• Tribology and Lubricants
• /
• v.33 no.1
• /
• pp.9-14
• /
• 2017

This paper presents a rotordynamic analysis and the operation of a power turbine applied to a 250 kW super-critical $CO_2$ cycle. The power turbine consists of a turbine wheel and a shaft supported by two fluid film bearings. We use a tilting pad bearing for the power turbine owing to the high speed operation, and employ copper backing pads to improve the thermal management of the bearing. We conduct a rotordynamic analysis based on the design parameters of the power turbine. The dynamic coefficients of the tilting pad bearings were calculated based on the iso-thermal lubrication theory and turbine wheel was modeled as equivalent inertia. The predicted Cambell diagram showed that there are two critical speeds, namely the conical and bending critical speeds under the rated speed. However, the unbalance response prediction showed that vibration levels are controlled within 10 mm for all speed ranges owing to the high damping ratio of the modes. Additionally, the predicted logarithmic decrement indicates that there is no unstable mode. The power turbine uses compressed air at a temperature of $250^{\circ}C$ in its operation, and we monitor the shaft vibration and temperature of the lubricant during the test. In the steady state, we record a temperature rise of $40^{\circ}C$ between the inlet and outlet lubricant and the measured shaft vibration shows good agreement with the prediction.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.425-432
• /
• 2011

In tilting pad bearing design process, the selection of the proper configuration type of either a Load-Between-Pad (LBP) or Load-On-Pad (LOP) as well as preload and pivot offset conditions is to be carefully considered. Also the bearing needs to be designed in order to be suited for the rotor-bearing system and operating condition. In this paper, it is observed that the dynamic characteristics in a 5 pad tilting pad bearing for the LBP and the LOP configurations are influenced by the variation of preload and pivot offset. In this context, rotor dynamic analysis of the 5MW industrial gas turbine supported by the tilting pad bearing at the front and roller bearing at the rear is carried out based on the dynamic coefficients of the tilting pad bearing investigated. The result shows that two rigid body critical modes experience various changes according to the influence of the tilting pad bearing uniquely applied to one side of this machine. Mainly, the second critical speed, the rigid body mode of conical shape with high whirling in the tilting pad bearing, is significantly changed by preload and pivot offset regardless of the LBP and LOP configurations. And, the first critical mode, the rigid body mode of conical shape with high whirling in the roller bearing, is sensitively affected by preload applied to the LOP configuration and by the its asymmetric dynamic properties.

• Journal of the East Asian Society of Dietary Life
• /
• v.24 no.5
• /
• pp.552-563
• /
• 2014

This study was performed to investigate the dietary habits and nutritional knowledge of elementary school students (boy : 250, girl : 250) by gender. Frequency of skipping breakfast was high in both boys and girls. Duration of mealtime was significantly higher for boys compared with girls (p<0.001). Regularity of meals was not significantly different between boys and girls. Reason for irregular meals was 'no appetite' for both boys (39.6%) and girls (40.0%). Unbalanced diet was high in both boys (60.8%) and girls (59.6%), and problems related to dietary habits were in order of 'unbalance diet', 'irregular mealtime', 'overeating', 'skip a meal frequently', and 'eat out frequently'. Frequency of snack intake was significantly higher for girls compared to boys(p<0.05). The criterion for selecting snacks was higher for 'nutrition' compared to 'good taste' for both boys and girls. Frequency of eating out was statistically insignificant, and eating out preferences were in the order of 'Korean food', 'western food', and 'Chinese food'. Eating behavior 'eat meat, fish, egg, tofu every meal' was significantly higher for boys compared to girls (p<0.01). 'Healthful' response rates were 57.6% for boys and 58.8% for girls. Practice level of nutritional knowledge was significantly higher in girls compared to boys (p<0.001). To establish good eating behaviors, we should develop systematic and continuous education programs.

• Journal of the Korean Vacuum Society
• /
• v.19 no.4
• /
• pp.256-264
• /
• 2010

In this paper, a digital controller of magnetic bearing system for a high vacuum turbomolecular pump (TMP) is designed and examined. For stabilizing and providing damping in magnetic bearing, the digital PID controller is applied for each 5 control axes, and the inter-axis cross feedback controller is also applied to suppress low frequency vibration caused by gyroscopic moment of the rotor at high speed of rotation. The fabricated rotor-shaft has its first flexible natural frequency lower than maximum speed, about 614Hz, so the two lead filters are applied to increase damping of flexible mode. Notch filters with rotating frequency were selected to reduce vibration of the pump housing caused by unbalance load. The implemented controllers are verified by examination of frequency response and rotating test up to 40,000 rpm, which is higher than critical speed of backward flexible mode.

• The KIPS Transactions:PartA
• /
• v.12A no.2 s.92
• /
• pp.151-160
• /
• 2005

The exponential growth of Web users requires the web serves with high expandability and reliability. It leads to the excessive transmission traffic and system overload problems. To solve these problems, cluster systems are widely studied. In conventional cluster systems, when the request size is large owing to such types as multimedia and CGI, the particular server load and response time tend to increase even if the overall loads are distributed evenly. In this paper, a cluster system is proposed where each Web server in the system has different contents and loads are distributed efficiently using the Web server resource information such as CPU, memory and disk utilization. Web servers having different contents are mutually connected and managed with a network file system to maintain information consistency required to support resource information updates, deletions, and additions. Load unbalance among contents group owing to distribution of contents can be alleviated by reassignment of Web servers. Using a simulation method, we showed that our method shows up to $50\%$ about average throughput and processing time improvement comparing to systems using each LC method and RR method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.9
• /
• pp.925-932
• /
• 2014

If a rotor possesses a high gyroscopic coupling or the running speed is high, the dynamical changes in the rotor become prominent. When active magnetic bearings are used to support such rotors, it is necessary for the bearing controller to take these dynamical changes into consideration. Independent-axis controllers, which are the most commonly used, modulate the bearing force solely based on the sensor output of the same axis. However, this type of controller has difficulties in overcoming the dynamical changes. On the other hand, mixed-axis controllers transform the sensor output into components corresponding to the vibrational modes. A separate controller can then be designed for each vibrational mode. In this way, the controller can be designed based on the dynamics of the rotor. In this paper, we describe a design process for a mixed-axis controller that uses a detailed mathematical model of the system. The performance of the controller is evaluated based on the ISO sensitivity requirements and unbalance response, while considering the change in the system dynamics due to the running speed.