• 한국지반공학회논문집
• /
• 제34권10호
• /
• pp.39-49
• /
• 2018

본 연구는 심층혼합시료의 탄성계수를 파악하기 위하여 점토, 모래, 자갈의 입도 구성조건에 안정재 혼합비 8%, 10%, 12%, 14%로 혼합하여 총 320개의 공시체를 제작하였다. 이러한 공시체를 사용하여 일축압축시험을 수행하였고, 일축압축강도와 변형률을 분석하여 할선탄성계수와 접선탄성계수를 구하였다. 실내시험 결과 모든 심층혼합시료는 양생기간과 안정재 혼합비가 증가함에 따라 일축압축강도가 증가하였는데, 이에 대한 할선탄성계수와 접선탄성계수도 증가하는 경향이 뚜렷하게 나타났다. 양생기간에 따른 탄성계수 값의 증가는 할선탄성계수보다 접선탄성계수가 크게 나타났지만, 탄성계수의 증분비는 할선탄성계수가 크게 나타났다. 안정재 혼합비 8%에 대한 탄성계수와 안정재 혼합비 10%, 12%, 14%에 대한 탄성계수 값을 비교하여 안정재 혼합비에 따른 탄성계수를 추정할 수 있는 상관관계식을 공시체 조건별로 구하였다. 심층혼합시료의 입경이 굵어지면 각각의 탄성계수가 증가하는 경향이 나타났으며,가장 큰 영향을 미치는 입경의 분포는 모래질의 구성비가 높을 때 나타났다. 한편 탄성계수증가는 공시체 종류별로는 모래질 공시체가 점토질과 자갈질 공시체보다 크게 나타났다. 이러한 결과를 바탕으로 심층혼합시료의 입도 분포와 안정재 혼합비로 현장의 심층혼합지반의 적절한 지반정수를 제안할 수 있을 것으로 판단된다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.327-333
• /
• 2004

Corestone ground mass has complicated characteristics as it is made up of hard and stiff corestone in a relatively weak and soft matrix. Model corestone ground mass which is physically identical with the stiff corestone in weak matrix were tested in uniaxial compression. The tests show that the increase of the corestone proportion brought the gradual increase of the elastic modulus as well. The ground mass was weaker when the corestone proportion was low while it was stronger in higher corestone proportion. The size of the corestone had no influence on the strength and elastic modulus as long as the proportion of the corestone remains same.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.605-612
• /
• 2002

The objective of this study is to investigate the behavior of Visco-Elasto-Plastic materials of Silicate Grouted Sands due to external load. Uniaxial compression strength of silicate grouted sands was increased accordingly with curing time, but it was almost unchanged after 7days. A series of uniaxial compression creep tests were peformed for $\sigma$/$\sigma$$\sub$f/ = 8%,16% and 24%. The tested Silicated Grouted Sands exhibits three types of strains : elastic, plastic, viscoelastic. It is seen that the magnitude of the instantaneous recoverable strains $\varepsilon$$\sub$r/(o) is approximately independent of the unloading time. In this tests, The total creep strains( elastic, plastic, viscoelastic) are proportional to the stress level. Based on the constant creep test results, relationships between the time and the creep compliance are developed.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1487-1493
• /
• 2008

The frost heaving is related with thermal conduction rate and permeability. If the thermal conduction rate can be controlled, it is effective to prevent from frost heaving. If soil mixed with shredded tire which has relatively lower thermal conduction rate than soil, it helps preventing from frost heaving. However, in this case, the shear strength can get weak. In this study, we compared thermal conduction rate of soil and shredded tire, and test uniaxial compression strength of soil which is mixed with shredded tire and cement in different ratio.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.655-662
• /
• 2003

Slope stability is an important issue ill civil engineering works or in open pit mines where both economy and efficiency is required. These are the long-term stability problems which depend on the change of physical properties under a certain weather condition. These can also result in progress of weathering which can change mechanical or hydro-geological properties of rock mass considerably. In this study, weathering in nature was simulated by freeze-thaw test and Soxhlet test which represent mechanical and chemical weathering respectively. Measured were elastic wave velocities, absorption rate, volume change. Uniaxial compression strengths before and after the weathering tests were also measured. The change in weight and volume of the specimens were not clearly related to the weathering process, but P, S wave velocities were clearly decreased as weathering progresses. For some class of rocks, P-wave velocity was increased probably because of the saturation due to improved connectivity of the pre-existing pores. Based on the test results, stability of the slopes were analyzed using FLAC$\^$2D/. Due to the reduced strength parameters, the factors of safety were decreased for the selected sites.

• 한국해양공학회지
• /
• 제20권1호
• /
• pp.7-15
• /
• 2006

In this research, the behavior characteristics of cement mixing lightweight soil (CMLS) for recycling of dredged soil in the Nakdong River estuary are experimentally investigated. CMLS is composed of the dredged soil from Nakdong River estuary, cement, and air foam. For this purpose, uniaxial compression tests are carried out for artificially prepared specimens of CMLS, with various initial water contents, cement contents, and mixing ratio of dredged soils. The experimental results of CMLS indicated that the compressive strength is strongly influenced by the cement contents, rather than water contents and air foam. Compressive strength of CMLS increased with an increase in cement content, while it decreased with an increase in water content and air foam content. It was also found that the modulus of deformation E50 was in a range of 44 to 128 times greater than the value of uniaxial compressive strength, cured in 28 days.

• 터널과지하공간
• /
• 제11권4호
• /
• pp.301-310
• /
• 2001

열 여섯개의 절리 면을 가진 석고 시편을 제작, 일축 압축 실험을 하여 관측된 결과를 절리 면이 두 개 및 세개 가진 시편의 실험 결과와 비교하였다. 그 결과 다중 절리면(열여섯 면)에서 관측된 익형(翼形)크랙, 이차 크랙, 연절리 (連節理) 유형은 절리가 두 개 및 세 개를 가진 시험체와 비슷한 형상을 보였다. 익형 크랙은 절리면과 일정한 각도를 유지한 상태에서 시작하여 안정적으로 진전, 최대 압축응력 방향으로 발달하였으며 이차 크랙 또한 안정적인 진전 양상을 보였으나 높은 하중 상태에서 이차 크랙은 불안정한 진전을 보이며 연절리 현상을 보였다. 이차 크랙의 종류로는 유사 공면(共面) 및 사면(斜面) 이차 크랙이 관측되었다. 연절리 현상은 익형 크랙과 이차 크랙에 의한 절리면의 연결로 나타나며 본 실험에서 네 종류의 연절리 현상이 관측되었다. 관측된 연절리의 발생 형태, 익형 크랙 및 이차 크랙의 초기 발생 응력은 절리면의 간격, 연속성, 경사각, 단선(短線)각도와 절리면의 배열과 관련이 있다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.501-506
• /
• 1999

The purpose of this study is to experimentally investigate the strength and ductility of reinforced high strength concrete columns under uniaxial load and several test variables. To do this, we have conducted tests on thirteen 20$\times$20$\times$60cm specimens with 8 and 12 longitudinal steel bars subjected to monotonic uniaxial compression. The main variables considered in this test are the configuration of ties, the space the ties, the diameter of ties and yield strength of ties. The results indicate that the strength and the ductility of reinforced high strength concrete columns have been influenced on these variables except yield strength of ties. Judging from test results, real stress of ties at peak concrete stress is suitable variable than yield strength of ties for estimation of the strength gain factor(Ks).

• 한국초전도ㆍ저온공학회논문지
• /
• 제20권4호
• /
• pp.31-35
• /
• 2018

When REBCO coated conductors (CCs) are applied to superconducting devices such as coils and magnets, they are subjected to deformation in various modes such as compression/tension bending, uniaxial/transverse tension and torsion. Despite outstanding performances by REBCO CC tapes, their electromechanical properties have been evaluated primarily under uniaxial tension, therefore data about the critical current ($I_c$) response in the compressive strain region are lacking. In this study, the characteristic responses of $I_c$ in REBCO CC tapes under bending strains in the range from tensile to compressive were evaluated. The springboard bending beam was used, wherein the CC tape sample was soldered onto the surface of the springboard. A Goldacker-type bending test rig, which lacks a support holding the sample during testing, was used as a comparator. Degradation in $I_c$ behaviors, including strain sensitivity, in differently processed REBCO CC tapes were examined based on the test rig used.

• Smart Structures and Systems
• /
• 제22권6호
• /
• pp.643-662
• /
• 2018

One of the methods for investigation of mechanical behavior of materials is numerical simulation. For simulation, its need to model behavior is close to real condition. PFC is one of the rock mechanics software that needs calibration for models simulation. The calibration was performed based on simulation of unconfined compression test and Brazilian test. Indeed the micro parameter of models change so that the UCS and Brazilian test results in numerical simulation be close to experimental one. In this paper, the effect of four micro parameters has been investigated on the uniaxial compression test and Brazilian test. These micro parameters are friction angle, Accumulation factor, expansion coefficient and disc distance. The results show that these micro parameters affect the failure pattern in UCS and Brazilian test. Also compressive strength and tensile strength are controlled by failure pattern.