전자선 직접묘사 (E-beam direct writing lithography) 방법을 이용하여 $0.2\mum$ 과 $0.3\mum$ 의 게이트길이를 가지는 NMOS 트랜지스터를 제작하였다. 게이트만 전자선 직접묘사 방법으로 정의하고 나머지는 optical stepper를 이용하는 Mix & Match 방식을 사용하였다. 게이트산화막의 두께는 최소 6nm까지 성장시켰으며, 트랜지스터구조로서는 lightly-doped drain(LDD) 구조를 채택하였다. 짧은 채널효과 및 punch through를 줄이기 위한 방안으로 채널에 깊이 붕소이온을 주입하는 방법과 well을 고농도로 도핑하는 방법 및 소스와 드레인에 $p^-$halo를 이온주입하는 enhanced lightly-doped drain(ELDD) 방법을 적용하였으며, 제작후 성능을 각각 비교하였다.
제작된 $0.2\mum$의 게이트길이를 가지는 소자에서는 문턱전압과 subthreshold기울기는 각각 0.69V 및 88mV/dec. 이었으며, Vds=3.3V에서 측정한 포화 transconductance와 포화 드레인전류는 각각 200mS/mm, 0.6mA/$\mum$이었다. $0.3\mum$소자에서는 문턱전압과 subthreshold 기울기는 각각 0.72V 및 82mV/dec. 이었으며, Vds=3.3V에서 측정한 포화 transconductance는 184mS/mm이었다. 이러한 결과는 전원전압이 3.3V일 때 실제 ULSI에 적용가능함을 알 수 있다.
PZT thin film deposited by rf magnetron sputtering was annealed by rapid thermal process(RTP) in PbO ambient to prevent vaporing of Pb and interface reactions. Si and TiN/Ti/Si substrates were prepared to survey application of TiN/Ti layer which can prevent interface interaction with Si and crack of PZT thin films. As temperature increased. PZT thin films surface on Si substrate appeared more severe cracks which should affect electrical properties deadly. TiN/Ti(40-150${\mu}{\Omega}{\cdot}cm$) layer applied for buffer layer suppressed interface interaction and film cracking. The measured leakage current(LC) and breakdown voltage(BV) of PZT thin film on TiN/Ti/Si substrate annealed at 650$^{\circ}$C for 15 sec (thickness of 2500$\AA$) were 38 nA/cm2 and 3.5 MV/cm and dielectric constant was 310 at 1 MHz, and remanent polarization (Pr) and coercive field (Ec) were 6.4${\mu}C/cm^{2}$ and 0.2MV/cm at 60 Hz, respectively.
반도체와 관련한 실리콘웨이퍼의 평탄도는 양질의 웨이퍼를 보증하는 가장 중요한 요소이다. 따라서 평탄도(flatness)를 측정하고 제어하는 Polishing이라는 공정은 웨이퍼 생산의 여러 라인중 특별히 중요시 되는 과정이며 현재 이 공정에서는 담당 엔지니어가 웨이퍼의 모형을 모니터에서 육안으로 관찰하여 판단하고 평탄도를 높이기 위한 제어를 하고 있다. 그러나 사람에 의한 것이므로 많은 경험이 필요하고 일일이 체크해야하는 번거로움이 있다. 본 연구는 이러한 비효율적인 작업의 효율화를 위해 이루어 졌으며 Polishing 공정에 있어 평탄도를 사람이 아닌 시스템에 의해 자동으로 측정하여 제어하는 알고리즘을 제안한다. 여기서 제안한 시스템은 보간 다항식을 이용하여 웨이퍼 전역의 두께를 추정하고 Polishing공정에서 평탄도를 높이기 위해 제어 가능한 모형별로 분류할 수 있도록 하였다.
Chemical mechanical polishing (CMP) process has been widely used to planarize dielectric layers, which can be applied to the integrated circuits for sub-micron technology. Despite the increased use of CMP process, it is difficult to accomplish the global planarization of in the defect-free inter-level dielectrics (ILD). In this paper, we have investigated slurry properties and CMP performance of silicon dioxide (oxide) as a function of different temperature of slurry. Thermal effects on the silica slurry properties such as pH, particle size, conductivity and zeta potential were studied. Moreover, the relationship between the removal rate (RR) with WIWNU and slurry properties caused by changes of temperature were investigated. Therefore, the understanding of these temperature effects provides a foundation to optimize an oxide CMP Process for ULSI multi-level interconnection technology.
To achieve the ULSI goals of higher density, greater performance and operation speed have been scaled down. However, the reduction of channel length cause undesirable problems such as drop of punchthrough voltage, hot-carrier degradation and high leakage current, etc.. It is shown that the device characteristics depend on process parameters. In this Paper, we catched hold of trends of hot-carrier effects and punchthrough voltages due to variation of some process parameters such as LDD doses(P), spacer lengths, channel doses($BF_2$) and $V_T$ adjusting channel implantation energies using design trend curve (DTC). As the LDD and channel doses increased, hot-carrier phenomena became more severe, and punchthrough voltage was decreased. It were represented that punchthrough and hot carrier effects were critically depend on LDD and channel doses.
We have studied the effects of La concentration on the optical and electrical properties of lead lanthanum titanate (PLT) thin films by using sol-gel method. Both the optical and electrical properties are greatly affected by the La concentration. The refreactiv eindices of the films varied from 2.23 to 1.93 with varying La concentration in the range from 15 to 33 mol%. The dielectric constants of the films vary form 340 to 870 with varying La concentration in the range form 15 to 33 mol%. Hysteresis loop becomes slimmer with the increase of La concentration form 15 to 28mol% and little fatter again with the increase of La concentration form 28 to 33 mol%. Among the films investigated in this research, PLT(28) thin film shows the best dielectric properties for the application to the dielectrics of ULSI DRAM's. At the frequency of 100Hz, the dielectric constant and the loss tangent of PLT(28) thin films are 940 and 0.08 respectively. Its leakage current density at 1.5${\times}10^{5}$V/cm is 1${\times}10^{-6}A/cm^{2}$. The comparision between the simulated and the experimental curves for the switching transient characteristics shows that PLT (28) thin films behaves like normal dielectrics.
Chemical Mechanical Planarization(CMP) has been accepted as the most effective processes for ultra large scale integrated (ULSI) chip manufacturing. However, as the polishing process continues, pad pores get to be glazed by polishing residues, which hinder the supply of new slurry. And pad surface is ununiformly deformed as real contact distance. These defects make material removal rate(MRR) decrease with a number of polishied wafer. Also the desired within-chip planarity, within wafer non-uniformity(WIWNU) and wafer to wafer non-uniformity(WTWNU) arc unable to be achieved. So, pad conditioning in CMP Process is essential to overcome these defects. The eletroplated or brazed diamond conditioner is used as the conventional conditioning. And. allumina long fiber, the jet power of high pressure deionized water, vacuum compression. ultrasonic conditioner aided by cavitation effect and ceramic plate conditioner are once used or under investigation. But. these methods arc not sufficient for ununiformly deformed pad surface and the limits of conditioning effect. So this paper focuses on the characteristics of diamond conditioner which reopens glazed pores and removes ununiformly deformed pad away.
To improve the leakage current, we developed two step sputtering method where PZT thin film in first deposited at room temperature followed by 600.deg. C deposition. The method used an amorphous PZT layer deposited at room temperature to keep a stable interface during sputtering at high temperature. PZT thin films were deposited on Pt/Ti/SiO$_{2}$/Si substrate at room temperature and 600.deg. C sequentially. The effect of the layer deposited at room temperature was investigated with regard to I-V characteristics and P-E hysteresis loop. In the case of the sample with the layer deposited at room temperature, both leakage current and dielectric constant were decreased. The thicker the layer deposited at room temperature was, the lower dielectric constant was. However, leakage current was indepenent of the variation of the thickness ratio. The sample with 200$\AA$ of the layer deposited at room temperature showed the most promising results in both dielectric constant and leakage current.
The electrical properties of TiM/TiSi$_{2}$ bilayer formed by rapid thermal anneal in NH$_{3}$ ambient after the Ti film is deposited on silicon cubstrate are investigated. N$^{+}$ contact resistance slightly increases with increasing annealing temperature with P$^{+}$ contact resistance decreases. The contact resistance of N$^{+}$ contance was less than 24[.OMEGA.] but P$^{+}$ thatn that of N$^{+}$ contact but the leakage current indicates degradation of the contact at high annealing temperature for both N$^{+}$ and contacts. The leakage current of N$^{+}$ Junction was less than 0.06[fA/${\mu}m^{2}$] but P$^{+}$ contact was 0.11-0.15[fA/${\mu}m^{2}$]. The junction breakdown voltage for N$^{+}$ junction remains contant with increasing annealing temperature while P$^{+}$ junction slightly decreases. The Electrical properties of a two step annealing are better than that of one step annealing. The Tin/TiSi$_{2}$ bilayer formed by RTA in NH$_{3}$ ambient reveals good electrical properties to be applicable at ULSI contact.
Recently, scaling down of ULSI (Ultra Large Scale Integration) circuit of CMOS (Complementary Meta Oxide Semiconductor) based electronic devices, the electronic devices, become much faster and smaller size that are promising property of semiconductor market. However, very narrow interconnect line width has some disadvantages. Deposition of conformal and thin barrier is not easy. And metallization process needs deposition of diffusion barrier and glue layer for EP/ELP deposition. Thus, there is not enough space for copper filling process. In order to get over these negative effects, simple process of copper metallization is important. In this study, Cu-V alloy layer was deposited using of DC/RF magnetron sputter deposition system. Cu-V alloy film was deposited on the plane SiO2/Si bi-layer substrate with smooth surface. Cu-V film's thickness was about 50 nm. Cu-V alloy film deposited at $150^{\circ}C$. XRD, AFM, Hall measurement system, and AES were used to analyze this work. For the barrier formation, annealing temperature was 300, 400, $500^{\circ}C$ (1 hour). Barrier thermal stability was tested by I-V(leakage current) and XRD analysis after 300, 500, $700^{\circ}C$ (12 hour) annealing. With this research, over $500^{\circ}C$ annealed barrier has large leakage current. However vanadium-based diffusion barrier annealed at $400^{\circ}C$ has good thermal stability. Therefore thermal stability of vanadium-based diffusion barrier is desirable for copper interconnection.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.