• 한국환경과학회지
• /
• 제24권9호
• /
• pp.1181-1188
• /
• 2015

In this study, we discussed about the application of the single physical and chemical treatment processes and the physical-chemical complex treatment processes on the inactivation of Artemia sp. in order to satisfy the USCG Phase II (United States Coast Guard). The results showed that initial disinfection rate of ultrasonic process in single batch process is higher than that of electrolysis. However, the inactivation rate showed slower than electrolysis. The inactivation rate of Artemia sp. on the single continuous treatment process ranked in the following order: homogenizer > electrolysis > ultrasonic process. Inactivation rate of Artemia sp. in continuous homogenizer-electrolysis complex process was reached at 100% immediately. A synergistic effect of ultrasonic-electrolytic complex process was found to be a small. The order of processes in a complex process did not affect the disinfection performance.

• 산경연구논집
• /
• 제9권12호
• /
• pp.23-29
• /
• 2018

Purpose - The purpose of this study is to apply a cost effective ultrasonic odor reduction method that generated micro-bubbles using ejector to the Southeast Asian wastewater market. Research design, data, and methodology - A leather maker located in Ansan-city, Gyunggi-do, South Korea was sampled from the collection tank to select experimental materials. Experimental setup consisted of circulating water tank-air ejector-ultrasonic device, and circulating wastewater. Sample analysis was performed by CODcr, T-N, T-P, and turbidity by the National Environmental Science Institute. Results - Experimental results show that it is most effective in removing odors when the frequency range of ultrasonic wave is 60~80 Khz and the output is 200 W. It showed that the concentration of complex odor dropped from a maximum of 14,422 times to a minimum of 120 times. Also, analysis of ammonia and hydrogen sulfide in specific odor substances has shown that they were reduced from 1.5 ppm to 0.4 ppm and from 0.6 ppm to 0.1 ppm, respectively. Conclusions - It is possible to shorten more than 12 hours in the treatment of micro-organisms. It can be seen that the processing time of odor after ultrasonic treatment in the pre-treatment facility is reduced by 25% when compared to the resultant micro-organisms after the chemical treatment, that is, the time of the bio-treatment of micro-organisms. Based on the results, it was confirmed that the pre-treatment method using the ultrasonic and the air ejector device of the experiment shows the effect of reducing the water pollutants and odor more effectively in a relatively short time than the conventional advanced oxidation method.

• 한국축산식품학회지
• /
• 제22권2호
• /
• pp.115-121
• /
• 2002

본 연구는 초음파 처리시간이 튀김 계육의 품질 및 기호성에 미치는 영향을 검토하기 위하여 실시하였다. 수분함량의 경우 가슴육 및 다리육 모두 U-10 처리구가 대조구보다 낮았으며, 단백질 함량은 대조구와 초음파 처리구 사이에 차이가 없었다. 지방함량은 초음파 처리시간이 길어질수록 높아졌다. 튀김감량은 초음파 처리구가 대조구보다 낮았으며, 보수력은 초음파 처리시간이 길어질수록 대조구보다 높아지는 경향이었다. 그리고 물리적인 조직감은 대조구와 초음파처리구 사이에 현저한 차이가 없었다. L*(명도)값은 대조구와 초음파 처리구 사이에 차이가 없었으나, 가슴육이 다리육보다 높았다. 그리고 a*(적색도)값은 초음파처리에 의한 영향은 없었으나 다리육이 가슴육보다 높았다. 구성아미노산은 glutamic acid, aspartic acid, lysine, leucine 및 arginine이 많이 함유되어 있었다. 지방산 조성은 oleic acid와 linoleic acid가 약 60% 이상을 차지하였다. 그리고 맛, 조직감, 다즙성 및 전체적인 기호성은 초음파 처리시간에 따라 향상되었다.

• 환경위생공학
• /
• 제11권2호
• /
• pp.33-41
• /
• 1996

This study was performed to examine the factors influencing on the degradation of TCE, Benzene and 2,4 DCP in aqueous solution using ultrasonic irradiation. The TCE,Benzene and 2,4 DCP, which are hazard compounds causing environmental pollution, were not decomposable pollutants by convientional treatment. The results shows that the generation of H$_{2}$O$_{2}$, H$^{+}$ and OH$^{-}$ radical was formed by the oxidation and reduction reaction of ultrasound, and then theses decomposed the refractory pollutants of TCE, Benzene & 2,4 DCP in aqueous solution. we conformed that the ultrasonic irradiation was excellent in removal efficiency of the refractory pollutants any other than Advanced Oxidation Processes(AOP), utilized the treatment of organic compounds in the industrial wastewater. Consequently, these results suggest that ultrasonic irradiation may be extremely useful for the treatment of wastewaters contaminated organic pollutants, which is difficult to treat economically by conventional process.

• 유기물자원화
• /
• 제16권3호
• /
• pp.83-90
• /
• 2008

하수슬러지의 초음파 전처리시 용존성 유기물의 증가와 혐기성 생분해도 향상을 평가하였다. 하수슬러지의 초음파에 의한 가용화는 세포벽의 파괴로 인하여 용해성 화학적 산소요구량, 단백질 및 탄수화물의 농도 증가와 입자크기를 감소시켰다. 혐기성 생분해도 측면에서초음파 전처리는 메탄가스 발생량을 증가시켜 혐기성 생분해를 향상시키는 것으로 나타났다. 하수슬러지의 생화학적 메탄 잠재 발생량 실험결과 초음파 전처리 후 슬러지의 최종 메탄 수율은 294.3 ml $CH_4/gVS$로 나타나 전처리를 하지 않은 경우 211.3 ml $CH_4/gVS$에 비해 약 40 % 향상된 값을 보였다. 이와 같은 결과를 고려 시 하수슬러지의 가용화는 혐기성 생분해도 향상에 효과적인 것으로 나타났다.

• Journal of Electrical Engineering and Technology
• /
• 제11권5호
• /
• pp.1337-1341
• /
• 2016

• 한국주조공학회지
• /
• 제43권4호
• /
• pp.203-209
• /
• 2023

• Macromolecular Research
• /
• 제16권5호
• /
• pp.411-417
• /
• 2008

The surfaces of henequen fibers, which can be obtained from the leaves of agave plants, were treated with two different media, tap water and sodium hydroxide, that underwent both soaking and ultrasonic methods for the fiber surface treatment. Various biocomposites were fabricated with untreated and treated, chopped henequen fibers and polypropylene using a compression molding method. The result is discussed in terms of interfacial shear strength, flexural properties, dynamic mechanical properties, and fracture surface observations of the biocomposites. The soaking (static method) and ultrasonic (dynamic method) treatments with tap water and sodium hydroxide at different concentrations and treatment times significantly influenced the interfacial, flexural and dynamic mechanical properties of henequen/polypropylene biocomposites. The alkali treatment was more effective than the water treatment in improving the interfacial and mechanical properties of randomly oriented, chopped henequen/PP bio-composites. In addition, the application of the ultrasonic method to each treatment was relatively more effective in increasing the properties than the soaking method, depending on the treatment medium and condition. The greatest improvement in the properties studied was achieved by ultrasonic alkalization of natural fibers, which was in agreement with the other results of interfacial shear strength, flexural strength and modulus, storage modulus, and fracture surfaces.

• International Journal of Internet, Broadcasting and Communication
• /
• 제10권2호
• /
• pp.45-50
• /
• 2018

Recently the water management department advised the water treatment industry to focus on deploy the chemical free and the environmentally responsible process to adopt on water treatment plants in every country. In this objective, water treatment process started using ultrasonic based phycocyanin extraction with fluorescence measurement techniques to detect the change in the yield of phycocyanin. This paper propose the design of optical filter model for fluorescence technique based immersive optical phycocyanin measurement sensor design. The proposed design uses the multi-wavelength sensor module for irradiating part, and this plays a role of removing a wavelength band other than 590 ~ 620 nm. The preliminary study on immersed phycocyanin sensor, the fluorescence value of picocyanin according to the ultrasonic intensity, treatment time and number of cells was measured using JM phycocyanin module to emulate the proposed design, and were compared performance of the proposed sensor emulation. In this design, the phycocyanin fluorescence value increased about 2.1 ~ 4.7 times as the ultrasonic treatment time increased as compared with JM phycocyanin module, and the phycocyanin fluorescence value within the analysis range was obtained by ultrasonic treatment within one minute.

• 한국표면공학회지
• /
• 제34권6호
• /
• pp.545-552
• /
• 2001

Effect of ultrasonic agitation on Pd catalyst treatment was studied in metallization of ceramic boards by Cu electroless plating method.96% $Al_{2}$$O_{3}$ ceramic boards were used as substrate. In this study, the ultrasonic frequency of 28kHz was applied. In Pd catalyst, high density Pd nuclei of small size were formed during ultrasonic agitation. Density of Pd was more improved when using of ultrasonic then no stirring. In electroless plating, plating rate was in the range of 0.6~1.8$\mu\textrm{m}$/hr, which value increased with Rochelle Salts addition. Adhesion strength between ceramic boards and Cu layer was improved of 20% when using ultrasonic agitation at $30^{\circ}C$ ,5min.