• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.10a
• /
• pp.630-633
• /
• 2021

Microphones can convert received voice signals to electric signals. They have been widely used in various industries such as radios, smart devices and vehicles. Recently, the demands for small size and high sensitive microphones are increased according to the minimization of wireless earphone with the development of smart phone. A MEMS system is a good candidate for an ultra-small size microphone of a next generation and a read out IC for high sensitive MEMS sensor is researched from many industries and academies. Since the microphone system has a high sensitivity from environment noise and electric system noise, the system requires a low noise power supply and some low noise design techniques. In this paper, a low noise LDO is presented for small size MEMS microphone systems. The input supply voltage of the LDO is 1.5-3.6V, and the output voltage is 1.3V. Then, it can support to 5mA in the light load condition. The integrated output noise of proposed LDO form 20Hz to 20kHz is about 1.9uV. These post layout simulation results are performed with TSMC 0.18um CMOS technology and the size of layout is 325㎛ × 165㎛.

• Korean Journal of Food Science and Technology
• /
• v.12 no.1
• /
• pp.53-58
• /
• 1980

The effects of water activity, oxygen, light and storage temperature on the color degradation of dried red pepper were investigated during storage. Some packing materials were used for improving the storage life of red pepper by minimizing those factors. The results obtained were summarized as follows: 1. The critical water activity to the capsanthin of red pepper was 0.75. 2. Color degradation of dried red pepper was the most severe by U.V. light among 100 watt infra-red lamp, 15 watt U.V. lamp and 200 watt glow lamp. 3. Effect of light was not significant in the presence of nitrogen, Main factor of color degradation of red pepper in storage appeared spontaneous oxidation by the existence of oxygen. 4. The capsanthin content and the lightness as hunter value in powder type storage of red pepper was higher than that in whole pod type during 3 month's storage. 5. The air and damp-proof packing materials showed better results than polyethylene film packing in capsanthin content and lightness during 3 month's storage.

• Nuclear Engineering and Technology
• /
• v.49 no.6
• /
• pp.1287-1300
• /
• 2017

Based on the observation that ignoring the angle dependency of multigroup resonance cross sections within a fuel pellet would result in nontrivial underestimation of the spatial self-shielding of flux, a parametrized spectral superhomogenization (SPH) factor library (PSSL) method is developed as a practical means of resolving the problem. Region-wise spectral SPH factors are calculated by the normal and transport corrected SPH iterations after ultrafine group slowing down calculations over various light water reactor pin-cell configurations. The parametrization is done with fuel temperature, U-238 number density, fuel radius, moderator source represented by ${\Sigma}_{mod}V_{mod}$, and the number density ratio of resonance nuclides to that of U-238 in a form of resonance interference correction factors. The parametrization is successful in that the root mean square errors of the interpolated SPH factors over the fuel regions of various pin-cells are within 0.1%. The improvement in reactivity error of the PSSL method is shown to be superior to that by the original SPH method in that the reactivity bias of -200 pcm to -300 pcm vanishes almost completely. It is demonstrated that the environment effect takes only about 4% in the reactivity improvement so that the pin-cell based PSSL method is effective in the assembly problems.

• Restorative Dentistry and Endodontics
• /
• v.20 no.2
• /
• pp.721-731
• /
• 1995

The purpose of this study was to evaluate the adaptability to tooth structure of light-cured glass ionomer cements. In this, study, class V cavities were prepared on the buccal surfaces of thirty extracted human premolar teeth, and they were randomly assigned into 3 groups with 10 teeth. The cavities of each groups were filled with the Fuji II LC(GC International Corp., Japan), Vitremer(3M Dental Products Division, U.S.A) and VariGlass VLC(Caulk/Dentsply Inc., U.S.A.). The specimens were immersed in 1% methylene blue solution and stored in 100% realtive humidity at $37^{\circ}C$ for 5 days. And then, the specimens sectioned buccolingually. Degree of eke penetration at tooth--restoration interfaces were examined by magnifying glass at occlusal and gingival margin. The results were as follows : 1. On the occlusal margin, among the experimental groups, the group 2 showed the lowest microleakage($1.40{\pm}1.17$) and the group 1 showed the highest microleakage($3.10{\pm}0.99$). There was significant difference between group 1 and group 2(P<0.01). 2. On the gingival margin, among the experimental groups, the group 2 showed the lowest microleakage($2.50{\pm}1.08$) and the group 1 showed the highest microleakage($3.50{\pm}0.84$). But there was not significant. difference among the experimental groups(P>0.05). 3. The degree of microleakage at occlusal margin was less than gingival margin in all experimental groups.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.2
• /
• pp.94-103
• /
• 1998

Recently, many researches are carried for high-speed and light craft. In this study, the optimum structural design procedure and the computer program are developed to minimize the hull weight of SES(Surface Effect Ship) built of composite materials. Three types of composite materials-Sandwich, Single Skin and Hybrid type- are considered and the efficiency of each type is investigated. In design process, the optimum design of main members is performed at first considering longitudinal strength. And then, the transverse member design is performed considering torsional strength SSDP(Structural Synthesis Design program) of U.S. Navy is adopted for design algorithm and DnV classification nile for design loads and strength criteria. For optimum structural design, ES 1+1 optimization technique is used.

• Journal of the Optical Society of Korea
• /
• v.13 no.1
• /
• pp.80-85
• /
• 2009

An experimental study of energy absorption and x-ray emission from ultrashort laser pulse irradiation of in-situ produced solid clusters has been performed. Silver clusters produced by a 30 mJ, 300 ps laser pulse were irradiated up to an intensity of $3{\times}10^{17}\;W/cm^2$ by a 70 mJ, 45 fs compressed laser pulse from the same Ti:sapphire laser. Absorption of the laser light exceeding 70% was observed, resulting in an x-ray yield (>1 keV) of ${\sim}60{\mu}J$ pulse. This may constitute a much simpler means of intense x-ray generation using ultrashort laser pulses as compared to the irradiation of structured / pre-deposited cluster targets, and it offers higher x-ray conversion efficiency than that from gas clusters and planar solid targets.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1719-1721
• /
• 2003

In this paper, electrical characteristics of inductively coupled plasma in an electrodeless fluorescent lamp were investigated using a Langmuir probe with a variation of Ar gas pressure. The RF output was applied in the range of 5-50W at 13.56MHz. The internal plasma voltage of the chamber and the probe current were measured while varying the supply voltage to the Langmuir probe in the range of -100V ${\sim}$ +100V. When the pressure of Ar gas was increased, electric current was decreased. There was a significant electric current increase when the applied RF power was increased from 10 W to 30 W. This implies that this method can be used to find an optimal RF power for efficient light illumination in an electrodeless fluorescent lamp.

• The KIPS Transactions:PartD
• /
• v.13D no.1 s.104
• /
• pp.125-132
• /
• 2006

The existing recognition system of license plates cannot get the satisfactory result in noise environments. The purpose of this paper is to propose an algorithm that can recognize the region of license plates accurately in a noise environment. The algorithm is formulated by reorganizing the U- and V-channels of YUV color space as YUV is insensitive to light and carries less data than RGB color information. The region of license plates has been extracted by the geometric characteristics, sizes, and places of labeling images. The proposed algorithm was found to improve the process of extracting the region of license plates in various noise environments.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.149-156
• /
• 2013

This paper presents a hardware edge detector of image signal at pixel level of CMOS image sensor (CIS). The circuit detects edges of an image based on a bump circuit combining with the pixels. The APS converts light into electrical signals and the bump circuit compares the brightness between the target pixel and its neighbor pixels. Each column on CIS 64 by 64 pixels array shares a comparator. The comparator decides a peak level of the target pixel comparing with a reference voltage. The proposed edge detector is implemented using 0.18um CMOS technology. The circuit shows higher fill factor 34% and power dissipation by 0.9uW per pixel at 1.8V supply.

• Journal of Fashion Business
• /
• v.19 no.4
• /
• pp.120-134
• /
• 2015

This study aimed to determine the physical properties of silk and nylon fabrics that are treated with persimmon juice in accordance with irradiation time of ultraviolet spectrum. Persimmon juice dyeing has the advantage of using the tannin component of the persimmon. Tannin plays an important role in inhibiting photodegradation of fibers or polymers. Among fibrous materials, silk and nylon are prone to deterioration by light. Hence, this study aimed to reduce these weaknesses of silk and nylon by applying persimmon juice treatment. We accordingly carried out investigation and experiments on ultraviolet irradiation, and physical characteristics of treated fabrics. The persimmon juice treatment process led to increased weight and thickness. In addition, the air permeability of silk fabric was increased, as compared to the control specimen; whereas, that of nylon fabric was decreased. Both drape stiffness and flex stiffness of silk and nylon tended to be high in textiles processed with persimmon juice treatment, as compared to the control textile. Peak load and elongation at peak load of untreated samples clearly decreased in both silk and nylon fabrics with the increase of ultraviolet irradiation time, while those of persimmon juice treated samples increased. Furthermore, ultraviolet blocking ratio measurement indicated that the fabric specimens treated with persimmon juice blocked U.V. spectrum better than the control specimen.