate the effect of design parameters such as loading speed. slider shape, and initia conditions on the dynamic reponses of flying head..

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.3
• /
• pp.243-249
• /
• 2005

The present study has been conducted to simulate dynamics of a gas engine-driven heat pump(GHP) for design of control algorithm. The dynamic modeling of a GHP was based on conservation laws of mass and energy. For automatic control of refrigerant pressures, actuators such as engine speed, outdoor fan, coolant three-way valves and liquid injection valve were PI or P controlled. The simulation results showed physical behavior that is realistic enough to apply for control algorithm design.