• Journal of the Korean Applied Science and Technology
• /
• v.28 no.4
• /
• pp.410-417
• /
• 2011

Effects of ethylene-propylene diene monomer (EPDM)/polypropylene (PP), zinc oxide, stearic acid, and clay on the combustive properties based on EDPM/PP were investigated. The EDPM/PP/clay nanocomposites was compounded to prepare specimen for combustive analysis by cone calorimeter (ISO 5660-1). It was found that the specific mass loss rate (SMLR) in the nanocomposites decreased due to the fire resistance compared with unfilled EDPM/PP, while the nanocomposites showed the higher total heat release (THR), higher CO production release, and higher specific extinction area (SEA) than those of virgin EPDM/PP. The stearic acid for softening ruber increased the THR and amount of smoke by itself, combustible.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.435-441
• /
• 2010

In this study, numerical simulations were carried out to investigate the effect of verification core hole on the shaft tip capacity. The verification core extreted at shaft tip may deteriorate the shaft tip capacity when the clay shales (Taylor Marl) surrounding the shaft degrades and the empty core hole remains unfilled. Series of finite element analyses were conducted using Mohr-Coulomb model with total stress material parameters that were obtained from laboratory testing. The numerical analyses indicate that the shaft tip capacity does not decrease for most cases, and the maximum reduction does not exceed 5%.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.6
• /
• pp.1026-1031
• /
• 2016

Neat Epoxy, nano alumina composites, micro alumina composites and multi-nano alumina composites were prepared and experiment were performed to measure their partial discharge resistant characteristics. The partial discharge resistance obtained for the microcomposites, nanocomposites and multi-nanocomposites are compared with those of unfilled epoxy and with GDE amount for surface modifier. It was observed that compare multi-nano alumina composites to micro alumina composites, the partial discharge resistance to degradation gets improved considerably. The improvement in the degradation resistance is attributed to the interface intension between the nano alumina composites and GDE, micro alumina and epoxy neat.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.5
• /
• pp.945-952
• /
• 2023

In this study, the sand casting process was applied to design the gating system and perform casting simulation in order to domestically produce the submarine mast cover. Based on simulation results, casting experiments were conducted to produce a soundness prototype. The design concept of the mast cover's gating system was based on the design of bell casting. By arranging eight tower-type gates in a circle at 45° intervals, the flow of melt flowing into each gate was uniform and did not mix with each other, and the velocity of melt was also uniform. The mast cover made of Ni-Al-Bronze alloy has no unfilled parts. However, small porosities and flow marks occurred on the surface in several places. Yield strength and ultimate tensile strength are 279.3 MPa and 675.7 MPa, respectively, and elongation is 21.2%.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.6
• /
• pp.294-300
• /
• 2005

According to the trend for electric power equipment of high capacity and reduction of its size, the needs for the new high performance electric equipments become more and more important. On of the possible solution is high temperature superconducting (HTS) power application. Following the successful development of practical HTS wires, there have been renewed activities in developing superconducting power equipment. HTS equipments have to be operated in a coolant such as liquid nitrogen ($LN_2$) or cooled by conduction-cooling method such as using Gifford-McMahon (G-M) cryocooler to maintain the temperature below critical level. In this paper, the dielectric strength of some insulating materials, such as unfilled epoxy, filled epoxy, and polyimide in $LN_2$ was analyzed. Epoxy is a good insulating material but fragile at cryogenic temperature. The filled epoxy composite not only compensates for this fragile property but enhances its dielectric strength.

• Elastomers and Composites
• /
• v.46 no.3
• /
• pp.237-244
• /
• 2011

Five natural rubber (NR) composites with different reinforcing systems of unfilled, carbon black, carbon black with silane coupling agent, silica, and silica with silane coupling agent were thermally aged and change of the crosslink densities by the accelerated thermal aging was investigated. The crosslink densities on the whole increased as the aging time elapsed irrespective of the reinforcing systems. The crosslink density changes became noticeable by increasing the aging temperature. For carbon black-filled composites, the silane coupling agent made the crosslink density change to be increased. For silica-filled composites, however, the silane coupling agent made the crosslink density increment reduced at 60 and $70^{\circ}C$ and it hardly affect the degree of the crosslink density change at 80 and $90^{\circ}C$. The activation energies for the crosslink density changes of the carbon black-filled samples increased continuously in a logarithmic fashion, whereas that of the silica-filled one showed a quasi-steady state ranges at aging times of 30-150 days. The activation energy of the unfilled sample increased exponentially with the aging time. The experimental results were explained with sulfur donation from the silane coupling agent, surface modification of the filler by the silane coupling agent, adsorption of curative residues on the silica surface, and release of the adsorbed curative residues.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.2
• /
• pp.7-12
• /
• 2009

The effects of refining either SwBKP or HwBKP, and both of SwBKP and HwBKP on the physical properties of paper were investigated in order to elucidate if the non-conventional refining and blending method can be used for the optimizing the paper properties. The blending ratio of SwBKP and HwBKP was 15:85. The highest bulk was obtained with the refining of SwBKP only. Any differences of opacity were not observed in unfilled paper, while the highest opacity of PCC filled paper was obtained at same bulk when the only HwBKP was refined. However burst index and tensile index did not showed any differences in the relationship with bulk. Therefore this result can be applied to improve the opacity of paper without sacrificing of strength properties.

• International Journal of Concrete Structures and Materials
• /
• v.2 no.2
• /
• pp.145-152
• /
• 2008

So far, there has been no study of the concrete to strengthen in the lining of the tunnels, except for the study of the stability of subgrade and the tunnel construction technologies. In the existing concrete work for tunnel lining, lots of problems happen due to the partial compaction and the material segregation after casting concrete. Accordingly, the aim of this study is to improve economic efficiency and secure durability through the improvement of the construction performance and quality of the concrete for the tunnel lining among the civil structures. Therefore, the compactability and strength properties of the High Flowing Self-Compacting Lining Concrete (HSLC) are evaluated to develop the mixing proportion for design construction technology of HSLC that can overcome the inner cavity due to the reduced flowability and unfilled packing, which has been reported as the problem in the existing lining concrete. The result of the evaluation shows that the ternary mix meets the regulations better than the binary mix. Consequently, it has been judged applicable to the cement for tunnel lining.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.41 no.1
• /
• pp.86-94
• /
• 1996

This experiment was carried out to investigate the differences of the growth and yield characteristics at different planting dates in two soybean ecotypes from 1993 to 1994. Two summer types of soybean varieties, Suwon 163 and CNS 342, and two autumn types, Hwangkumkong and Keomcheongkong ＃1 were planted 7 times from 22 April to 21 June with 10 days interval in 1993 and 4 times from 22 April to 21 June with 20 days interval in 1994 at experimental field, Dankook University, Cheonan. Emergence rate was shown to difference between the summer types and the autumn types, as planting date delayed and between 1993 and 1994. The average emergence period was more shortened in 1994 than 1993. This was reduced as planting date delayed. Days to flowering, pod formation and maturity were shortened as planting date delayed, and observed that shortening of days to flowering and maturity were smaller in the summer types than the autumn types. Stem height, stem diameter, number of mainstem nodes, number of branches and number of branch nodes were different between the summer types and the autumn types and between 1993 and 1994. These were reduced as planting date delayed. The number of pods per plant was also different between 1993 and 1994, and reduced as planting date delayed. The number of seeds per pod was not different between 1993 and 1994, and shown to similar tendency as planting date delayed. It was observed that one hundred seed weight of the summer types were reduced, but the autumn types were not as planted date delayed in 1993. In 1994, one hundred seed weight was not measured because almost all pods were unfilled or shriveled probably due to high temperature during pod formation period. The rate of unfilled pods per plant was higher the autumn types than in the summer type of soybeans in 1994.

• Design & Manufacturing
• /
• v.6 no.2
• /
• pp.59-63
• /
• 2012

In various industries, tactile recognition has been one of the important ways in displaying information because peoples like to touch and feel. Especially, how much the tactile information is efficiently recognizable is crucial for visually impaired persons in their daily lifes. However, existing design guidelines are insufficient to lead good tactile recognition. In this study, an experiment was performed to investigate proper tactile shapes (relievo / intaglio vs. filled / unfilled), sizes and depths for efficient tactile recognition. Moreover, this study scrutinized whether the recognition speed or error was varied depending on the type of displayed symbols (open vs. closed types) in tactile. The experimental results revealed that the 'relieve-filled' shape type was more rapidly recognizable than the other shapes, and the 'closed' type symbols (e.g., ${\square }$. ${\bigcirc}$) were more robustly recognizable than the 'open' type symbols (e.g, +, ^). Several design guidelines were presented based on the results. These guidelines can be applied to the design of tactile buttons in the devices that users should control them without visual attention, such as car steering wheels or MP3 players.