• Journal of the Korean Graphic Arts Communication Society
• /
• v.13 no.2
• /
• pp.47-53
• /
• 1995

Photosensitive resin of azide type is good for resolution and inner solvent, but it is really problem to development of practical use because fanctional groups of polymer has many hydrophilic radicals. By careful attention to this point, this study was investigated synthesis term, photo property and development property of composed photosensitive resin of azida type, it is to this effect. 1) H-NMR spectrum of compared DABCI showed amion redical by $\delta$6.0~6.1ppm to substitude for azide radical by amino radical by $\delta$8.9~9.45ppm, and FT-IR absorption spectra showed the absorption bends at 2100cm. 2)FT-IR absorption spectra of PHS1-DAB, PHS2-DAB, CMM-DAB and CHM-DAB showed azida radical pick to be lost at after irradiation by UV light. 3) According to exposuer change of PHS1-DAB, PHS2-DAB, CMM-DAB and CHM-DAB, absorption maximum value of UV spectrum change was 280nm. 4) to compared relative sensitivity of compared photosensitive resin, PHS2-DAB was the best and to compared insolubility rate of compared photosensitive resin, CMM-DAB was the lower. 5)Solubility if NaOH was the best by 1.0mol/$\ell$ and solubility of developing solution of ethanol to water was it in the ratio of 4 to 1.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.6
• /
• pp.176-183
• /
• 2002

Plasma Display Panel(PDP) is a type of flat panel display utilizing the light emission produced by gas discharge. Barrier Ribs of PDP separating each sub-pixel prevents optical and electrical crosstalks from adjacent sub-pixels. The mold for forming the barrier ribs has been newly researched to overcome the disadvantages of conventional manufacturing processes such as screen printing, sand-blasting and photosensitive glass methods. The mold for PDP barrier ribs have stripes of micro grooves transferring glass-material wall. In this paper , Stripes of grooves of which width 48$\mu$m, depth 124$\mu$m , pitch 274$\mu$m was acquired by machining of single crystal silicon with dicing saw blade. Maximum roughness of the bottom of the grooves was 59.6 nm Ra in grooving Si. Barrier ribs were farmed with silicone rubber mold, which is transferred from grooved Si forming hard mold. Silicone rubber mold has the elasticity, which enable to accommodate the waviness of lower glass plate of PDP. The methods assisted by the microwave and UV was adopted for reducing the forming time of glass paste.

• Tribology and Lubricants
• /
• v.36 no.5
• /
• pp.267-273
• /
• 2020

This study experimentally investigates hydrophobic surfaces fabricated via additive manufacturing. Additive manufacturing, commonly known as 3D printing, is the process of joining materials to fabricate parts from 3D model data, usually in a layer-upon-layer manner. Digital light processing is used to fabricate hydrophobic surfaces in this study. This method uses photo-curable resins and ultraviolet (UV) sources. Moreover, this technique generally has faster shaping speeds and is advantageous for the fabrication of small components because it enables the fabrication of one layer at a time. Two photo-curable resins with different compositions are used to fabricate micro-patterns of hydrophobic surfaces. The resins are composed of a photo-initiator, monomer, and oligomer. Experiments are conducted to determine suitable process conditions for the fabrication of hydrophobic surfaces depending on the type of resin. The most important factors affecting the process conditions are the UV exposure time and slice thickness. The fabrication capability according to the process conditions is evaluated using the side and top views of the micro-patterns observed using a microscope. The micro-patterns are collapsed and intertwined when the exposure time is short because sufficient light (heat) is not applied to cure the photo-curable resin with a given slice thickness. On the other hand, the micro-patterns are attached to each other when the exposure time is prolonged because the over-curing time can cure the periphery of a given shape. When the slice is thicker, the additional curing area is enlarged in each slice owing to the straightness of UV light, and the slice surface becomes rough.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.179-179
• /
• 2006

산업기술의 고도화에 따른 IT 산업의 급속한 발전으로 각종 전자, 정보통신기기에 대해 더욱 소형화 고성능화를 요구하고 있다. 이와 같은 경향에 따라 더욱 향상된 기능을 가지고 각종 소자 부품의 개발과 동시에 유독 물질 발생이 없는 청정생산기술 개발에 대한 요구가 끊임없이 제기 되어 왔다. 이러한 요구에 부응하여 기술들이 개발되고 있으며 그 중의 하나로 잉크젯 프린팅 기술이 연구되고 있다. 특히 Dod(Drop on Demand) 방식의 잉크젯은 가정용 프린터로 개발되어 널리 보급된 기술이지만, 이 기술을 PCB 제조기술에 전용하면 친환경 생산공정으로 부품 성장밀도를 증대 시킬 수 있다. 기존의 PCB 제조기술은 전극과 신호 패턴을 형성시키기 위하여 노광공정과 에칭공정을 반복적으로 사용하고 있는데, 노광공정에서 쓰이는 마스크와 유틸리티 설비 유지 비용의 문제가 대두되고 있다. 노즐로부터 분사된 잉크 액적들의 집합으로 기판위에 점/선/면의 인쇄이미지를 구현하게 된다. 그러므로 인쇄 해상도는 잉크액적 및 인쇄 방법, 기판과의 상호작용에 크게 의존하게 된다. 잉크 액적과 기판의 상호작용에 영향을 미치는 요소로는 잉크의 물리화학적 물성(밀도, 점도, 표면장력), 잉크 액적의 충돌 조건(액적 지름, 부피, 속도), 그리고 기판의 특성(친수/소수성, Porous/Nonporous, 표면조도 등)을 들 수 있겠다. 우선적으로 노즐을 통과해서 분사되는 액적의 크기에 따라 기판위에 형성되는 라인의 두께 및 폭이 결정된다. 떨어진 액적이 기판위에서 퍼지는 것을 UV 조사를 통한 가경화 과정을 통해서 최종적으로 라인의 투께 및 폭을 조절하려고 한다. 따라서 선폭 $75{\mu}m$의 일정한 미세 배선을 형성시키기 위해 액적 크기 조절과 탄착 resist 액적 표면의 UV 가경화 조건으로 구현하려고 한다. 또한 DPI(Dot Per Inch) 조절을 통한 인쇄로 탄착 resist의 두께 확보 후 에칭시 박리되는 현상을 억제 시키려 한다.

• Macromolecular Research
• /
• v.17 no.4
• /
• pp.232-239
• /
• 2009

This paper describes the simple nanopatterning of proteins on polyelectrolyte surfaces using microcontact printing with a nanopatternable, hydrophilic composite nanomold. The composite nanomold was easily fabricated by blending two UV-curable materials composed of Norland Optical Adhesives(NOA) 63 and poly(ethylene glycol) dimethacrylate(PEG-DMA). NOA 63 provided stable nanostructure formation and PEG-DMA induced high wettability of proteins in the nanomold. Using the composite mold and functionalized surface with polyelectrolytes, the fluorescent, isothiocyanate-tagged, bovine serum albumin(FITC-BSA) was successfully patterned with 8 nm height and 500 nm width. To confirm the feasibility of the protein assay on a nanoscale, a glycoprotein-lectin assay was successfully demonstrated as a model system. As expected, the lectins correctly recognized the nano-patterned glycoproteins such as chicken ovalbumin. The simple preparation of composite nanomold and functionalized surface with a universal platform can be applied to various biomolecules such as DNA, proteins, carbohydrates, and other biomolecules on a nanoscale.

• Proceedings of the Korean Printing Society Conference
• /
• 2001.06a
• /
• pp.91-91
• /
• 2001

환경문제에 대해 오래 전부터 관심을 가져온 선진국은 잉크의 수성화에 주력하여 왔으며, 그 결과 이미 수용성 소재의 양산체재에 들어가 수성 원료 사업을 대형화하는 추세에 있다. 이에 한화석유화학 중앙연구소에선 스티렌/아크릴계 수용성 High Solid 수지를 개발하여, 수성 잉크용 분산제, Resin Fortified Emulsion (RFE), UV Resist 잉크, 수성코팅제, 바닥광택제 등에 적요하기 위한 응용기술을 개발하였다. 본 연구는 수성 잉크의 주요 구성 성분인 grinding vehicle. let-down vehicle로 사용되는 수용성 High Solid 수지 (SAA 수지) 및 이를 이용한 에멀젼 수지의 합성과 수성 잉크로의 응용에 대한 것이다. SAA(HCC Soluryl Resin) 수지는 구조적으로 Styrene, Alpha-methyl Styrene, crylic Acid의 삼원공중합체이며 약 70%의 소수성 물질과 30%의 친수성 물질이 Random 하게 중합되어 있으며 약 5000∼15000정도의 낮은 분자량을 가진 물질로, 고고형분에서도 낮은 점도를 유지하기 위하여 분자량과 좁은 분자량과 좁은 분자량을 가지는 수지를 연속벌크중합방법으로 합성하였다. 또한 이를 고분자 유화제로서 사용하여 수지보강 에멀젼수지 (RFE 수지, HCC Soluryl Emulsion) 를 제조하는데 사용하였으며, SAA수지 및 RFE수지를 수성잉크용 분산제, 잉크 바인더용으로 적용하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.5
• /
• pp.456-461
• /
• 2007

In this study, a surface treatment method using accelerated Ar ions was experimented for exposing the carbon nanotubes (CNT) from the screen-printed CNT paste. After making a cathode electrode on the glass substrate, photo sensitive CNT paste was screen-printed, and then back-side was exposed by UV light. Then, the exposed CNT paste was selectively remained by development. After post-baking, the remained CNT paste was bombarded by accelerated Ar ions for removing some binders and exposing only CNTs. As results, the field emission characteristics were strongly depended on the accelerating energy, bombardment time, and the power of RF plasma ion source. When Ar ions accelerated with 100 eV energy from the 100 W RF plasma source are bombarded on the CNT paste surface for 10 min, the emission level and the uniformity were best.

• Proceedings of the Korean Printing Society Conference
• /
• 1998.10a
• /
• pp.16-21
• /
• 1998

Spectral reflrectance of the object should be mesured to predict the color of object under various illuminants. The spectral reflectance can be represented in a multidemensional space; Generally we can obtain only three-channel data from input device such as CCD camera, color scanner etc. The estimation from three dimernsional to multidimension can be achieved using principal components of spectral reflectance. In this paper, A method to predict the spectral reflectance of skin color taken by 3-channel input device is discribed. To confirm this method, we simulate color represent under various illuminants about yellow, white and colored women face.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1122-1124
• /
• 2009

Organic thin-film transistors (OTFTs) were fabricated by using the transfer patterning method. In order to remove Au pattern easily, UV-curable polymer mold was surface treated. Au source/drain (S/D) pattern was transferred to insulator-coated substrate surface. Fabricated OTFTs were compared to OTFTs using vacuum-deposited Au S/D. Additionally, transistor diodes were characterized.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.352-355
• /
• 2007

We have developed tight bonding of plastic LCD with new rigid spacer. For tight bonding of two plastic substrates, we designed structures to collect UV or thermal epoxy placed on the top of rigid spacer spontaneously by capillary effect. We confirmed that tight bonded plastic LCD has a good adhesion without induced defects and a high mechanical stability against the various external deformations. This method can be applicable to the fabrication of large plastic LCDs using stamping process.