• Bulletin of the Korean Chemical Society
• /
• v.32 no.9
• /
• pp.3251-3254
• /
• 2011

To probe the chemical constituents of Patrinia scabra, we undertook the phytochemical investigation on its roots, which led to the isolation and elucidation of three new iridoid glucosides, scabroside A-C (1-3), along with three known iridoids, jatamanin J (4), isopatriscabroside I (5) and loganic acid (6) from the aqueous fraction of the ethanolic extract of the roots. The structures and relative configurations of the three new compounds were elucidated by spectroscopic methods including IR, UV, MS, 1D and 2D NMR experiments. Compound 3 was an unusual iridoid with an oxygen bridge connecting C-3 and C-8.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.350-350
• /
• 2011

ZnO는 II-VI족 화합물 반도체로서 3.37 ev의 band gap energy와 60 mv의 exciton binding energy를 가지며 차세대 소자로 다양한 분야에서 연구되어지고 있다. ZnO 박막과는 다르게 ZnO nano structure는 효율성과 특성 향상의 이점으로 태양전지와 투명전극 소자에 많은 연구가 되고 있으며 UV 레이저, 가스센서, LED, 압전소자, Field Emitting Transistor (FET) 등 다양한 응용분야에서 연구되고 있다. 본 연구에서는 유리 기판 위에 RF Magnetron sputtering법을 이용해 ZnO buffer layer를 다양한 두께(~1,000${\AA}$)로 증착한 뒤, Zn powder (99.99%)를 지름 2inch 석영관 안에 넣어 Thermal furnace장비를 이용하여 Thermal Evaporation법으로 약 500$^{\circ}C$에서 30분 동안 촉매 없이 성장 하였다. 수직성장된 ZnO 나노 구조체의 특성을 전계방출주사전자현미경(SEM), X-선 회절패턴(XRD), UV-spectra를 이용하여 분석하였다. SEM 분석을 통하여 ZnO buffer layer위에 성장된 ZnO 나노 구조체는 직경이 약 ~50 nm, 길이가 ~2 um까지 성장을 보였으며, XRD 측정결과, ZnO 우선 성장 방향(002)을 확인하였다. 두 가지 측정을 통하여 ZnO buffer layer의 유무에 따라 성장 특성이 향상되었음을 확인하였으며, 이는 buffer layer가 seed 역할을 한 것으로 사료된다. UV-spectra 측정을 통하여 가시광 영역(400~780 nm)에서 60%대의 투과도를 보여 가시광 영역에서 투명성을 요구하는 전자 소자 및 광소자 등에 적용 가능성을 확인하였다. 이 연구를 통하여 우수한 투과도를 가지며 유리 기판위에 수직성장된 ZnO 나노구조체는 태양전지와 플렉서블 디스플레이 등 다양한 활용 분야를 제시할 수 있다.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.17 no.1
• /
• pp.126-130
• /
• 2004

Objectives; Bioassay-directed fractionation of the dried roots of Salvia miltiorrhiza led to the isolation of abietane tanshinones, crptotanshinone and dihydrotanshinone. Methods: Their structures were elucidated using 1H-and 13C-NMR, UV, IR and mass spectral analysis. Result and Conclusions : These compounds exhibited a moderate antimicrobial activities against Staphylococcus epidemidis, Staphylococcus aureus, Staphylococcus pyogene. Actinobacillus actinomycetemcomitans, Escherichia coil, Enterbacter cloacae, Pseudomonas aeruginosa, Citrobacter freundii, and Samonella typhimurium.

• Journal of Society of Preventive Korean Medicine
• /
• v.9 no.1
• /
• pp.135-141
• /
• 2005

Bioassay-directed fractionation of the dired roots of Sophorae Radix led to the isolation of Sophoraflavanone G. Their structures were elucidated using 1H-NMR, 13C-NMR, UV, IR and mass spectral ananlyses. These compounds exhibited a moderate antimicrobial activities against Streptococcus gordonii, Actinobacillus actinomycetemoomitans and Porphylomonas gingivalis.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.8
• /
• pp.651-654
• /
• 2010

This paper describes the thermal and mechanical properties of doped thin film 3C-SiC and porous 3C-SiC. In this work, the in-situ doped thin film 3C-SiC was deposited by using atmospheric pressure chemical vapor deposition (APCVD) method at $120^{\circ}C$ using single-precursor hexamethyildisilane: $Si_2(CH_3)_6$ (HMDS) as Si and C precursors. 0~40 sccm $N_2$ gas was used as doping source. After growing of doped thin film 3C-SiC, porous structure was achieved by anodization process with 380 nm UV-LED. Anodization time and current density were fixed at 60 sec and 7.1 mA/$cm^2$, respectively. The thermal and mechanical properties of the $N_2$ doped porous 3C-SiC was measured by temperature coefficient of resistance (TCR) and nano-indentation, respectively. In the case of 0 sccm, the variations of TCR of thin film and porous 3C-SiC are similar, but TCR conversely changed with increase of $N_2$ flow rate. Maximum young's modulus and hardness of porous 3C-SiC films were measured to be 276 GPa and 32 Gpa at 0 sccm $N_2$, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.4
• /
• pp.237-240
• /
• 2016

The improvement of irradiation intensity and irradiation uniformity is essential for large area and high power UVA light source application. In this study, large number of chips bonded by micro soldering technique were driven by low current, and current limiting diodes were configured to supply constant current to parallel circuits consisting of large number of series strings. The dimension of light source module circuit board was $350{\times}90mm^2$ and 16,650 numbers of 385 nm flip chip LEDs were used with a configuration of 90 parallel and 185 series strings. The space between LEDs in parallel and series strings were maintained at 1.9 mm and 1.0 mm distance, respectively. The size of the flip chip was $750{\times}750{\mu}m^2$ were used with contact pads of $260{\times}669{\mu}m^2$ size, and SAC (96.5 Sn/3.0 Ag/0.5 Cu) solder was used for flip chip bonding. The fabricated light source module with 7.5 m A supply current showed temperature rise of $66^{\circ}C$, whereas irradiation was measured to be $300mW/cm^2$. Inaddition, 0.23% variation of the constant current in each series string was demonstrated.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.29.1-29.1
• /
• 2009

Fabrication of good quality P-type GaN remained as a challenge for many years which hindered the III-V nitrides from yielding visible light emitting devices. Firstly Amano et al succeeded in obtaining P-type GaN films using Mg doping and post Low Energy Electron Beam Irradiation (LEEBI) treatment. However only few region of the P-GaN was activated by LEEBI treatment. Later Nakamura et al succeeded in producing good quality P-GaN by thermal annealing method in which the as deposited P-GaN samples were annealed in N2 ambient at temperatures above $600^{\circ}C$. The carrier concentration of N type and P-type GaN differs by one order which have a major effect in AlGaN based deep UV-LED fabrication. So increasing the P-type GaN concentration becomes necessary. In this study we have proposed a novel method of activating P-type GaN by electrochemical potentiostatic method. Hydrogen bond in the Mg-H complexes of the P-type GaN is removed by electrochemical reaction using KOH solution as an electrolyte solution. Full structure LED sample grown by MOCVD serves as anode and platinum electrode serves as cathode. Experiments are performed by varying KOH concentration, process time and applied voltage. Secondary Ion Mass Spectroscopy (SIMS) analysis is performed to determine the hydrogen concentration in the P-GaN sample activated by annealing and electrochemical method. Results suggest that the hydrogen concentration is lesser in P-GaN sample activated by electrochemical method than conventional annealing method. The output power of the LED is also enhanced for full structure samples with electrochemical activated P-GaN. Thus we propose an efficient method for P-GaN activation by electrochemical reaction. 30% improvement in light output is obtained by electrochemical activation method.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.2
• /
• pp.57-62
• /
• 2018

In this study, we investigated the impurity effect of $Ga_2O_3$ doped thin film by simple doping method using Mg acetate solution. Both undoped $Ga_2O_3$ thin films and Mg-doped $Ga_2O_3$ thin films were grown on Si substrates at 600 and $900^{\circ}C$ for 30 minutes by means of a customized MOCVD method. As a result of the surface analysis, there were no obvious morphological differences by Mg impurity implantation. The surface of the thin film grown at $900^{\circ}C$ was rougher than those grown at $600^{\circ}C$ and polycrystallization was achieved. As a result of the optical property analysis, in the case of the doped sample, the overall emission peak was red shifted and the UV radiation intensity was increased. As a result of the I-V curve, the leakage current of the $600^{\circ}C$ growth thin film decreased by the Mg impurity and the photocurrent of the growth thin film of $900^{\circ}C$ increased.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.6
• /
• pp.279-282
• /
• 2013

Recently, it has been interested much that AlN (Aluminum Nitride) crystals can be applied to UV LEDs and high power devices as like GaN and SiC crystals. The reports about commercial grade of AlN wafers in the world have been absent, however several results for growth of large size of AlN single crystals have been reported from abroad. In this report, the result of AlN single crystals of a diameter of about 8 mm grown are reported. Optical microscopic characterization was applied to observe the form of the crystals and the crystal quality was evaluated by FWHM measurement by DCXRD rocking curve analysis.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.114-114
• /
• 2000

III-nitride 게 물질들은 blue와 UV 영역의 LED, LD와 같은 광소자뿐만 아니라 HBT, FET와 같은 전자소자로도 널리 응용되고 있다. 이와 같은 물질을 이용한 소자를 제작할 경우 낮은 저항의 ohmic contact은 필수적이다. p-GaN의 ohmic contact은 아직까지 많은 문제점을 내포하고 있다. 그 중의 하나는 높은 doping 농도(>1018cm-3)의 p-GaN 박막을 성장하기가 어렵다는 것이며, 또 하나는 낮은 접촉 비저항을 얻기 위해선 7.5eV 이상의 큰 재가 function을 지닌 금속을 선택해야 한다. 그러나 5.5eV 이상의 재가 function을 갖는 금속은 존재하지 않는다. 위와 같은 문제점들은 p-GaN의 접촉 비저항이 10-2$\Omega$cm2이상의 높은 값을 갖게 만들고 있으며 이에 대한 해결방안으로는 고온의 열처리를 통하여 p-GaN와 금속사이에서 화학적 반응을 일으킴으로써 표면근처에서 캐리어농도를 증가시키고, 캐리어 수송의 형태가 tunneling 형태로 일어날 수 있도록 하는 tunneling current mechaism을 이용하는 것이다. 이에 본 연구에서는 MOCVD로 성장된 p-GaN 박막을 Mg의 activation을 증가시키기 위해 N2 분위기에서 4분간 80$0^{\circ}C$에서 RTA로 annealing을 하였으며, ohmic 접촉을 위한 금속으로 높은 재가 function과 좋은 adhesion 그리고 낮은 자체저항을 가지고 있는 Ni/ZSi/Ni/Au를 ohmic metal로 하여 contact한 후에 $700^{\circ}C$에서 1분간 rapid thermal annealing (RTA) 처리를 했다. contact resistance를 계산하기 위해 circular-TLM method를 이용하여 I-V 특성을 조사하였고, interface interaction을 알아보기 위해 SEM과 EDX, 그리고 XRD로 분석하였다. 또한 추가적으로 Si 계열의 compound metal인 PdSi와 PtSi에 대한 I-V 특성도 조사하여 비교하여 보았다.