• Geomechanics and Engineering
• /
• v.29 no.3
• /
• pp.281-290
• /
• 2022

The direct shear test is commonly used to evaluate the shear behavior of frozen soil-structure interfaces under normal stress. However, failure criteria, such as the Mohr-Coulomb failure criterion, are needed to obtain the unconfined shear strength. Hence, the punch shear test, which is usually used to estimate the shear strength of rocks without confinement, was examined in this study to directly determine the adfreezing strength. It is measured as the shear strength of the frozen soil-structure interface under unconfined conditions. Different soils of silica sand, field sand, and field clay were prepared inside the steel and concrete ring structures. Soil and ring structures were frozen at the target temperature for more than 24 h. A punch shear test was then conducted. The test results show that the adfreezing strength increased with a decrease in the target temperature and increase in the initial water content, owing to the increase in ice content. The adfreezing strength of field clay was the smallest when compared with the other soil specimens because of the large amount of unfrozen water content. The field sand with the larger normalized roughness showed greater adfreezing strength than the silica sand with a lower normalized roughness. From the experiment and analysis, the applicability of the punch shear test was examined to measure the adfreezing strength of the frozen soil-structure interface. To find a proper sample dimension, supplementary experiments or numerical analysis will be needed in further research.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.3
• /
• pp.67-75
• /
• 2012

This paper presents an environment-friendly sand cementation method by precipitating calcium carbonate using plant extracts. The plant extracts contain urease like $Sporosarcina$ $pasteurii$, which can decompose urea into carbonate ion and ammonium ion. It can cause cementation within sand particles where carbonate ions decomposed from urea combine with calcium ions dissolved from calcium chloride or calcium hydroxide to form calcium carbonate. Plant extracts, urea and calcium chloride or calcium hydroxide were blended and then mixed with Nakdong River sand. The mixed sand was compacted into a cylindrical specimen and cured for 3 days at room temperature ($18^{\circ}C$). Unconfined compression test, SEM and XRD analyses were carried out to evaluate three levels of urea concentration and two different calcium sources. As urea concentration increased, the unconfined compressive strength increased up to 10 times those without plant extracts because calcium carbonate precipitated more, regardless of calcium source. It was also found that the strength of specimen using calcium chloride was higher than that of specimen using calcium hydroxide.

• Geomechanics and Engineering
• /
• v.12 no.3
• /
• pp.441-464
• /
• 2017

The determination of the mixture parameters of stabilization has become a great concern in geotechnical applications. This paper presents an effort about the application of artificial intelligence (AI) techniques including radial basis neural network (RBNN), multi-layer perceptrons (MLP), generalized regression neural network (GRNN) and adaptive neuro-fuzzy inference system (ANFIS) in order to predict the unconfined compressive strength (UCS) of silty soil stabilized with bottom ash (BA), jute fiber (JF) and steel fiber (SF) under different freeze-thaw cycles (FTC). The dosages of the stabilizers and number of freeze-thaw cycles were employed as input (predictor) variables and the UCS values as output variable. For understanding the dominant parameter of the predictor variables on the UCS of stabilized soil, a sensitivity analysis has also been performed. The performance measures of root mean square error (RMSE), mean absolute error (MAE) and determination coefficient ($R^2$) were used for the evaluations of the prediction accuracy and applicability of the employed models. The results indicate that the predictions due to all AI techniques employed are significantly correlated with the measured UCS ($p{\leq}0.05$). They also perform better predictions than nonlinear regression (NLR) in terms of the performance measures. It is found from the model performances that RBNN approach within AI techniques yields the highest satisfactory results (RMSE = 55.4 kPa, MAE = 45.1 kPa, and $R^2=0.988$). The sensitivity analysis demonstrates that the JF inclusion within the input predictors is the most effective parameter on the UCS responses, followed by FTC.

• Journal of the Korean GEO-environmental Society
• /
• v.6 no.4
• /
• pp.5-12
• /
• 2005

In this study, the geotechnical applicability of permeable barriers that could filter the leachate from a landfill was evaluated. Specimens were cast from sand, loess and bentonite according to the specific weight ratios of them. A series of experiments are performed to determine the unconfined compressive strength and permeability of various mixing ratio of bentonite, loess, and sand. From the laboratory test, optimum mixing ratio that satisfied the regulations of unconfined compressive strength($5kgf/cm^2$) and coefficient of permeability ($10^{-3}{\sim}10^{-4}cm/sec$) in landfill was found when the weight ratio of sand and loess was 8:2 with 2% of bentonite. Using the laboratory test data and in situ test results, the applicability of the wall will be tested for various conditions.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09c
• /
• pp.129-134
• /
• 2010

This paper investigates effects of rubber inclusion on the strength and physical characteristics of rubber.added composite geomaterial (CGM) in which dredged soils, crumb rubber, and bottom ash are reused for recycling. Several series of test specimens were prepared at 5 different percentages of rubber content (i.e. 0%, 25%, 50%, 75%, and 100% by weight of the dry dredged soil) and three different percentages of bottom ash content (i.e. 0%, 50% and 100% by weight of the dry dredged soil). The mixed soil specimens were subjected to unconfined compression test and elastic wave test to investigate their unconfined compressive strengths and small strain properties. The values of bulk unit weight of the CGM with bottom ash content of 0% and 100% decrease from 14kN/$m^3$ to 11kN/$m^3$ and 15kN/$m^3$ to 12kN/$m^3$, respectively, as rubber content increases, because the rubber had a specific gravity of 1.13. The test results indicated that the rubber content and bottom ash content were found to influence the strength and stress-strain behavior of CGM. Overall, the unconfined compressive strength, and shear modulus were found to decrease with increasing rubber content. Among the samples tested in this study, those with a lower rubber content exhibited sand-like behavior and a higher shear modulus. Samples with a higher rubber content exhibited rubber-like behavior and a lower shear modulus. The CGM with 100% bottom ash could be used as alternative backfill material better than CGM with 0% bottom ash. The results of elastic wave tests indicate that the higher rubber content, the lower shear modulus (G).

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2C
• /
• pp.95-107
• /
• 2010

To calculate the end bearing capacity of a drilled Shaft socketed into the rockmass, the unconfined compression strength could be used. But it is difficult to find the unconfined compression strength because it is impossible to get undisturbed samples in weathered soils and rocks. So, to calculate the end bearing capacity, the existing bearing formula could not be used. In this study, for five zones (near pile tip, tip~lower 1D, tip~lower 2D, upper 1D~lower 1D, upper 1D~lower 2D), the relationships between the characteristic values of in-situ tests(SPT, DCPT PMT, BST) and the end bearing capacity of drilled shafts were analysed. As a result, DCPT results were represented the best credibility. Also, a design chart of end bearing capacity using DCPT was suggested.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.4
• /
• pp.5-12
• /
• 2010

Soil mixture using bentonite as a cutoff material is used a lot for various structures such as landfills, banks and dams as cutoff materials. But seepage water is expected to seep since shear failure of filter layer occurs due to external load, embankment load when constructed. Generally, only coefficient of permeability of Soil Mixture is considered irrespective of the changes of intensity on amount of additives. This research is to study on how the changes of amount of bentonite affects permeability and strength of soil mixture. So successive experiments for measuring permeability and strength were conducted as the amount of bentonite changes from 0 to 4%, mixing with the bed material and then making specimens. Around construction site of B dam. As a result, 2.085E-07 cm/sec was shown when the amount of Soil Mixture was 4%. It is proved that unconfined compressive strength and tensile strength increase as the amount of bentonite increases, but saturation shear strength of bentonite soil mixture from the CD experiment is hardly influenced by the amount of bentonite.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.63 no.6
• /
• pp.17-26
• /
• 2021

Greenhouses have been damaged due to the uplift pressure from strong wind, for which rebar piles are often installed near the greenhouse to resist the pressure. For the effective design of rebar piles, it is necessary to access the shear strength of soil on which the greenhouse is constructed. This study experimentally evaluates the shear strength of the soil beneath the greenhouse. Four soil samples were collected from four agricultural sites, and prepared for testing with 75, 80, 85, and 90% compaction rates. One-dimensional unconfined compression test (UC), consolidated-undrained triaxial test (CU), and resonant column test (RC) were performed for the evaluation of shear strength and shear modulus. Generally, the higher shear strength and modulus were observed with the higher compaction rates. In particular, the UC shear strength increases with the increase of #200 sieve passing rate. Resulting from the CU test, the sample with the most of coarse soil had the highest friction angle, but the variation is small among samples. Resulting from the CU and RC tests, the ratio of maximum shear modulus with the major principle stress at failure was the higher at the finer soil. The ratio was two to three times greater than the ratio from the standard sand. This indicates that the shear strength is lower for the fine soil than the coarse soil at the same shear modulus. The results of this study will be a useful resource for the estimation of the pull-out strength of the rebar pile against the uplift pressure.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.4
• /
• pp.35-42
• /
• 2023

This paper described the strength variation characteristics to evaluate the applicability of a reactive material that can absorb organic pollutants as an underground barrier. The Strength was evaluated by unconfined compression test. The test results showed that the strength of the reactive material according to the absorption of each pollutant was in the order of water > TCE > TPH. However, the strength of the reactive material absorbing TPH was greater than that of the case absorbing TCE, when the composition ratio of polynorbornene was 12% or less. The strength of the reaction material in contact with water continued to decrease as the polynorbornene composition ratio decreased. The strength of the reaction material in contact with TCE and TPH increased as the polynorbornene composition ratio decreased from 30% to 21%, and then decreased. In other words, the optimal composition ratio of the reactive material should be applied considering the strength due to contact with pollutants according to the stress conditions occurring in the ground.

• Journal of the Korean GEO-environmental Society
• /
• v.16 no.2
• /
• pp.15-25
• /
• 2015

As the physical and mechanical properties of lightweight air-mixed soil change in the procedure of transportation of mix truck, it is necessary to assure whether the properties during construction satisfy those in design. In this study, variations of properties of mixed soil after transportation by mix truck are proved by field test. Lightweight air-mixed soil used field test the unit weight of $9.0{\pm}1.0kN/m^3$, the flow value of $190{\pm}20mm$ was produced. To analyze variations of properties of mixed soil the unit weight and flow value of the sample before and after transport was measured unconfined compressive strength tests were performed. Mixing time was 19~175 minutes diversified. As the test results, it is known that the density, the flow value and the unconfined compressive strength of lightweight air-mixed soil change by transportation, but these values satisfy the specifications of material of air-mixed soil. After transportation the average value of the unit weight and flow value change in the flow of the $(+)0.10kN/m^3$, 4.8 mm respectively, the average change in the unit weight and the flow value due to the mixing time was constant. And unconfined compressive strength of 28-day specimen increases from 20 to $150kN/m^2$. But, these values do not have some clear relationship with the transportation time within 175 minutes which is longest test time. Consequently, Within 175 minutes the changes of properties by transportation are too small to show some problems in the construction field.