• Structural Engineering and Mechanics
• /
• v.65 no.2
• /
• pp.155-162
• /
• 2018

A smart glass fiber reinforced polymer (SMFRP) reinforcing bar with a fiber Bragg grating (FBG) sensor was fabricated using a pultrusion technique, while ribs were formed to improve bonding between concrete and SMFRP. Then, strain of SMFRP bars were measured for a uniaxial tension test of an SMFRP bar, and a four-point bending test of concrete beams reinforced with SMFRP bars. The results of a uniaxial tension test illustrate that the strain obtained from an FBG sensor agrees well with that obtained from electrical resistance strain gauge (ERSG). Additionally, concrete beams reinforced with SMFRP bars were fabricated, and actual flexural test were performed while the strain of with an FBG sensor was compared with that of ERSG. The experimental results demonstrate that SMFRP bars can be used as reinforcement of concrete member while providing deformation information. Furthermore, SMFRP bars may provide stronger durability and smart monitoring to reinforced concrete members under corrosive environments during a service life.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.531-532
• /
• 2009

This paper presents crack spacing which quantitatively considers the fiber distribution and prediction of uniaxial tensile behavior of ECC on the basis of crack spacing and fiber distribution. The predictions exhibit similar tensile stess-strain curves to the test results within 10% error.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.268-273
• /
• 1992

Thin walled tubular specimens of 0.45% structural carbon steel were used in the bizxial tests. Biaxial fatigue tosts were conducted on strain control including fully reversed tension-compression and in phase tension torsion loadings. The predictions of the biaxial fatigue life were based upon the uniaxial low cycle fatigue test results. Fatigue lives were ranged from 10$\^$2/to 10$\^$5/cycles. Four multiaxial strain based theories have been developed to correlate biaxial fatigue experimdntal results. These theories showed good correlatins except for maximum shear strain theory. In uniaxial tests, crack behavior was observed that crack initiated in the maximum shear strain direction and propagated in the direction perpendicular to principal stross. But, in biaxial tests, both crack initiation and growth occured on the maximum shear strain direction only.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.2
• /
• pp.129-138
• /
• 1996

Localization of concrete is a phenomenon such that the deformation of concrete is localized in finite region with softening behavior and it governs ultimate load of concrete. In this Paper, concrete under strain localization was modeled with localization region and non-localization region and lc~calization behavior was formulated based on averaging concept of heterogeneous material. By using the formulation, the localization phenomena of concrete under uniaxial loadings were well predicted. The analytical results show that size of localization region of concrete under uniaxial compression is three times of maximum aggregate size and the size effect of concrete is well predicted. The use of tension-softening curve obtained from direct tension test is suitable for well prediction of localization of concrete under uniaxial tension.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.3
• /
• pp.275-281
• /
• 2011

When a flat bar type metal specimen for general tension test is subject to incremental uniaxial tension, a narrow plastic shear band, so called luders band, is generated at some instance. This band typically has an angle to the axis of specimen and many early researches have been done to investigate the condition and angle of this localized deformation phenomenon by many researchers. This study follows the procedure of Thomas(1961) under plane stress boundary condition. $J_2$ plasticity theory, balance of linear momentum, and constitutive equations are used to derive the angle of luders band under plain strain boundary condition. The result was confirmed by other angle based on acoustic tensor theory.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.315-320
• /
• 2003

Two different strength types of plain concrete plate specimens (200$\times$200$\times$60mm) were tested under different biaxial load combinations. The specimens were subjected to biaxial combinations covering the three regions of compression-compression, compression-tension, and tension-tension. The loading platens with Teflon pads were used to reduce a confining effect in boundary surface between the concrete specimen and the solid platen. The principal deformations in the specimens were recorded, and the failure modes along with each stress ratio were examined. Based on the strength data, the failure envelops were developed for each type of plain concrete. The biaxial stress-strain responses of concrete plate specimens for three biaxial loading regions were also plotted. The test data indicated that the strength of concrete under biaxial compression ($f_2 / f_1$$_1$=-1/-1) is about 17 percent larger than under uniaxial compression.

• Journal of the Korean Society for Railway
• /
• v.10 no.2 s.39
• /
• pp.211-216
• /
• 2007

Rubber components are widely used in many application such as vibration isolators, damping, ride quality. Rubber spring is used in primary suspension system for railway vehicle. Characteristics and useful life prediction of rubber spring was very important in design procedure to assure the safety and reliability. Non-linear properties of rubber material which are described as strain energy function are important parameter to design and evaluate of rubber spring. These are determined by physical tests which are uniaxial tension, equi-biaxial tension and pure shear test. The computer simulation was executed to predict and evaluate the load capacity and stiffness for rubber spring. In order to investigate the useful life, the acceleration test were carried out. Acceleration test results changes as the threshold are used for assessment of the useful life and time to threshold value were plotted against reciprocal of absolute temperature to give the Arrhenius plot. By using the acceleration test, several useful life prediction for rubber spring were proposed.

• International Journal of Railway
• /
• v.1 no.3
• /
• pp.122-127
• /
• 2008

Rubber components are widely used in many application such as vibration isolators, damping, ride quality. Rubber spring is used in primary suspension system for railway vehicle. Characteristics and useful life prediction of rubber spring was very important in design procedure to assure the safety and reliability. Non-linear properties of rubber material which are described as strain energy function are important parameter to design and evaluate of rubber spring. These are determined by physical tests which are uniaxial tension, equi-biaxial tension and pure shear test. The computer simulation was executed to predict and evaluate the load capacity and stiffness for rubber spring. In order to investigate the useful life, the acceleration test were carried out. Acceleration test results changes as the threshold are used for assessment of the useful life and time to threshold value were plotted against reciprocal of absolute temperature to give the Arrhenius plot. By using the acceleration test, several useful life prediction for rubber spring were proposed.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.599-606
• /
• 2003

An analytical model which can simulate the post-cracking nonlinear behavior of reinforced concrete (RC) members such as bars and panels subjected to uniaxial and biaxial tensile stresses is presented. The proposed model includes the description of biaxial failure criteria and the average stress-strain relation of reinforcing steel. Based on strain distribution functions of steel and concrete after cracking, average response of an embedded reinforcement, a criterion to consider the tension-stiffening effect is proposed using the concept of average stresses and strains. The validity of the introduced model is established by comparing the analytical predictions for reinforced concrete tension members with results from experimental studies. Finally, correlation studies between analytical results and experimental data from biaxial tension test are conducted with the objective to establish the validity of the proposed models and identify the significance of various effects on the response of biaxially loaded reinforced concrete panels.

• Structural Engineering and Mechanics
• /
• v.62 no.5
• /
• pp.651-661
• /
• 2017

This paper presents an experimental study of bond-slip behavior of reinforced lightweight aggregate concrete (LC) and normal weight concrete (NC) with embedded steel bar. Tests were conducted on tension-pull specimens that had cross-sectional dimension with a reinforcing bar embedded in the center section. The experimental variables include concrete strength (20, 40, and 60 MPa) and coarse aggregate type (normal-weight aggregate and reservoir sludge lightweight aggregate). The test results show that as concrete compressive strength increased, the magnitudes of the slip of the LC specimens were greater than those of the NC specimens. Moreover, the bond strength and stiffness approaches zero at the loaded end, or close to the central anchored point of the specimen. In addition, the proposed bond stress-slip equation can effectively estimate the behavior of bond stress and steel bar slipping.