• 수산해양기술연구
• /
• 제19권1호
• /
• pp.51-56
• /
• 1983

경계요소법에 의하여 U자형 홈(groove)을 가진 평판이 측면 분포하중을 받을 때 끝부에 위치할 원형 Hole의 최적 위치의 해석을 행하고 동일한 모델(model)에 대하여 실험결과를 비교하여 다음과 같은 결론을 얻게 되었다. 1. 원형 Hole이 U자형 홈(groove)에 가까이 접근하게 됨에 따라 초기의 원형 Hole은 c.-c.선에 수직방향이 그 장축이 되는 타원형으로 변화됨을 알 수 있다. 2. 원형 Hole이 U-groove에 접근함에 따라 Hole 과 Groove 사이의 Neck부는 그 횡단면응력이 인장 및 압축이 동시에 존재하다가 점점 전체가 인장역이 됨을 알 수 있다. 3. 원형 Hole이 Groove에 접근함에 따라 판재경계와 Hole 사이의 목(neck)부분은 계속적인 압축상태를 유지한다. 4. U-groove쪽의 Neck area의 응력분포는 그 최대응력치가 Hole로 접근함에 따라 가속적으로 증가하고 Hole의 찌그러짐(distortion)의 방지를 위한 Hole의 최적중심의 위치는 Neck부의 Hole 측면의 압축응력치가 0이 되지 않는 범위가 한계임을 알 수 있다.

• Tribology and Lubricants
• /
• 제29권3호
• /
• pp.149-159
• /
• 2013

In this research, the lubrication characteristics of spool valves with various cross-sectional groove shapes were studied. The validity of using the Reynolds equation for the analysis of spool valves with various groove shapes was also investigated. The cross-sectional shapes for the grooves included a triangle, square, and U shape. The characteristics of the flow in the groove were investigated using streamlines. When the number of grooves was increased, the difference between the results obtained from the Reynolds equation and those obtained from the Navier-Stokes equation increased according to the groove shape. Thus, it was found that the Navier-Stokes equation should be used to investigate the lubrication characteristics of the spool valves in those cases. Moreover, in the case where the cross section of the groove was U-shaped, the groove prevented the small eddy current from occurring in the groove. Therefore, the lateral force and friction force of the spool valve with the U-shaped groove were lower than those of the spool valves with other groove shapes.

• 한국재료학회지
• /
• 제23권2호
• /
• pp.116-122
• /
• 2013

For fabricating silicon solar cells with high conversion efficiency, texturing is one of the most effective techniques to increase short circuit current by enhancing light trapping. In this study, four different types of textures, large V-groove, large U-groove, small V-groove, and small U-groove, were prepared by a wet etching process. Silicon substrates with V-grooves were fabricated by an anisotropic etching process using a KOH solution mixed with isopropyl alcohol (IPA), and the size of the V-grooves was controlled by varying the concentration of IPA. The isotropic etching process following anisotropic etching resulted in U-grooves and the isotropic etching time was determined to obtain U-grooves with an opening angle of approximately $60^{\circ}$. The results indicated that U-grooves had a larger diffuse reflectance than V-grooves and the reflectances of small grooves was slightly higher than those of large grooves depending on the size of the grooves. Then amorphous Si:H thin film solar cells were fabricated on textured substrates to investigate the light trapping effect of textures with different shapes and sizes. Among the textures fabricated in this work, the solar cells on the substrate with small U-grooves had the largest short circuit current, 19.20 mA/$cm^2$. External quantum efficiency data also demonstrated that the small, U-shape textures are more effective for light trapping than large, V-shape textures.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.148-151
• /
• 2003

The purpose of this study is to investigate the manufacturing technique on the U type Draw-Bending of inner groove tube. The U type tube requires the quality of product that satisfy sufficient conditions for a heat exchanger. The mandrel components act the important roles that prevent wrinkles and keep the shape of cross section of bended tube at bending process. We performed the FEM simulation using LS-DYNA software and the bending test of inner groove tube and then, compared bending simulation with bending test results about mandrel ball diameter, mandrel position and optimal clearance between mandrel and tube.

• 유공압시스템학회논문집
• /
• 제4권4호
• /
• pp.15-20
• /
• 2007

All of the hydraulic spool valves adopt radially grooved spools to avoid hydraulic locking. In this paper, a commercial computational fluid dynamics (CFD) code, FLUENT is used to investigate the accurate Poiseuille flow characteristics inside single groove. The stream lines, velocity and pressure distributions are obtained for various groove widths, depths and shapes. The stream lines are highly affected by groove shape and there occurred large vortexes inside groove beyond a certain ratio of groove width to depth. Especially the U shaped groove restrains the occurrence of vortex. Therefore the numerical method adopted in this paper can be use in optimum designing of multi-grooved hydraulic spool valves.

• 대한기계학회논문집B
• /
• 제25권2호
• /
• pp.260-268
• /
• 2001

Wake structures behind two circular cylinders with different groove configurations(U and V-shape) have been investigated experimentally. The results were compared with those for the smooth cylinder having the same diameter D. The drag force, mean velocity and turbulent intensity profiles of wake behind the cylinders were measured with varying the Reynolds number in the range of Re(sub)D=8,000∼14,000. As a result, the U-shaped groove was found to reduce the drag up to 18.6%, but the V-shaped groove reduced drag force only 2.5% compared with the smooth cylinder. As the Reynolds number increases, the vortex shedding frequency becomes a little larger than that of the smooth cylinder. The visualized flow using the smoke-wire and particle tracing methods shows the flow structure qualitatively.

• 한국진공학회지
• /
• 제11권4호
• /
• pp.249-255
• /
• 2002

이방성 습식 식각기술을 이용하여 멤버레인을 제작하기 위하여 KOH 용액 및 KOH-IPA 혼합용액을 사용하여 단결정 실리콘 기판을 식각하였다. 단결정 실리콘의 식각속도는 식각 용액의 온도와 농도에 좌우되었으며, 식각 용액의 농도에 따라 식각 형태와 패턴 형성 방향이 달라짐도 관찰되었다. 식각을 위한 표면패턴은 실리콘웨이퍼의 primary flat에 $45^{\circ}$로 기울여 형성되었으며 KOH의 농도가 20 wt%로 유지되었을 때, 식각 용액의 온도 $80^{\circ}C$ 이상에서는 U-groove, $80^{\circ}C$ 이하의 온도에서는 V-groove 식각 형태가 형성되었다. 각 면에 대한 식각속도 차이에 의해서 생기는 hillock은 온도와 농도가 높아짐에 따라 현저하게 줄어들었다.

• 대한기계학회논문집A
• /
• 제20권1호
• /
• pp.154-162
• /
• 1996

Ball screws are commonly used in linear motion feeding systems of various machine tools and automated systems. They are known to have relatively little backlash, high precision and efficiency compared to ordinary lead screws. Furthermore, the effectiveness of ball screw has made it the preferred choice of many newly developed high speed precision feeding units. The motivation of this work is to establish the groove edsigh basis of ball screws for the reduction of contact fatigue failure. In most instances, fatigue failure between ball and shaft groove is due to excessive contact pressure. Especially, the excessive load is causative of plastic flow below the contact surface, which can contribute to surface failure. But, in spite of small load, if groove conformity rate is large, contact pressure is increased and internal shear stress reach the yield value of the material. In such a point, the authors deal with design procedure for deciding the permissible conformity rate of a ball screw groove with the computational evaluation of contact pressure and maximum shear stress.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.425-426
• /
• 2008

Elasto-plastic finite element analysis was carried out for analyzing the severe plastic deformation behavior of copper specimens during groove pressing. Deformation localization was studied in terms of strain variations along the longitudinal direction. Plastic strain is lower at the local interface between the shear and the flat regions, which receive very little shear during the pressing cycle. Strain localization is more intensified with the number of rove pressing cycles, although the average strain level increases.

• 대한치과기공학회지
• /
• 제42권3호
• /
• pp.220-227
• /
• 2020

Purpose: This study aims to investigate the cusp variation pattern of the Korean mandibular second premolar and to determine the difference in tooth diameter and surface area using a virtual three-dimensional model. Methods: Dental casts from 69 students were scanned as a virtual dental models with a three-dimensional dental model scanner. Tooth diameter, absolute and relative individual areas, total crown area, the number of lingual cusps and central groove pattern were analyzed using RapidForm 2004. The Mann-Whitney U-test and the Kruskal-Wallis test were performed to verify sexual dimorphism, the difference in tooth diameter and surface according to the cusp variation pattern (α=0.05). Results: There was no significant difference except in buccolingual diameter (p<0.05) and buccolingual diameter at the cervix (p<0.05). The relative surface area of the total clinical crown was 65.76% for the buccal half and 34.24% for the lingual half, with a ratio of 2:1. In the case of the presence of two lingual cusps, the ratio was 21.47% for the mesiolingual half and 14.12% for the distaolingual half, with a ratio of 3:2. The dominant central groove patterns of the second premolar were the H-pattern (42.0%), followed by the Y-pattern (37.7%), then the U-pattern (20.3%). The relative buccal half was largest in the U-pattern central groove and the relative lingual half was largest in the Y-pattern central groove (p<0.05). Conclusion: This study is significant in that it measured quantitative surface areas and the findings could be a meaningful reference to comprehend dental anatomy in Koreans.