• 한국정밀공학회지
• /
• 제28권3호
• /
• pp.265-274
• /
• 2011

This paper presents current state of the prediction simulator of structural characteristics of machinery equipment accuracy. Developed accuracy prediction simulator proceeds and estimates the structural analysis between the designer and simulator through the internet for convenience of designer. 3D CAD model which is input to the accuracy prediction simulator would simplified by the process of removing the small hole, fillet and chamfer. And the structural surface joints would be presented as the spring elements and damping elements for the structural analysis. The structural analysis of machinery equipment joints, containing rotary motion unit, linear motion unit, mounting device and bolted joint, are presented using Finite Element Method and their experiment. Finally, a general method is presented to tune the static stiffness at a rotation joint considering the whole machinery equipment system by interactive use of Finite Element Method and static load experiment.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.493-497
• /
• 2000

A battery is the device that transforms the chemical energy into the direct-current electrical energy without a mechanical process. Unit cells are connected in series to obtain the required voltage while being connected in parallel to organize capacity for load current. Because the voltage drop down in one set of battery is faster than in two one it may result in the low efficiency of power converter with the voltage drop and cause the system shutdown. However when the system being shutdown. However when the system being driven in parallel a circular-current can be generated,. It is shown that as a result the new batteries are heated by over-charge and over-discharge and the over charge current increases rust of the positive grid and consequently shortens the lifetime of the new batteries. The difference between the new batteries and old ones is the amount of internal resistance. In this paper we can detect the unbalance current using the microprocessor and achieve the balance current by adjusting resistance of each set, The internal resistance of each set becomes constant and the current of charge and discharge comes to be balanced by inserting the external resistance into the system and calculating the change of internal resistance.

• 한국지열·수열에너지학회논문집
• /
• 제12권4호
• /
• pp.15-20
• /
• 2016

Even though the control device of the heating system works well, insufficient water flow rates can degrade control performance and thermal comfort. The water flow rate should be adjusted appropriately to cope with the heating load of each zone. In order to solve these problems, a new balancing concept 'dynamic balancing' was proposed where a balancing valve opening can be automatically modulated according to the heating condition of the room. This study analyzed the effects of dynamic balancing upon indoor thermal environment and energy consumption in a radiant floor heating system through field measurement. Under part-load conditions, the use of a dynamic balancing is a more effective method to reduce energy consumption and to prevent a cavitation. Dynamic balancing is able to help boost the temperature of a room in the start-up period.

• 드라이브 ㆍ 컨트롤
• /
• 제18권1호
• /
• pp.9-16
• /
• 2021

Overloaded vehicles increase the maintenance cost of road structures, and they are a major factor in causing damage to the roads and bridges. In addition, overloaded vehicles compromise the braking capability of the vehicle; thus, threatening the safety of the driver. In order to prevent overloading of vehicles, the government is cracking down on the roads by using a device that measures the weight of vehicles. But this process is inconvenient because the place where the equipment is installed is far away from where the cargo is loaded. Due to the limitations of these fixed weighing devices, there is a growing need for technology that can monitor vehicle weight distribution and overload conditions in real time. In this work, we develop an onboard scale that can measure the load (weight) of trucks in real time. The onboard scale consists of high sensors, a signal processing unit, and a display, and it measures the load using height-displacement of the vehicle's leaf spring suspension.

• 조명전기설비학회논문지
• /
• 제23권12호
• /
• pp.106-114
• /
• 2009

본 논문에서는 전력시장 환경에 있어서 신재생 에너지를 포함한 마이크로그리드의 최적운영을 위한 발전계획 방안을 제시하였다. 마이크로그리드는 전력과 동시에 열을 공급할 수 있는 소규모 전력공급시스템으로 경제성 확보를 위한 운전최적화 알고리즘이 필요하다. 따라서 신재생 에너지는 발전 즉시 부하에 전력을 공급하도록 하고, 배터리는 부하평준화에 이용한다. 동적계획법을 적용하여 마이크로그리드 운전에 따른 수익 최대화가 가능한 마이크로그리드 운전 최적화 프로그램을 개발하였으며, 독립운전 및 계통연계 운전모드에서 개발 프로그램의 사레연구를 통해 프로그램의 유효성을 보이고 있다. 제안된 마이크로그리드 최적운영 프로그램은 향후 마이크로그리드 시장이 형성 되면 마이크로그리드의 경제적 운전기법 개발에 적용이 가능하다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(2)
• /
• pp.88-91
• /
• 2000

An MMIC oscillator operating at the 24.55 GHz has been designed using 0.2 ${\mu}{\textrm}{m}$AlGaAs/InGaAs/GaAs Pseudomorphic HEMT technology. The active device used in the oscillator design has a 0.2 ${\mu}{\textrm}{m}$ gate length PHEMT with 4$\times$80 ${\mu}{\textrm}{m}$ gate width. We obtained 4.08 dB of S$_{21}$ gain and 317 mS/mm of transconductance, and extrapolated unit current gain cut-off frequency (f$_{T}$) and maximum oscillation frequency (fmax) were 62 GHz and 120 GHz, respectively. The circuit are based on a series feedback and negative resistance topology. Microstrip line open stub is used to terminating. The oscillator circuits has designed for delivering maximum power to load and conjugated matching. The simulated small signal negative resistance was 50 Ω. We obtained 1.002 of loop gain and 0.0005$^{\circ}$angle from the simulation by HP libra 6.1. The layout for oscillator is 1.2$\times$1.8 $\textrm{mm}^2$.>.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2006년도 춘계학술발표대회
• /
• pp.597-600
• /
• 2006

인터넷 기술의 발전으로 우편물류시스템은 우편집중국을 중심의 허브-스포크 구조를 기반으로 자동화 우편소통 시설과 우편물류정보시스템 구축 등의 많은 변화와 발전을 해왔다. 현행 우편물류정보시스템은 바코드를 기반으로 정보의 교환 및 처리를 수행하며, 물류정보의 수집, 처리 및 활용에 있어서 실시간성과 동적인 운용 측면에서 진일보하기 위해서는 차세대 정보기술인 RFID를 지원하기 위한 연구가 필요하다. 따라서 이 논문에서는 우편물류의 운송용기를 중심으로 업무 및 시스템을 분석하며, 업무 효율성과 생산성 개선을 위해 RFID 기술을 적용하기 위한 정보처리시스템 모형을 설명한다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1038-1041
• /
• 2004

In this study, developed a micro-level experimental setup to measure pore pressure and poroelastic modulus in various strain and strain rate about a stress in micro-structure of bone tissue. It is essential device in the development of the model to analysis the interstitial bone fluid flow of the lacuno-canalicular system to be known that would effect on the bone remodeling. The constitution of the experimental setup is as follows, microscopic image processing system; actuator control unit; load measurement system. A pilot study was used an artificial chemical wood to have similar poroelastic property of bone matrix and conducted to validate the suitability of the measurement system.

• 산업경영시스템학회지
• /
• 제29권1호
• /
• pp.135-142
• /
• 2006

The package loading process of tile lumbering industry is an operation that after a pair of workers binds three or six lumber into a unit and cut the both ends of the lumber, carry and pack and load the weight cargo of 30-50kg. The package loading process causes lots of noise and wood dust when the lumber are cut and brings about the main cause of the musculoskeletal disorder when workers carry the heavy goods. Therefore, we developed the monolithic package loading equipment cutting both ends that is enable to improve the working method and environments of the existing package loading process. The noise and wood dust were reduced by developing the device and the main cause of shirking duties on working place was solved by preventing the musculoskeletal disorder and improving the working environments as excluding the work of carrying heavy goods.

• 한국포장학회지
• /
• 제21권1호
• /
• pp.11-17
• /
• 2015

글로벌 산업화 및 경제성장으로 국내외 교역량이 증가함에 따라 국가 물류비 부담이 지속적으로 상승되면서, 선진국이나 글로벌 선진기업의 경우와 마찬가지로 국내에서도 이러한 국가물류비 감소를 통한 산업 경쟁력 제고를 위해 다양한 물류 효율화를 시도해 왔다. 특히 2000년대 초반 유닛로드시스템(Unit Load System)을 도입을 통해 T11($1100{\times}1100mm$)의 표준파렛트를 설정하였고, 이를 기준으로 포장 모듈 및 물류 설비가 정합성을 유지하도록 물류설비인증제도를 시행함으로써 물류표준화 확산과 동시에 3자 물류의 확산을 통한 물류효율화가 진행되면서 국가물류비 절감에 상당부분 기여해왔으나, 최근 인증수요의 감소와 함께 GDP 대비 국가물류비 비율에서 아직 선진국과 약 3%정도 격차를 보이고 있다. 따라서, 본 연구에서는 국내 물류분야 인증제도에 대한 현황 및 실효성 분석을 통해 국가 물류 효율화 및 선진화와 동시에 물류산업 활성화를 위한 정책적 전략으로서의 물류인증 활성화 방안으로 인증 수요자의 니즈를 충족하는 수요기반의 물류인증제도 도입을 제안하였다. 즉, 동북아 교역량의 증가에 대응한 순환물류시스템(Returnable Transport System) 도입 필요성을 반영한 '동북아 물류설비 인증' 개발과 전자 상거래의 초국경적 글로벌 유통에 따른 '안전운송 인증'과 같은 수요기반의 인증 도입을 통해 물류산업 지원과 활성화에 기여할 것으로 기대된다.