• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.3
• /
• pp.640-658
• /
• 1996

The purpose of this study was to examine the mechanism of improving acid resistance of Nd-YAG laser irradiated tooth enamel and determine the most effective energy density for improving acid resistance. The bovine tooth enamel were lased with a pulsed Nd-YAG laser. The energy densities of exposed laser beam were varied from 10 to $70\;J/cm^2$. To investigate the degree of improving acid resistance by irradiation, all the samples were submerged to demineralize in 0.5 N $HClO_4$ solution for 1 minute. After 1 minute, 0.05 % $LaCl_3$ was added to the solution for interrupting the demineralization reaction. The amounts of dissolved calcium and phosphate in the solution were measured by using an atomic absorption spectrophotometer and the UV/VIS spectrophotometer, respectively. To examine the mechanism of improving acid resistance, X-ray diffraction analysis, infrared spectroscopy, and scanning electron microscopy were taken. The X-ray diffraction pattern of the samples were obtained in the $10^{\circ}{\sim}80^{\circ}2{\theta}$ range with $Cu-K{\alpha}$ radiation using M18HF(Mac Science Co.) with X-ray diffractometer operating at 40 KV and 300 mA. The infra-red spectra of the ground samples in 300 mg KBr pellets 10 mm diameter were obtained in the $4000cm^{-1}\;to\;400cm^{-1}$ range using JASCO 300E spectrophotometer. The scanning electron microscopy was carried out using JSM6400(JEOL Co.) with $500{\sim}2000$ times magnification. The results were as follow 1. The concentration of calcium dissolved from laser irradiated enamel with $50J/cm^2$ was significantly lesser than that of unlased control group (p<0.05) 2. From the result of the X-ray diffraction analysis, $\beta$-TCP, which increases acid solubility, was identified in lased enamel but the diffraction peaks of (002) and (004) became sharp with increasing energy density of laser irradiation. This means that the crystals in lased samples were grown through the c-axis and subsequently, the acid solubility of enamel decreased. 3. The a-axis parameter was slightly increased by laser irradiation, whereas the c-axis parameter was almost constant except for a little decrease at $50J/cm^2$. 4. In the infra-red spectra of lased enamels, phosphate bands ($600{\sim}500cm^{-1}$), B-carbonate bands (870, $1415{\sim}1455cm^{-1}$), and A-carbonate band ($1545cm^{-1}$) were observed. The amounts of phosphate bands and the B-carbonate bands were reduced, on the other hand, the amount of the A-carbonate band was increased by increase the energy density. 5. The SEM experiments reveal that the surface melting and recrystallization were appeared at $30J/cm^2$ and the cracks were observed at $70J/cm^2$. From above results, It may be suggested that the most effective energy density for improving acid resistance of tooth enamel with the irradiation of Nd-YAG laser was $50J/cm^2$. The mechanism of improving acid resistance were reduction of permeability due to surface melting and recrystallization of lased enamel and reduction of acid solubility of enamel due to decrease of carbonate content and growth of crystal.

• Journal of the Korean Vacuum Society
• /
• v.17 no.1
• /
• pp.16-22
• /
• 2008

We studied plasma etching of polycarbonate in $O_2/SF_6$, $O_2/N_2$ and $O_2/CH_4$. A capacitively coupled plasma system was employed for the research. For patterning, we used a photolithography method with UV exposure after coating a photoresist on the polycarbonate. Main variables in the experiment were the mixing ratio of $O_2$ and other gases, and RF chuck power. Especially, we used only a mechanical pump for in order to operate the system. The chamber pressure was fixed at 100 mTorr. All of surface profilometry, atomic force microscopy and scanning electron microscopy were used for characterization of the etched polycarbonate samples. According to the results, $O_2/SF_6$ plasmas gave the higher etch rate of the polycarbonate than pure $O_2$ and $SF_6$ plasmas. For example, with maintaining 100W RF chuck power and 100 mTorr chamber pressure, 20 sccm $O_2$ plasma provided about $0.4{\mu}m$/min of polycarbonate etch rate and 20 sccm $SF_6$ produced only $0.2{\mu}m$/min. However, the mixed plasma of 60 % $O_2$ and 40 % $SF_6$ gas flow rate generated about $0.56{\mu}m$ with even low -DC bias induced compared to that of $O_2$. More addition of $SF_6$ to the mixture reduced etch of polycarbonate. The surface roughness of etched polycarbonate was roughed about 3 times worse measured by atomic force microscopy. However examination with scanning electron microscopy indicated that the surface was comparable to that of photoresist. Increase of RF chuck power raised -DC bias on the chuck and etch rate of polycarbonate almost linearly. The etch selectivity of polycarbonate to photoresist was about 1:1. The meaning of these results was that the simple capacitively coupled plasma system can be used to make a microstructure on polymer with $O_2/SF_6$ plasmas. This result can be applied to plasma processing of other polymers.

• Korean Journal of Food Science and Technology
• /
• v.15 no.2
• /
• pp.170-176
• /
• 1983

Starchy single cell protein produced by a starch-utilizing yeast, Sporobolomyces holsaticus FRI Y-5 was analyzed for its composition such as intracellular protein, amino acids, fatty acids, minerals, vitamins and pigments. It was shown that it contained 33.08% of total carbohydrate, 45.63% of crude protein, 20.01% of crude lipid, 3.24% of ash and 4.46% of pigment. Whole cell extracted by cold and hot NaOH method contained 40.89% of soluble protein and the estimated nucleic acid content from crude and soluble protein contents was about 7.6%. The sulphur-containing amino acids, threonine, isoleucine and valine were analyzed to be the limiting amino acids in the starchy SCP, and the protein score was calculated as 89.4. It was shown from its fatty acid analysis that it contained $6.5%\;of\;C_{16:0}$, $2.4%\;of\;C_{18:0}$, $81.9%\;of\;C_{18:1}$, $3.2%\;of\;C_{18:2}$, and $6.0%\;of\;C_{18:3}$. Also it was observed that it contained, per 100 g of dry cell, 365.33mg of Mg and 282.75mg of K more than Fe and Ca. The content of Vit. $B_2$ was 3.7mg per 100 g of dry cell, but niacin was not detected under this experimental condition. The UV-visible scanning result of pigment extract showed that the yeast contained carotenoid and unknown pigments.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.434-434
• /
• 2012

Despite recent efforts for fabricating flexible transparent conducting films (TCFs) with low resistance and high transmittance, several obstacles to meet the requirement of flexible displays still remain. Indium tin oxide (ITO) thin films, which have been traditionally used as the TCFs, have a serious obstacle in TCFs applications. SWNTs are the most appropriate materials for conductive films for displays due to their excellent high mechanical strength and electrical conductivity. Recently, it has been demonstrated that acid treatment is an efficient method for surfactant removal. However, the treatment has been reported to destroy most SWNT. In this work, the fabrication by the spraying process of transparent SWNT films and reduction of its sheet resistance by Au-ionic doping treatment on PET substrates is researched. Arc-discharge SWNTs were dispersed in deionized water by adding sodium dodecyl sulfate (SDS) as surfactant and sonicated, followed by the centrifugation. The dispersed SWNT was spray-coated on PET substrate and dried on a hotplate. When the spray process was terminated, the TCF was immersed into deionized water to remove the surfactant and then it was dried on hotplate. The TCF film was then was doped with Au-ionic doping treatment, rinsed with deionized water and dried. The surface morphology of TCF was characterized by field emission scanning electron microscopy. The sheet resistance and optical transmission properties of the TCF were measured with a four-point probe method and a UV-visible spectrometry, respectively. This was confirmed and discussed on the XPS and UPS studies. We show that 87 ${\Omega}/{\Box}$ sheet resistances with 81% transmittance at the wavelength of 550 nm. The changes in electrical and optical conductivity of SWNT film before and after Au-ionic doping treatments were discussed. The effects of hole transport interface layer using Au-ionic doping SWNT on the performance of organic solar cells were investigated.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.97.1-97.1
• /
• 2010

유연금속기판위에 DC 마그네트론 스퍼터링을 이용하여 Ag/ZnO 이중구조의 후면반사막을 증착하고 Ag 표면조도 변화에 따른 후면반사막의 반사특성 변화와 플렉서블 비정질 실리콘 박막 태양전지의 셀 특성에 미치는 영향을 조사하였다. Substrate구조를 갖는 플렉서블 실리콘 박막 태양전지에서는 실리콘 박막 광흡수층의 상대적으로 낮은 광 흡수율로 인하여 입사광에 대한 태양전지 내에서의 광 산란 및 포획이 태양전지 효율을 증대시키는데 매우 중요한 역할을 하는 것으로 알려져 있다. 플렉서블 실리콘 박막 태양전지에서의 후면반사막은 광 흡수층에서 흡수되지 않는 입사광을 다시 반사시켜 광 흡수를 증대시키며 이때 후면반사막 표면에서 반사 빛을 효율적으로 산란시켜 이동경로를 증대시킴으로써 광 흡수율을 더욱 향상시킬 수 있다. 본 연구에서는 유연금속 기판위에 Ag와 ZnO:Al($Al_2O_3$ 2.5wt%) 타겟을 사용한 DC 마그네트론 스퍼터링법으로 Ag/AZO 이중구조의 후면반사막을 제조하고, Ag 박막의 표면형상 변화와 이에 따른 후면반사막의 반사도 변화를 비교, 분석하였다. 증착 조건 변화에 따른 표면 형상 및 반사 특성은 Atomic Force Mircroscope(AFM), Scanning electron miroscopy(SEM), UV-visible-nIR spectrometry를 통하여 분석하였다. 서로 다른 표면 거칠기를 갖는 후면반사막 위에 n-i-p구조의 a-Si:H 실리콘 박막 태양전지를 제조한 후 태양전지 동작 특성에 미치는 영향을 조사하였다. n,p층은 13.56MHz PECVD, i층은 60MHz VHF CVD를 사용하여 각각 제조 하였으며, Photo I-V, External Quantum Efficiency(EQE) 분석을 통하여 태양전지 특성을 조사 하였다. SEM 분석결과 공정 온도가 증가 할수록 Ag 박막의 표면 결정립 크기도 증가하였으며, AFM분석을 통한 Root-mean-square(Rms)값은 상온에서 $500^{\circ}C$로 증착온도가 증가함에 따라 6.62nm에서 46.64nm까지 증가하였다. Ag 박막의 표면 거칠기 증가에 따라 후면반 사막의 확산 반사도도 함께 증가하였다. 공정온도 $500^{\circ}C$에서 증착된 후면반사막을 사용하여 a-Si:H 태양전지를 제조하였을 때 상온에서 제조한 후면반사막에 비하여 단락전류밀도 (Jsc)값은 9.94mA/$cm^2$에서 13.36mA/$cm^2$로 증가하였으며, 7.6%의 가장 높은 태양전지 효율을 나타내었다.

• Journal of Microbiology and Biotechnology
• /
• v.25 no.9
• /
• pp.1433-1441
• /
• 2015

Pollution resulting from the discharge of textile dyes into water systems has become a major global concern. Because peroxidases are known for their ability to decolorize and detoxify textile dyes, the peroxidase activity of Vitreoscilla hemoglobin (VHb) has recently been studied. It is found that VHb and variants of this enzyme show great promise for enzymatic decolorization of dyes and may play a role in achieving their successful removal from industrial wastewater. The level of VHb peroxidase activity correlates with two amino acid residues present within the conserved distal pocket, at positions 53 and 54. In this work, sitedirected mutagenesis of these residues was performed and resulted in improved VHb peroxidase activity. The double mutant, Q53H/P54C, shows the highest dye decolorization and removal efficiency, with 70% removal efficiency within 5 min. UV spectral studies of Q53H/P54C reveals a more compact structure and an altered porphyrin environment (λ_Soret = 413 nm) relative to that of wild-type VHb (λ_Soret = 406), and differential scanning calorimetry data indicate that the VHb variant protein structure is more stable. In addition, circular dichroism spectroscopic studies indicate that this variant's increased protein structural stability is due to an increase in helical structure, as deduced from the melting temperature, which is higher than 90℃. Therefore, the VHb variant Q53H/P54C shows promise as an excellent peroxidase, with excellent dye decolorization activity and a more stable structure than wild-type VHb under high-temperature conditions.

• Current Research on Agriculture and Life Sciences
• /
• v.33 no.1
• /
• pp.1-5
• /
• 2015

This study investigated the chelation of a sorghum bran extract using iron (Fe) as a new natural colorant. The composition of the sorghum bran extract and chelation conditions were both examined. The thermal properties of the chelated colorants were analyzed using differential scanning calorimetry (DSC) and a thermal analyzer system(TGA). The sorghum bran extract solution showed a maximum absorbance at 281 nm based on UV/Vis spectrophotometry. According to the chelation pH conditions, pH 7.5 was the most effective. The chelation of the sorghum bran extract increased rapidly when increasing the iron concentration up to 2 mg/L, with no further chelation at a higher concentration. The particle size distribution curve for the chelated tannin revealed four groups: $4.5{\sim}17{\mu}m$, $20{\sim}42{\mu}m$, $45{\sim}80{\mu}m$, and $83{\sim}160{\mu}m$. In a DSC analysis, endothermic peaks attributed to the pyrolysis of the extract and chelated tannin were found at $318^{\circ}C$ and $415^{\circ}C$, respectively. In a TGA analysis, the chelation was shown to increase the final degradation temperature from $253^{\circ}C$ to $382^{\circ}C$, confirming that the chelation improved the thermal stability.

• Journal of Microbiology and Biotechnology
• /
• v.10 no.1
• /
• pp.27-34
• /
• 2000

The chloroform and methanol (2;1, v/v) extract from an edible plant, Actinidia arguta Planchon, appeared to possess antitumor activity against human leukemias Jurkat T and U937 cells through inducing apoptosis. The substance in the solvent extract was purified by silica gel column chromatography, preparative TLC, and Sephadex LH-20 column chromatography. Characteristics of the substance analyzed by UV scanning analysis, $^1H$ and $^{13}C$ NMR spectra suggested that the substance belongs to the chlorophyll derivatives-like group. The $IC_{50}$ value of the chlorophyll derivative (Cp-D) determined by MTT assay was $15\mu\textrm{g}/ml$ for Jurkat, $10\mu\textrm{g}/ml$ for U937, and $11.4\mu\textrm{g}/ml$ for HL-60m and was more toxic to these leukemias than to solid tumors or normal fibroblast. In order to elucidate cellular mechanisms underlying the cytotoxicity, the effect of the Cp-D on Jurkat T cells was investigated. When cells were treated with the Cp-D at a concentration of $15\mu\textrm{g}/ml$, [3H]thymidine incorporation declined rapidly and wa undetectable in 1h. However, no significant changes were made in the cell cycle distribution of the cells by 24h. The sub-Gl peak representing apoptotic cells began to be detectable in 36h, at which time apoptotic DNA fragmentation was also detected on agarose gel electrophoresis, demonstrating that the cytotoxic effect of the Cp-D is attributable to the induced apoptosis. Under the same conditions, although the protein level of cyclin-dependent kinases such as cdc4, csk6, cdk2, and cdc2 was not significantly changed until 24h, the kinase activity of all c안 rapidly declined and reached a minimum level within 1-6h and then recovered to the initial level by 12h and sustained until 24h. These results suggest that inactivation of cdks at an inappropriate time during the cell cycle progression in jurkat T cells following a treatment with the Cp-D leads to induction of apoptotic cell death.

• Korean Journal of Materials Research
• /
• v.27 no.11
• /
• pp.631-635
• /
• 2017

We report facile solution processing of mesoporous hematite (${\alpha}-Fe_2O_3$) thin films for high efficiency solar-driven water splitting. $Fe_2O_3$ thin films were prepared on fluorine doped tin oxide(FTO) conducting substrates by spin coating of a precursor solution followed by annealing at $550^{\circ}C$ for 30 min. in air ambient. Specifically, the precursor solution was prepared by dissolving non-toxic $FeCl_3$ as an Fe source in highly versatile dimethyl sulfoxide(DMSO) as a solvent. The as-deposited and annealed thin films were characterized for their morphological, structural and optical properties using field-emission scanning electron microscopy(FE-SEM), X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS) and UV-Vis absorption spectroscopy. The photoelectrochemical performance of the precursor (${\alpha}-FeOOH$) and annealed (${\alpha}-Fe_2O_3$) films were characterized and it was found that the ${\alpha}-Fe_2O_3$ film exhibited an increased photocurrent density of ${\sim}0.78mA/cm^2$ at 1.23 V vs. RHE, which is about 3.4 times higher than that of the ${\alpha}-FeOOH$ films ($0.23mA/cm^2$ at 1.23 V vs. RHE). The improved performance can be attributed to the improved crystallinity and porosity of ${\alpha}-Fe_2O_3$ thin films after annealing treatment at higher temperatures. Detailed electrical characterization was further carried out to elucidate the enhanced PEC performance of ${\alpha}-Fe_2O_3$ thin films.

• Journal of the Korean Ceramic Society
• /
• v.56 no.2
• /
• pp.178-183
• /
• 2019

A process of fabricating the foamed glass that has closed pores with 8 ~ 580 ㎛ sizes without a blowing agent by sintering 10 ㎛ boron-free glass powder composed of CaO, MgO, SO₃, Al₂O₃-83 wt% SiO₂ at a molding pressure of 0 ~ 120 MPa and a sintering temperature of 750 ~ 1000℃ was investigated. To analyze the glass transition temperature of glass powder, thermogravimetric analysis-differential thermal analysis (TGA-DTA) method were used. The microstructure and pore size of foamed glass were examined using the optical microscopy and field emission scanning electron microscopy (FE-SEM). For the thermal diffusivity and color of the fabricated samples, a heat flow meter and ultraviolet-visible-near-infrared (UV-VIS-NIR)-colormetry were used, respectively. In the TGA-DTA result, the glass transition temperature of glass powder was confirmed to be 626℃. In the microstructure result, closed pores of 7 ~ 20 ㎛ were formed at 750 ~ 900℃, and they were not affected by the molding pressure and sintering temperature. However, at 1,000℃, when there was 0 MPa molding pressure, closed pores of 580 ㎛ were confirmed, and the pore size decreased as the molding pressure increased. Moreover, at a molding pressure of 30 MPa or higher, closed pores of approximately 400 ㎛ were formed. The porosity showed an increasing trend of smaller molding pressure and larger sintering temperature, and it was controllable in the range of 5.69 ~ 68.45%. In the thermal diffusivity result, there was no change according to the molding pressure, and, by increasing the sintering temperature, up to 0.115 W/m·K could be obtained. The Lab color index (CIE-Lab) results all showed a similar translucent white color regardless of molding pressure and sintering temperature. Therefore, based on the foamed glass without boron and blowing agent, it was confirmed that white foamed glass, which has closed pores of 8 ~ 580 ㎛ and a thermal diffusivity characteristic of 0.115 W/m·K, can be fabricated by changing the molding pressure and sintering temperature.