• Korean Journal of Agricultural Science
• /
• v.5 no.2
• /
• pp.49-55
• /
• 1978

In order to get healthy seedling of rice suitable for rice transplanter, the growing characteristics of the seedling grown under different growing days and sowing densities were invesigated and the results obtained were summarized as follows; In the 20 days old seedling, the difference of growing state of seed ling and its characteristics between the two types of nursery bed was not found, but for the 30 days old seedling, both of the crop growth rate and the relative growth rate on the band-type nursery bed appeared higher than those on the mat-type nursery bed. And also, "the dry weight, the content of cardohydrate and the ratio of dry weight to plant height of the seedling grown on the band-type nursery bed were much higher than those on the mat-type nursery bed, however the amount of difference of seedling characteristics between two types of nursery bed was decreased for 40 days old seedling and leaf number was not increased. The amount of the seedling growth was increased with less density of sowing and for the difference between the higher and the less density, the difference getting bigger with the longer nursery days. The maximum density of sowing was approximately 200cc per nursery case on the band-type nursery bed and 250cc per nursery case on the mat-type nursery bed. It was seemed that the growing uniformity of the seedling grown on the mat-type nursery bed was better than that on the band- type nursery bed, As the coefficient of variation of the plant height and the leaf numbers of the seedling grown on the band- type nursery bed was higher than that on the mat-type nursery bed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.10
• /
• pp.1161-1170
• /
• 2011

This paper presents a solution to the inverse problem for the service boundary conditions of thermal-flow and structure analysis in a catalyst substrate. The exhaust-gas purification efficiency of a catalyst substrate is influenced by the shape parameter, catalyst ingredients and so on and is estimated by the thermal flow uniformity. The formulations of the inverse problem of obtaining the thermal-flow parameters (inlet temperature, velocity, heat of reaction, convective heat-transfer coefficient) and the direct problem of estimating from a given outlet temperature distribution are described. An experiment was designed and the response-surface optimization technique was used to solve the proposed inverse problem. The temperature distribution of the catalyst substrate was obtained by thermal-flow analysis for the predicted thermal-flow parameters. The thermal stress and durability assessments for the catalyst substrate were performed on the basis of this temperature distribution. The efficiency and accuracy of the inverse approach have been demonstrated through the achievement of good agreement between the thermal-flow response surface model and the results of experimental vehicle tests.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.7
• /
• pp.777-784
• /
• 2005

The first flush phenomenon is defined as the initial period of road runoff during which the concentration of pollutants was significantly high. Road runoff contains significant loads of micro-particles, heavy metals and organic constituents. There were two major objectives of this study. The first objective was to characterize the road runoff. The second objective was to measure and evaluate particle sire distribution of the road runoff, Stormwater runoff was monitored on two sites of four lane road areas along with traffic volume. A total six storm events were monitored to characterize the road runoff. The quantity of road runoff and quality constituents, including chemical oxygen demand ($COD_{Cr}$), suspended solids(SS), total Kjeldahl nitrogen (TKN), ortho-phosphorus ($PO_4-P$), total phosphorus(TP), heavy metals and particle size distribution were analyzed. The results indicate that the concentration of SS, $COD_{Cr}$, TKN and TP ranges were $45{\sim}2,396\;mg/L$, $40{\sim}931\;mg/L$, $0.1{\sim}19.6\;mg/L$, and $0.2{\sim}25.1\;mg/L$, respectively. The results of the regression analysis between SS and the others constituents shows that $COD_{Cr}$, TP, Cu, Pb were highly correlated. And the results showed that the mean range of particle size and uniformity coefficient for road runoff were $6.7{\sim}23.4{\mu}$ and $6.4{\sim}10.2$, respectively.

• Geophysics and Geophysical Exploration
• /
• v.16 no.2
• /
• pp.79-90
• /
• 2013

Geophysical investigation in non-destructive testing is economically less expensive than boring testing and providing geotechnical information over wide-area. But, it provides only limited geotechnical information, which is hardly used to the design. Accordingly, we performed electrical resistivity experiments on large scale of soil model to analyze the correlation between electrical resistivity response and soil water contents. The soils used in the experiments were the Jumunjin standard sand and weathered granite soil. Each soil particle size distribution and coefficient of uniformity of experimental material obtained in the experiments were maintained in a state of the homogeneous. The specifications of the model used in this study is $160{\times}100{\times}50$(cm) of acrylic, and each soil was maintained at the height 30 cm. The water content were measured using the 5TE sensors (water contents sensors) which is installed 7 ~ 8 cm apart vertically by plugging to floor. The results of the resistivity behavior pattern for Jumunjin standard sand was found to be sensitive to the water content, while the weathered granite soil was showing lower resistivity over the time, and there was no significant change in behavior pattern observed. So, it results that the Jumunjin standard sand's particle current conduction was better than the weathered granite soil's particle through contact with the distilled water. This lab test was also compared with the result of a test bed site composed of similar weathered soil. It was confirmed that these experiments were underlying research of non-destructive investigation techniques to improve the accuracy to estimate the geotechnical parameter.

• Asian Journal of Turfgrass Science
• /
• v.24 no.1
• /
• pp.31-35
• /
• 2010

Several experiments were conducted to investigate the germination characteristics among the Rumex crispus, R. japonicus, R. obtusifolius, and R. nipponicus. The germination point of R. japonicus was started 4 days after application, and then R. obtusifolius (5th), R. crispus (6th), R. nipponicus (10th) with appeared order. The optimum temperatures for germination of all tested Rumex spp. occurred at the $15^{\circ}C$. Especially, R. obtusifolius will have the widest germination range at $10^{\circ}C{\sim}30^{\circ}C$. To compared with 1996 and 2004 year selected R. japonicus germination were did not significantly difference, otherwise, all tested Rumex spp. on dark condition was not germinated. The parameters of germination characteristics of Rumex spp. were investigated mean germination rate (MGR, %), mean germination time (MGT, day), mean germination velocity (MGV, No./day), and coefficient of germination uniformity (CGU). The R. japonicus compared in tested Rumex spp. showed the highest MGR. The MGT and MGV of R. obtusifolius was appeared the earliest compared with R. obtusifolius and R. crispus.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.750-757
• /
• 2018

The mechanically stabilized earth wall abutment is an earth structure using a mechanically stabilized earth wall and it uses in-extensional steel reinforcements having excellent friction performance. In order to analyze the pullout behavior of in-extensional steel reinforcements usually applied on the mechanically stabilized earth wall abutment, effects of stiffness and particle-size distributions of backfills and also horizontal spacings were considered in this study. As a result of parametric analyses, the highest pulling force acted on the uppermost reinforcement, and the stiffness and the particle-size distributions of the backfill significantly affected the pulling resistance of the reinforced soils. The internal friction angle of backfills should be at least 25 degrees, the coefficient uniformity factor should be at least 4, and the horizontal spacing of the uppermost steel reinforcement should be less than 25cm. Therefore, in order to secure the pullout resistance of the reinforced soil, it is necessary a properly spacing of reinforcement and more strict quality control for the backfill.

• Journal of Korean Society of Forest Science
• /
• v.111 no.3
• /
• pp.418-427
• /
• 2022

Our aim was to evaluate the quality of pine seeds after long-term storage and to analyze the correlation between germination and physiological characteristics. Therefore, we investigated the germination and physiological characteristics of seeds stored for different periods and storage temperatures. Pine seeds lost little viability and vigor after 12 years of storage at 4℃; it is even possible to prolong the storage period at -18℃. The deterioration process operating through long-term storage was characterized by a loss of seed vigor before a loss in seed viability. Electrical conductivity of the seed leachate was significantly higher in seeds that completely lost their viability, and was also found to be significantly correlated with the germination percentage, T50, mean germination time, and germination speed. Among the minerals leaked to the leachate, K had the highest concentration, followed by Na, Ca, Cu, Mg, and Fe, while Mn and Zn were not detected. Concentrations of K, Ca, Cu, Mg, and Fe in the leachate differed significantly by treatment, and in the cases of K, Ca, Cu, Na, and Mg, we observed large differences in the leachate between the seeds that were collected in 2003 and those collected in other years.. Germination percentage was significantly negatively correlated to the concentrations of Ca, Cu, K, Mg, and Na. The coefficient of uniformity of germination was significantly negatively correlated to Cu concentration. The other germination characteristics were not significantly correlated with the mineral concentration. Therefore, the mineral concentrations of pine seed leachate were not reliable indicators of seed deterioration when the differences in quality between seed lots were small. However, electrical conductivity could be an indicator of seed viability and vigor of pine seeds under long-term storage.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.46 no.3
• /
• pp.15-22
• /
• 2023

BNKT Ceramics, one of the representative Pb free based piezoelectric ceramics, constitutes a perovskite(ABO3) structure. At this time, the perovskite structure (ABO3) is in the form where the corners of the octahedrons are connected, and in the unit cell, two ions, A and B, are cations, A ion is located at the body center, B ion is located at each corner, and an anion O is located at the center of each side. Since Bi, Na, and K sources constituting the A site are highly volatile at a sintering temperature of 1100℃ or higher, it is difficult to maintain uniformity of the composition. In order to solve this problem, there should be suppression of volatilization of the A site material or additional compensation of the volatilized. In this study, the basic composition of BNKT Ceramics was set to Bi_0.5(Na_0.78K_0.22)_0.5TiO₃ (= BNKT), and volatile site (Bi, Na, and K sources) were coated in the form of a shell to compensate additionally for the A site ions. In addition, the physical and electrical properties of BNKT and its coated with shell additives(= @BNK) were compared and analyzed, respectively. As a result of analyzing the crystal structure through XRD, both BNKT(Core) and @BNK(Shell) had perovskite phases, and the crystallinity was almost similar. Although the Curie temperature of the two sintered bodies was almost the same (TC = 290 ~ 300 ℃), it was confirmed that the d33 (piezoelectric coefficient) and Pr (residual polarization) values were different. The experimental results indicated that the additional compensation for a shell additive causes the coarsening, resulting in a decrease in sintering density and Pr(remanent polarization). However, coating shell additives to compensate for A site ion is an effective way to suppress volatilization. Based on these experimental results, it would be the biggest advantage to develop an eco-friendly material (Lead-free) that replaced lead (Pb), which is harmful to the human body. This lead-free piezoelectric material can be applied to a biomedical device or products(ex. earphones (hearing aids), heart rate monitors, ultrasonic vibrators, etc.) and skin beauty improvement products (mask packs for whitening and wrinkle improvement).

• Journal of the Korean Society of Radiology
• /
• v.17 no.6
• /
• pp.985-991
• /
• 2023

A tissue-equivalent phantom is necessary for quality control of hyperthermia therapy. However, since there is no phantom for this purpose, phantoms made from agar are being used in various studies. The tissue-equivalent properties of the agar phantom were confirmed by comparison with the tissue-equivalent material bolus in this study. CT images of the agar phantom and bolus were acquired, and tissue equivalent characteristics were analyzed with image analysis and dose calculation using a computerized radiation therapy planning system. The average pixel value was 96.960±10.999 in bolus, 108.559±8.233 in 3% agar phantom, and 111.844±8.651 in 4% agar phantom. Using the SSD technique, 100 cGy was prescribed at a depth of 1.5 cm and 6 MV X -ray was set to irradiated to 10x10 cm2, and the absorbed dose according to depth was calculated from the central axis of the beam. The intraclass correlation coefficient of dose distribution of bolus, 3% agar phantom, and 4% agar phantom was 0.979 (p<.001, 95%CI .957-.991). The density (g/cm3) at the point where the absorbed dose was calculated was 0.990±0.020 at the bolus, 1.018±0.020 at the 3% agar phantom, and 1.035±0.024 at the 4% agar phantom. In this study, the internal density distribution and uniformity of the agar phantom were confirmed to be appropriate as a tissue equivalent material by analysis of CT images and a computerized radiation therapy planning system.

• Progress in Medical Physics
• /
• v.9 no.3
• /
• pp.137-141
• /
• 1998

The purposes of this report are to evaluate whether lead ball and steel ball could be used as protective material of radiation and to acquire physical data of them for protecting 4-10 MV X-ray beams. Lead balls of diameter 2.0～2.5mm or steel balls of diameter 1.5～2.0 mm were filled in an acrylic box of uniform width. An MV radiograph of metal balls in a box were taken to ascertain uniformity of ball distribution in the box. Average density of metal ball and linear attenuation coefficient of metal balls for 4～10 MV X -rays were measured. At the time of measurement of linear attenuation coefficient, Farmer ionization chamber was used and to minimize the scatter effect, distance between the ball and the ionization chamber was 70 cm and field size was 5.5cm${\times}$5.5cm. For comparison, same parameters of lead and steel plates were measured. The distribution of metal balls was uniform in the box. The density of a mixture of lead-air was 6.93g/cm$^3$, 0.611 times density of lead, and the density of a mixture of steel-air was 4.75g/cm$^3$, 0.604 times density of steel. Half-value layers of a mixture of lead-air were 1.89 cm for 4 MV X-ray, 2.07 cm for 6 MV X-ray and 2.16 cm for 10 MV X-ray, and approximately 1.64 times of HVL of lead plate. Half-value layers of a mixture of steel-air were 3.24 cm for 4 MV X-ray, 3.70 cm for 6 MV X-ray and 4.15 cm for 10 MV X-ray, and approximately 1.65 times of HVL of lead plate. Metal balls can be used because they could be distributed evenly. Average densities of mixtures of lead-air and steel-air were 6.93g/cm$^3$, 4.75g/cm$^3$ respectively and approximately 1.65 times of densities of lead and steel. Product of density and HVL for a mixture of metal-air are same as the metal.