• 한국구조물진단유지관리공학회 논문집
• /
• 제24권6호
• /
• pp.25-33
• /
• 2020

취성재료의 변형률 분포와 인장물성과의 상관관계를 분석하기 위해 변형률 분포를 가지도록 탭부분을 변형한 5개 타입-S0, SD1, SD2, SV1, SV2 - 의 탄소섬유보강폴리머(CFRP) 인장시편군을 시험하였다. 변형률 분포가 큰 SD2, SV2 의 극한응력 및 변형률이 SD1, SV1 보다 작게 나타났는데, 이는 비대칭 형상의 SD타입보다 대칭 형상의 SV의 시험결과에서 더 분명하게 나타냈다. 더불어 본 연구에서 사용한 변형률 분포를 가진 대부분의 시편의 극한 응력 및 변형률은 변형률 분포가 없는 대조군과 비교하였을 때 감소하였다. 이러한 결과는 1) 변형률계를 통해 직접 계측한 변형률의 평균값, 2) 전체변형량을 유효길이로 나눠 산정하는 환산변형률, 3) 탄성계수와 극한하중으로부터 유도하는 (극한)유효변형률을 통해 다각적으로 분석되었다. 변형률계에서 계측된 값은 국소구간 응답을 정확히 나타내지만, 전단면의 응답을 표현하는 것은 아니다. 반면, 환산변형률과 유효변형률은 전단면의 평균거동을 나타내므로, 게이지의 단점을 보완할 수 있다. 특히 유효변형률은 극한하중 부근에서 변형률계 측정값이 게이지 손상이나 비정상적 계측값 등의 원인으로 유효하지 않을 때도 실무적으로도 사용할 있는 보수적인 파단변형률을 산정할 수 있다. 이 값은 부분파단이 발생한 경우에도 사용할 수 있으며, 변형률 분포를 가지는 시편에서 합리적으로 유용하다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.334-337
• /
• 2007

Austenitic stainless steel is used as high temperature components such as gas turbine blade and disk because of its good thermal resistance. In the present investigation, tensile and low cycle fatigue(LCF) behavior of stainless steel for turbine disks was studied at wide temperature range $20^{\circ}C\;{\sim}\;750^{\circ}C$. In the tensile tests, it was shown that elastic modulus, yield strength, ultimate tensile strength decreased when temperature increased. The effect on fatigue failure of the parameters such as plastic strain amplitude, stress amplitude and plastic strain energy density was also investigated. Coffin-Manson and Morrow models were used to adjust experimental data and predict the fatigue life behavior at different mean strain values during cyclic loading of high temperature components.

• 한국강구조학회 논문집
• /
• 제15권2호
• /
• pp.137-145
• /
• 2003

본 연구에서는 국산 PS 강봉의 직경, 반복최소응력 및 반복최대응력 등을 실험변수로 하여 직접 인장 피로실험을 수행하였다. 정적 인장실험 결과, 국산 PS 강봉의 응력 - 변형률 곡선과 극한강도 등을 얻었다. 또한, 피로실험에서의 특징적인 실험결과는 PS 강봉의 직경은 피로 수명에 중요한 인자가 아니며, 반복 최소응력의 크기는 국산 PS 강봉의 피로수명에 매우 큰 영향을 미치는 것으로 나타났다. 이러한 피로실험결과를 통계 분석하여 PS 강봉의 응력 범위 및 반복 최소응력 등을 변수로 하는 피로강도 예측식을 제안하였다. 피로실험 중, 시편중앙에 설치한 Extensometer를 이용하여, 변형률의 변화를 측정하였으며, 측정된 변형률 변화현상에서 탄성계수의 변화현상을 구하였다. 변형률 증가현상은 3단계의 형태 즉, 초기에 급격한 증가 후 서서히 증가하며 파괴 직전에 급격하게 증가하는 형태로 나타났다. 탄성계수의 변화현상은 변형률 변화현상과 유사하게 감소하는 것으로 나타났으며 응력수준은 탄성계수 변화에 큰 영향을 주지 않는 것으로 나타났다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제6권2호
• /
• pp.157-165
• /
• 2002

Nonlinear analysis of the reinforced concrete beam subjected to torsion is presented. Seventeen equations involving seventeen variables are derived from the equilibrium equation, compatibility equation, and the material constitutive laws to solve the torsion problem. Newton method was used to solve the nonlinear simultaneous equations and efficient algorithms are proposed. Present model covers the behavior of reinforced concrete beam under pure torsion from service load range to ultimate stage. Tensile resistance of concrete after cracking is appropriately considered. The softened concrete truss model and the average stress-strain relations of concrete and steel are used. To verify the validity of present model, the nominal torsional moment strengths according to ACI-99 code and the ultimate torsional moment by present model are compared to experimental torsional strengths of 55 test specimens found in literature. The ultimate torsional moment strengths by the present model show good results.

• 한국생산제조학회지
• /
• 제9권4호
• /
• pp.25-33
• /
• 2000

The reorientations of the atoms by frictional shear deformation at the surface induce cracks at the boundary of the grain. The cracks grow and propagate in regions where the hydrostatic component of stress is least compressive because the compressive component restores the cracks by three-dimensional crystallizing $\pi$-bondings. The materials with Lder's band have very small amount of wear at the initial state. It suggests that initial frictional shear deformation be consumed to the formation of the Lder's band. The average wear amounts of the materials increase very steeply as the øu the stress-strain ratio at the ultimate point, decreases.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.655-659
• /
• 1997

The analysis of cracks at the interface between dissimilar materilar has received a great deal of attention in recent years. In this paper we conducted the static tensile test for the aluminum bonded single lap-joint with the interface edge crack. Comparing this results, that is ultimate load and strain value of aluminum adherend by strain gauge with the fracture mechanics parameters, compliance and stress intensity factors acquied from the boundary element analysis, we concluded that there are critical value of crack length to provoke the interface fracture.

• Structural Engineering and Mechanics
• /
• 제88권3호
• /
• pp.201-208
• /
• 2023

In this work, the effect of the correction fibers direction on the efficiency of repairing damaged composite plates was highlighted. The composite plates studied in this work consist of eight layers of graphite/epoxy, while the patch used in this repair consists of four layers of the same type. The results obtained in this work, whether with regard to the experimental or analytical side, showed that the fibers orientation affects the repair efficiency, so the closer the angle of fibers inclination is to the tensile strength direction, the performance of the composite material is ideal. Hence, we conclude that the composite materials with longitudinal fibers (Parallel to tensile strength) is the most powerful and efficient material in performance.

• Advances in materials Research
• /
• 제1권3호
• /
• pp.169-182
• /
• 2012

In this paper the intrinsic influence of micron-sized nickel particle reinforcements on microstructure, micro-hardness tensile properties and tensile fracture behavior of nano-alumina particle reinforced magnesium alloy AZ31 composite is presented and discussed. The unreinforced magnesium alloy (AZ31) and the reinforced nanocomposite counterpart (AZ31/1.5 vol.% $Al_2O_3$/1.5 vol.% Ni] were manufactured by solidification processing followed by hot extrusion. The elastic modulus and yield strength of the nickel particle-reinforced magnesium alloy nano-composite was higher than both the unreinforced magnesium alloy and the unreinforced magnesium alloy nanocomposite (AZ31/1.5 vol.% $Al_2O_3$). The ultimate tensile strength of the nickel particle reinforced composite was noticeably lower than both the unreinforced nano-composite and the monolithic alloy (AZ31). The ductility, quantified by elongation-to-failure, of the reinforced nanocomposite was noticeably higher than both the unreinforced nano-composite and the monolithic alloy. Tensile fracture behavior of this novel material was essentially normal to the far-field stress axis and revealed microscopic features reminiscent of the occurrence of locally ductile failure mechanisms at the fine microscopic level.

• Safety and Health at Work
• /
• 제1권1호
• /
• pp.43-50
• /
• 2010

Objectives: The objective of this study was to investigate the effect of chain installation condition on stress distribution that could eventually cause disastrous failure from sudden deformation and geometric rupture. Methods: Fractographic method used for the failed chain indicates that over-stress was considered as the root cause of failure. 3D modeling and finite element analysis for the chain, used in a crane hook, were performed with a three-dimensional interactive application program, CATIA, commercial finite element analysis and computational fluid dynamic software, ANSYS. Results: The results showed that the state of stress was changed depending on the initial position of the chain that was installed in the hook. Especially, the magnitude of the stress was strongly affected by the bending forces, which are 2.5 times greater (under the simulation condition currently investigated) than that from the plain tensile load. Also, it was noted that the change of load state is strongly related to the failure of parts. The chain can hold an ultimate load of about 8 tons with only the tensile load acting on it. Conclusion: The conclusions of this research clearly showed that a reduction of the loss from similar incidents can be achieved when an operator properly handles the installation of the chain.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1995년도 추계학술발표회논문집(2)
• /
• pp.771-776
• /
• 1995

Tensile and J-R tests were carried out to estimate the effects of dynamic strain aging(DSA) on SA106Gr.C piping steel. Tensile tests were performed under temperature range RT to $400^{\circ}C$ md strain rates from $1.39{\times}10^{-4}\;to\;6.95{\times}10^{-2}/s$. Fracture toughness was tested in the temperature range RT to $350^{\circ}C$ and load-line displacement rates 0.4 and 4mm/min. The effects of DSA on the tensile properties were clearly observed for phenomena such serrated flow, variation of ultimate and yield stress, and negative stram rate sensitivity. However, the magnitude of serration and strength increase by DSA was relatively small. this may be due to high ratio of Mn to C. In addition, crack initiation resistance, Ji and crack growth resistance, dJ/da were reduced in the range of $200-300^{\circ}C$, where DSA appeared as serrated flow and UTS hardening. The temperature corresponding to minimum fracture resistance was shifted to higher temperature with increasing loading rate.