• Nuclear Engineering and Technology
• /
• v.50 no.7
• /
• pp.1120-1130
• /
• 2018

An analysis of a pyroprocessing safeguards methodology employing the Pu-to-$^{244}Cm$ ratio is presented. The analysis includes characterization of representative used nuclear fuel assemblies with respect to computed nuclide composition. The nuclide composition data computationally generated is appropriately reformatted to correspond with the material conditions after each step in the head-end stage of pyroprocessing. Uncertainty in the Pu-to-$^{244}Cm$ ratio is evaluated using the Geary-Hinkley transformation method. This is because the Pu-to-$^{244}Cm$ ratio is a Cauchy distribution since it is the ratio of two normally distributed random variables. The calculated uncertainty of the Pu-to-$^{244}Cm$ ratio is propagated through the mass flow stream in the pyroprocessing steps. Finally, the probability of Type-I error for the plutonium Material Unaccounted For (MUF) is evaluated by the hypothesis testing method as a function of the sizes of powder particles and granules, which are dominant parameters to determine the sample size. The results show the probability of Type-I error is occasionally greater than 5%. However, increasing granule sample sizes could surmount the weakness of material accounting because of the non-uniformity of nuclide composition.

• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3525-3534
• /
• 2023

Non-uniformity of Pu and Cm composition in used nuclear fuel was analyzed to determine its effect on Pu accountancy in pyroprocessing, while employing the Pu-to-²⁴⁴Cm ratio method. Burnup simulation of a typical pressurized water reactor fuel assembly, required for the analysis, was carried out using MCNP code. Used fuel nuclide composition, as a function of nine axial and two radial meshes, were evaluated. The axial variation of neutron flux and self-shielding effects were found to affect the uniformity of Pu and Cm compositions and in turn the Pu-to-²⁴⁴Cm ratio. However, the results of the study showed that these non-uniformities do not affect the use of Pu-to-²⁴⁴Cm ratio method for Pu accountancy, if the measurement samples are drawn from the voloxidized powder at the feed step of pyroprocessing. 'Material Unaccounted For' and its uncertainty estimates are also presented for a pyrprocessing facility to verify safeguards monitoring requirements of the IAEA.

• Journal of ILASS-Korea
• /
• v.20 no.2
• /
• pp.95-100
• /
• 2015

Lower recirculated gas temperature at EGR system reduces NOx and PM emissions. However, EGR Cooler can be polluted by PM generated from recirculated EGR gas, and it reduces cooling efficiency and the amount of EGR gas simultaneously. The SECFR(Steam EGR Cooler Fouling Remover) system which uses the evaporated washer fluid steam caused by high temperature of EGR gas was manufactured for removing fouling generated on the cooler surface. Since an injection pressure of wind shield washer fluid in the vehicle is approximately 0.5 bar, it is not enough to atomize the injected washer fluid. Thus, it is necessary to apply a method to atomize the washer fluid. In this study, the impinging plate was used to promote the atomization of spray washer fluid for the purpose of apply SECFR system to vehicles and measured the DAR(Droplet Area Ratio) and DUI(Droplet Uniformity Index) through the spray visualization.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.2
• /
• pp.7-11
• /
• 1999

In this paper, the result of study in artificial lighting uniformity ratio yield Irethod subjtrt to lecture room are reported. It is desirable that the aWication of equation $\circled1 U=Ei/Ex\times100$ cannot be used to the rrean value in place to be efftrtive of light and darkness. And it is desirable that the awlication of equatioo $\circled2 U=Ei/Ea\times100$ or equation $\circled3 U=(Ea-Ei)/Ea\times100$ be used to the rrean Value equality illumination conditioos. Also, requiring preparation of judgarent standard, uniformity ratio equation agree with actual circumstances in this country. It must be considerai intensity of illumination and specificity of space in established standard.andard.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.1
• /
• pp.296-305
• /
• 2012

In this paper, we develop about glare phenomenon at security light caused by light source's straight characteristic, maintaining uniformity ratio of illuminance as high, have long light distribution not by symmetry of rotation but a single axis. we develop second lens for security light that lack of light distribution phenomenon at each of security light can be solved. Our developed light system design satisfies lighting standard of security light's and shape of lens is single lens. so our lens optimizes designing or analysis by using lighting design and interpretation program. Making a Mock-up to do real measure, we have intensity of illumination and maintaining uniformity ratio of illuminance measurement data.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.15-24
• /
• 2013

Numerical studies were conducted to investigate the internal flow field and combustion characteristics of DISI engine with methanol blended in gasoline. Dual injection was applied and the characteristics were compared to single injection strategy. The amount of the fuel injection was corresponded to air-fuel ratio of each fuel for complete combustion. The preforming model in this study, software STAR-CD was employed for both modeling and solving. The operating speed condition were at 4000 rpm/WOT (Wide open throttle) where the engine was fully warmed. The results of single injection with M28 showed that the uniformity, equivalence ratio, in-cylinder pressure and temperature increased comparing to gasoline (M0). When dual injection was applied, there was no significant change in uniformity and equivalence ratio but the in-cylinder pressure and temperature increased. When M28 fuel and single injection was applied, the CO (Carbon monoxide) and NO (Nitrogen oxides) emission inside the combustion chamber increased approximately 36%, 9% comparing with benchmarking case in cylinder prior to TWC (Three Way Catalytic converter). When dual stage injection was applied, both CO and NO emission amount increased.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.31 no.2
• /
• pp.58-69
• /
• 2003

The Hemi-sphere projection method produces an image that includes all surrounding visual landscape from a view point. This characteristic can solve the problem of perspective method that has only a limited view angle, and thus can be a potentially effective method for the analysis of visual landscape. This study tried to adopt the hemi-sphere projection method in the evaluation of streetscape, and examined its effectiveness and possibilities. Computer animations using the perspective method and the hemi-sphere method were produced for Bang-Hak Ro, Seoul, and the kames of the animations were reclassed to identify the visibility ratio of physical elements(buildings, sky and mountains). A preference questionnaire was given to 51 university students, and the relationships between the visibility ratio and visual preference were analyzed. The results showed that visual preference of streetscape can be explained by three factors: Openness, Uniformity, and Variousness, accounting for 63.2% of the total variance, and among which Openness showed the highest proportion at 32.1％. The visibility ratio calculated by the hemi-sphere method yielded strong correlation coefficients with Openness, and it was much higher than with the perspective method. The hemi-sphere method also produced significant correlation coefficients about Uniformity and Variousness, but the perspective method could not. The results demonstrated that the hemi-sphere method can provide more accurate observation of visual changes, and that it can be an effective method for the analysis of streetscape.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.420-425
• /
• 2018

Purpose: Chemical fertilizers contribute to agricultural productivity. Annually, 450,000 tons of chemical fertilizers are used in Korea, which is 268 kg per hectare (MAFRA, 2016). However, excessive use causes problems such as environmental pollution and soil acidification. This study proposes use conditions for a fertilizer distributor that can reduce excessive fertilization by analyzing distribution patterns. Methods: This study analyzed fertilizer application uniformity according to the number of blades on a centrifugal fertilizer distributor (three or four blades), orifice gate open ratio (50 or 100%), and blade rotation speed (400, 500, or 600 rpm). Results: When using four blades, the coefficient of variation (CV) was lower than when using three by 11-13% points, and the CV using the 50% open ratio was 10-30% points lower than using the 100% open ratio. The CV at 500 rpm blade rotating speed was 9-12% points lower than that for 400 and 600 rpm. Conclusions: The CV with four blades, 50% orifice gate open ratio, and 500 rpm of blade rotating speed was 18.4%, which provided the most uniform fertilization.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.17 no.1
• /
• pp.25-29
• /
• 2013

Purpose: In this study, we evaluated the accuracy of CT-based attenuation correction (AC) under the conventional CT protocol (140 kVp, on average 50-60 keV) by comparing the SPECT image qualities of different energy of radioisotopes, $^{201}Tl,\;^{99m}Tc$ and $^{131}I$. Materials and Methods: Using a cylindrical phantom, three different SPECT scans of $^{201}Tl$ (70 keV, 55.5 MBq), $^{99m}Tc$ (140 keV, 281.2 MBq) and $^{131}I$ (364 keV, 96.2 MBq) were performed. The CT image was obtained with 140 kVp and 2.5 mA in GE Hawkeye 4. The OSEM reconstruction algorithm was performed with 2 iterations and 10 subsets. The experiments were performed in the 4 different conditions; non-AC and non-scatter correction (SC), only AC, only SC, AC and SC in terms of uniformity and center to peripheral ratio (CPR). Results: The uniformity was calculated from the uniform whole region in the reconstructed images. For $^{201}Tl$ and $^{99m}Tc$, the uniformities were improved by about 10-20% AC was applied, but these were decreased by about 2% as SC was applied. The uniformity of $^{131}I$ was slightly increased as both AC and SC were applied. The CPR of the reconstructed image was close to one, when AC was applied for $^{201}Tl$ and $^{99m}Tc$ scans and $^{131}I$ was distant from 1 and that is only AC. Conclusion: The image uniformity improved by AC on low energy likely to $^{201}Tl$ and $^{99m}Tc$. However, image uniformity of high energy such as $^{131}I$ was improved, when both AC and SC was applied.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.432-435
• /
• 2004

MSC (Multi Spectral Camera) system is a remote sensing payload to obtain high resolution ground image. In this application, uniformity characteristic is important as well as GSD (Ground Resolved Distance) and SNR (Signal to Noise Ratio). MSC image chain is consisted of OM (Optical Module), CCD, Video processor, NUC and DCSU (Data Compression and Storage Unit). Each block makes and corrects MSC's nonuniformity response. This paper shows the cause of nonuniformity error and the correction scheme of MSC system from the electronic point of view.