• Clean Technology
• /
• v.23 no.2
• /
• pp.148-157
• /
• 2017

To prepare UV-curable polyurethane-acrylate oligomer, NCO-terminated urethane prepolymers with trimethylolpropane, [TMP; 0 (0), 0.1 (0.021) and 0.2 (0.043) mole (mole fraction)] as crosslinkable tri-functional chain extender were end-capped with pentaerythritol triacrylate [PETA; 2.0 (0.400), 1.7 (0.354) and 1.4 (0.304) mole (mole fraction)] with one hydroxyl group/three vinyl functionalities. The stable as-formulated UV-curable polyurethane-acrylates [stable mixtures of PETA-capped oligomer/reactive acrylic monomer diluents without/with heptadecafluorodecyl methacrylate (PFA; 0, 6 and 9 wt%)] were formed up to 0.2 (0.043) mole (mole fraction) of TMP content in the prepolymer, while homogeneous-mixing failed at 0.3 (0.068) mole (mole fraction), in which the crosslink density in NCO-terminated urethane prepolymer was too high to enable the formation of stable mixture. This study examined the effect of TMP/PETA molar ratio and heptadecafluorodecyl methacrylate (PFA) content (wt%) on the properties of UV-cured polyurethane-acrylates as marine antifouling coating materials. The properties of UV-cured polyurethane-acrylate were found to be significantly dependent on the crosslinkable TMP/PETA ratio and PFA content. With the increasing of the TMP and PFA contents, the contact angles increased, and consequently the surface tension decreased. The adhesion of algae/barnacles to PFA contained film samples were found to be sufficiently weak to allow their easy removal. These results suggest that the UV-cured samples containing PFA have strong potential as coating materials for antifouling applications.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.1
• /
• pp.77-84
• /
• 2017

In this study, Poly-urethane acrylate (PUA) was synthesized by the reaction between Polycaprolactonetriol (PCLT) and Isophorone dissocyanate (IPDI) and hybridized with inorganic materials. Tetraethylortho silicate (TEOS) and nano clay (Closite 20A) were used as inorganic particles. For the hybridization of TEOS with PUA, sol-gel method is used, in which TEOS is made into spherical particle in the firsthand. In the case of Nano clay, hybridization is carried out through the dispersion as Nano clay has a layered structure. The solution of PUA hybrid was made into a film after UV curing and its thermo and electrical properties were measured. The experimental analysis and result demonstrate that the PUA hybrid shows an improved thermal properties and lower dielectric constant than that of the non-hybrid PUA. The trend of improved properties was different depending on structure of inorganic materials.

• Polymer(Korea)
• /
• v.34 no.6
• /
• pp.574-578
• /
• 2010

In this study, the caprolactone modified hydroxy acrylates (CHAs) were synthesized by ring-opening reaction of caprolactone and 2-hydroxyethyl acrylate (2-HEA) as initiator. Also, the caprolactone modified urethane acrylate (UA) oligomers were synthesized by condensation reaction of previously synthesized CHAs, 2-hydroxyethyl acrylate (2-HEA) and hexamethylene diisocyanate trimer (HDT). Using the hydroxy number of CHAs, the molecular weights of the CHAs were calculated easily and their molecular weight was similar to the theoretical molecular weight of them. The viscosity of UA oligomers decreased as increasing a content of CHA in the UA oligomer. Cure films were prepared from UA oligomer, reactive diluents, and UV initiator to investigate their physical properties. The thermal stability and color difference on high temperature for the cured film were improved as increasing the crosslinking density. Their surface hardness was also increased as increasing crosslinking density of the cured films, but their elongation at break was decreased.

• Journal of Adhesion and Interface
• /
• v.24 no.1
• /
• pp.26-35
• /
• 2023

Generally, solvent-type coatings generate a large amount of volatile organic chemicals(VOC), which are carcinogenic substances, in the manufacturing process, and their use is regulated due to environmental problems. There is also the problem of resource depletion due to limited fossil fuels. Therefore, in this study, UV-curable urethane acrylate oligomers were synthesized with different contents of isosorbide, which is a biomass material, and proceeded to evaluate the physical properties of coatings. As the isosorbide contents increased, the viscosity, glass transition temperature, tensile strength, stain resistance, and pencil hardness increased, but elongation and flexibility decreased, and BOI-3 showed the best adhesion. The isosorbide content of the oligomer fixed at 20%, UV-curable urethane acrylate oligomer was synthesized according to the content ratio of polycaprolactone diol(PCL) and Ecoprol H1000(Ecoprol). As the PCL/Ecoprol content ratio increased, the glass transition temperature, elongation, and flexibility increased, but the tensile strength and pencil hardness decreased. It was confirmed that the adhesion and stain resistance increased by improving the surface bonding strength of PCL. All films of oligomers synthesized were transparent without discoloration.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.256-260
• /
• 2015

The addition of montmorillonite (MMT) in the UV curable polyurethane diacrylate based resins was investigated to fabricate nanocomposites with improved mechanical properties and water sorption behavior using different photoinitiator systems. As a result, it was observed that 1 wt% of clay loading fairly improved tensile resistance and water uptake behavior. It can be also confirmed that dual photoinitiator system consisted of benzyldimethyl ketal and bisacyl phosphine oxide exhibited enhanced energy absorption band 340~450 nm even with 3 wt% of MMT concentration, which may affect the curing behavior of nanocomposite especially in our UV lamp system.

• Polymer(Korea)
• /
• v.35 no.2
• /
• pp.183-188
• /
• 2011

Pentaerytritol triacrylate (PETA) was synthesized by a condensation reaction between pentaerytritol and acrylic acid. The highest yield of PETA was obtained when heptane was used as a solvent under the 1:4 mole ratio of pentaerytritol and acrylic acid. The 6-functional urethane acrylates(UA) were also synthesized by a condensation reaction between PETA and diisocyanate. Cured films were prepared from the mixtures of UA oligomer, reactive diluents and UV initiator to investigate their physical properties. The thermal stability of the aliphatic urethane acrylate was better than that of the aromatic urethane acrylate. The UA-2 showed good hardness and scratch resistance properties while the UA-l with a high degree of curing density exhibited a better chemical resistance. All the UA oligomers showed fairly good adhesion strengths but the other physical properties of UA-3 were poor due to its low curing density.

• Journal of Adhesion and Interface
• /
• v.18 no.3
• /
• pp.127-133
• /
• 2017

In this study, to develop the adhesives with improved waterproof properties for display application, UV-curable urethane acrylate oligomers containing a fluorine moiety were synthesized from hydrogenated polybutadiene diol (HLBH-P2000), perfluoropolyether diol (HTPFPE), isophorone diisocyanate (IPDI) and 2-hydroxyethyl acrylate (HEA). The properties which were related waterproof performance such as contact angle, surface energy and water vapor transmission ratio (WVTR) of synthesized fluorine induced urethane acrylate oligomers were measured. As the HTPFPE content increased, the contact angle also increased from 97.9 degree to 104.4 degree. The surface energy and WVTR decreased as the HTPFPE content increased. The adhesion strength also decreased according to the HTPFPE content increased, and the adhesion strength reduction had greatly increased as the HTPFPE content increased. The findings of this study will be beneficial for developing waterproofing adhesives in the field of display which has recently been a waterproof issue.

• Korean Chemical Engineering Research
• /
• v.46 no.1
• /
• pp.76-81
• /
• 2008

UV curable pressure sensitive adhesive (PSA) was made by blending the di-functional or hexa-functional urethane-acrylate oligomer with synthesized acrylic PSA. The change of adhesive property and removability were investigated at various oligomer contents under each oligomer. As the content of oligomer increased, the peel strength was increased before UV irradiation, but it was decreased after UV irradiation. Also, it was observed that the peel strength increased with decrease of storage modulus (G'), and that loss factor (tan ${\delta}$) of the adhesive material affected the adhesive properties and removability.

• Applied Chemistry for Engineering
• /
• v.5 no.5
• /
• pp.857-861
• /
• 1994

UV curable hybrid systems have been investigated in the urethane acrylate based formulations where potentially irritant acrylate monomers have been substituted by vinyl ethers. Generally, among the systems studied, coating properties of hybrid system are superior to those of free radical hut inferior to those of cationic systems. When the content of acrylic oligomer is above 70%, however, hybrid system could render an excellent combination of coating and curing properties which outperforms both cationic and free radical systems. Photo-DSC has been used to follow the progress of crosslinking of various coating systems. Results imply that the critical factors in determining the curing rates of coating formulations are different depending upon the formulation characteristics. In the same type of hybrid formulations, the monomer/oligomer ratio rather than photoinitiator efficiency is the critical factor determining the curing rate of the systems.

• Journal of Adhesion and Interface
• /
• v.13 no.4
• /
• pp.156-162
• /
• 2012

Polyurethane (PU)/organoclay nanocomposites were prepared by mixing UV curable urethane acrylate oligomer with organoclay, and a subsequent curing by UV irradiation. As organoclays, commercially available Cloisite 20A (C20A) and acrylsilane modified C20A were used. XRD and TEM analyses revealed that the UV cured PU/clay nanocomposites formed intercalated nanocomposites, and acrylsilane modified C20A are dispersed more finely than unmodified C20A in PU matrix. DMTA, pencil hardness and adhesion test onto PET substrate showed that the clay nanolayers induced an increase in the properties, and the enhancement in the properties was more pronounced in the PU/acrylsilane modified C20A nanocomposites than in the PU/unmodified C20A nanocomposites. It was also observed that the PU/surface modified clay nanocomposites showed remarkably lower shrinkage upon UV curing than the unfilled PU. The nanocomposites showed excellent optical transparency but lower gloss as compared to unfilled PU.