• Applied Chemistry for Engineering
• /
• v.24 no.5
• /
• pp.499-506
• /
• 2013

As the usuage of tempered glass for touch panel increased rapidly with the development of industry, the amount of UV curable coating solution used to protect glass surfaces during a tempered glass manufacturing process increased as well. The UV curable coating has advantages compared to thermal curing such as shortened curing time and non-solvent. Appropriated polymer and monomer were used as an acid polymer to grant an alkali peeling ability. The monomers were 2-hydroxyl methylacrylate, 1,6-hexanediol diacrylate and dipentaerythritol hexaacrylate which have acryl groups of 1, 2, and 6, respectively. The combination of three different types of photoinhibitors were used and bisphenol A epoxy diacrylate was used as an oligomer. In this study, experiments were carried out by controlling the amount of photoinitiator, oligomer, and additive while maintaining the constant content of the acid polymer and the acrylic monomer. The changes in physical properties according to the additive content were investigated. It was found that the combination of photoinitiators was necessary to achieve the hardness above 4H and it was possible to control the delamination type of the coating film from a sheet to pieces by the addition of TPO as an initiator. The increase in oligomer contents increased the hardness and adhesiveness alongside dissection time. Talc content of 20 wt% showed the best results.

• Polymer(Korea)
• /
• v.28 no.4
• /
• pp.298-304
• /
• 2004

We fabricated a polymer dispersed liquid crystal (PDLC) cell using LC with negative dielectric anisotropy and UV curable monomer exhibiting transparent state initially (called normally transparent (NT)) and studied the electro-optic characteristics. The NT PDLC cell made with the ratio of LC : monomer = 70/30 wt%, curing temperature of 20 $^{\circ}C$ and strong UV intensity of 198 ㎽/$\textrm{cm}^2$ had high contrast ratio and showed good electro-optic characteristics. In this condition, LC is aligned vertically on the substrate due to the vertical alignment layer and the polymer made with the UV exposure does not influence the alignment of the LC much. Therefore, the transmittance at the zero voltage is very high and the scattering state of the cell is good after applying the voltage because LC with negative dielectric anisotropy tries to align perpendicular to the field. And also, the NT PDLC cell showed better viewing angle characteristics than that in the normally scattering (NS) PDLC.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.424-425
• /
• 2007

We have studied the optically compensated splay mode using reactive mesogen (RM) monomer to reduce setting voltage and phase transition time from initial bend to splay state. When the OCS cell has low pretilt angle close to $45^{\circ}C$, OCS state can be formed easily. The low pretilt angle was formed through the polymerization of UV curable reactive RM monomer at the surfaces. In this way, reorientation of the LC is well defined and thus the device shows better performances in setting voltage and phase transition time.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.4 s.37
• /
• pp.275-280
• /
• 2005

We propose a new approach to greatly simplify the fabrication of conventional nanoimprint lithography (NIL) by combined nanoimprint and photolithography (CNP). We introduce a hybrid mask mold (HMM) made from UV transparent material with a UV-blocking Cr metal layer placed on top of the mold protrusions. We used a negative tone photo resist (PR) with higher selectivity to substrate the CNP process instead of the UV curable monomer and thermal plastic polymer that has been commonly used in NIL. Self-assembled monolayer (SAM) on HMM plays a reliable role for pattern transfer when the HMM is separated from the transfer layer. Hydrophilic $SiO_2$ thin film was deposited on all parts of the HMM, which improved the formation of SAM. This $SiO_2$ film made a sub-10nm formation without any pattern damage. In the CNP technique with HMM, the 'residual layer' of the PR was chemically removed by the conventional developing process. Thus, it was possible to simplify the process by eliminating the dry etching process, which was essential in the conventional NIL method.

• Journal of Adhesion and Interface
• /
• v.11 no.2
• /
• pp.50-56
• /
• 2010

Polyethyleneterephthalate (PET) film is widely used in various industrial fields such as mobile phone, display pannel, notebook etc. Recently PET film attached on indium tin oxide (ITO) surface has a role of high pencil hardness, high refractive index etc. So we synthesized two types of multi-functional monomer which are epoxy modifed acrylate and unmodified acrylate type using recyclable resource like phloroglucinol, derived from trinitrotoluene. We studied the effect of multi-functional monomer's chemical structure on the various properties such as refractive index, optical transmittance, and pencil hardness. We characterized synthesized multi-functional monomer by qualitative analysis through H NMR. We observed that pencil hardness of 1,3,5-triepoxide benzene and 1,3,5-triacrylate benzene they have the range of 2~3 H at high UV dosage of 300 mW. Refractive index appeared the value of 1.54~1.57. Transmittance of all multi-functional monomers has more than 93%.

• Journal of Adhesion and Interface
• /
• v.15 no.1
• /
• pp.22-30
• /
• 2014

Self-photoinitiating acrylate (SPIA) which can undergo self-initiation under UV irradiation was synthesized by a Michael addition in the presence of a base catalyst. The SPIA polymerizations were investigated by photo-differential scanning calorimeter (photo-DSC) and surface physical properties such as pendulum hardness and pencil hardness. The results showed that the SPIA can cure upon UV irradiation by itself without a photoinitiator. But we found out that both the curing rate and the conversion were too low for the self-curing reaction of SPIA. In order to improve the SPIA curing properties, we introduced the SPIA/cationic hybrid system and observed the effects of the addition of commercial free radical type monomer and photoinitiator on the curing behaviors. SPIA/cationic hybrid system was the best suitable to improve the SPIA curing properties. The kinetic analysis indicated that the cationic monomer and photoinitiator apparently accelerated the cure reaction and rate of the hybrid SPIA system, mostly due to the synergistic effect of cationic monomer and photoinitiator increasing the mobility of active species and the generation of reactive species (free radical, cation) during the photopolymerization process. The physical properties showed that, unlike typical free radical system, the hybrid systems did not show oxygen inhibition effect because of cationic reaction on the coating surface.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.281-286
• /
• 2015

UV-cured acrylic copolymer pressure sensitive adhesive (PSA) having different amounts of crosslinking agents were prepared and adhesion properties were investigated. 0.01 wt% of MMT clay was dispersed in 2-ethylhexyl acrylate (2-EHA)/acrylic acid (AA) monomer mixture containing 0, 0.05, 0.1 and 0.3 wt% 1,6-hexandiol diacrylate (HDDA) for crosslinking. It was investigated that the curing behavior and surface chemistry of PSAs were merely affected by the presence of MMT clays. On the other hand, adhesive properties were influenced by the MMT addition; a cohesive failure was restrained due to improved molecular elasticity even in uncrosslinked acrylic PSAs. However, it was also appeared that combination of 0.3 wt% crosslinking agent and MMT loading might result in the damage of adhesion properties of PSAs possibly due to the lack of chain flexibility. In our studies, it is suggested that the 2-EHA/AA PSAs incorporating 0.01 wt% of MMT and crosslinked with 0.05 wt% of HDDA exhibited the balanced adhesion properties without severe cohesive failure during strip.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.316-320
• /
• 2009

UV curable hard and color coatings were formed on polycarbonate(PC) films. The coating materials were composed of a commercially available end-capped polyester(EB830), diacrylate monomer(HDDA), silicon acrylate, photoinitiator, and organic dye as a coloring agent. The surface properties of coating films were evaluated, and the influences of the compositions of coating materials were investigated. The coating films showed high transmission and good adhesion between coating layer and PC substrate. And the coating films exhibited higher hardness than bare PC film. The coating films with various colors were obtained by wet process, and the clear and color window lenses for mobile phone were prepared successfully.

• Korean Journal of Materials Research
• /
• v.30 no.11
• /
• pp.627-635
• /
• 2020

3D printing technology is a processing technology in which 3D structures are formed by fabricating multiple 2D layers of materials based on 3D designed digital data and stacking them layer by layer. Although layers are stacked using inkjet printing to release various materials, it is still rare for research to successfully form a product as an additive manufacture of multi-materials. In this study, dispersion conditions are optimized by adding a dispersant to an acrylic monomer suitable for inkjet printing using Co₃O₄ and Al₂O₃. 3D structures having continuous composition composed of a different ceramic material are manufactured by printing using two UV curable ceramic inks whose optimization is advanced. After the heat treatment, the produced structure is checked for the formation and color of the desired crystals by comparing the crystalline analysis according to the characteristics of each part of the structure with ceramic pigments made by solid phase synthesis method.

• Textile Coloration and Finishing
• /
• v.34 no.1
• /
• pp.1-9
• /
• 2022

The durable FR treatments such Pyrovatex and Proban have been used for cotton fibers, while the finishes involve toxic ammonia or formaldehyde release during finishing process or finished products. In this study, ecofriendly flame-retardant treatment of cotton fabrics was carried out using UV-curable formulations of Vinyl bisphosphonic acid (VBPA), Acrylaminide and Triacryloylhexahydro-1,3,5-triazine, as a monomer, a comonomer and a cross-linking agent respectively, which can introduce a cross-linked copolymer networks. With an optimal finish formulation, the flame retardancy of LOI 29.8 was maintained even after 10 laundering cycles. In TGA analysis, the DTGA peak decreased from 389℃ to 252℃ and the amount of char yield increased from 6.1% to 46.1% compared to the untreated cotton. In addition, MCC analysis showed that Peak HR and THR decreased by 59.4% and 69.2% respectively, compared to the untreated cotton. The pyrolysis and combustion behaviors of the FR-treated cotton implied a condensed-phase flame-retarding mechanism.