• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.6
• /
• pp.1281-1286
• /
• 2012

In the information age, internet was developed from the wired access to the wireless Internet access. When a surge in demand for wireless Internet access, efficiency and performance of 2.4GHz band which leads to saturation of the communication was significantly fall. in this paper, the U-slot microstrip array antenna in the 5 GHz band have been studied to improve the drawback of a narrow bandwidth of the T-slot micro strip antenna. The characteristics of single antenna and array antenna was investigated to obtain the optimum frequency properties. The optimal U-slot microstrip array antenna possibility was confirmed.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.3
• /
• pp.9-14
• /
• 2020

In this paper, Qualification Model of frequency synthesizer is designed for X-band SAR system and performed electrical and environment test. Designed frequency synthesizer generate 13.65 GHz with very low phase noise performance. The integrated phase noise from 10Hz to 1MHz is -37.91 dBc. IRF performances are analyzed according to phase noise and jitter. Also, thermal and structure analysis are achieved for stable operation in space environment. Designed frequency synthesizer is consist of 2 modules of 6U size and generate L-band, C-band, Ku-band. The result of this study would enhance the design ability of RF module and help the frequency synthesizer design for SAR payload system.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.07a
• /
• pp.162-163
• /
• 2002

1-D photonic band-gap structure is identified in a cholesteric liquid crystal system. The optical transmission spectrum is measured and compared with the theoretical analysis. Nonlinear transmission is measured near the band edge. Also 3-D photonic band-gap structures are fabricated from dielectric colloidal polystyrene beads through a centrifuge method. The fabricated photonic crystals exhibit opalescent colors under white light and show a clear diffraction peak dependent on the incident angle of the light beam. Also the scanning electron microscope image was taken to verify the face-centered cubic crystal structure. Bragg's law and Snell's law are employed to describe the position of angle resolved diffraction peaks. It was shown that the optically deduced effective refractive index and lattice constants were in good agreement with the crystal structure identified by scanning electron microscope.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1561_1562
• /
• 2009

In this paper, designed triple-band antenna of PIFA(Planar Inverted-F Antenna) structure with U-slot. We designed optimal PIFA structure using Evolution Strategy(ES) about two U-slot parameters. We materialized API(Application Program Interface) about EM simulator and Excel using VB(Visual Basic). The result of ES for triple-band PIFA are resonant frequency of 430MHz, 910.5MHz, 2458.5MHz.

• Honam Mathematical Journal
• /
• v.45 no.4
• /
• pp.598-609
• /
• 2023

The purpose of this article is to obtain the spectrum, fine spectrum, approximate point spectrum, defect spectrum and compression spectrum of the double band matrix U (a₀, a₁, a₂; b₀, b₁, b₂), b₀, b₁, b₂≠0 on the sequence space ℓ_p (1 < p < ∞).

• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.485-492
• /
• 2006

The AA5182/polypropylene/AA5182(AA/PP/AA) sandwich sheets have been developed for application to automotive body panels in future lightweight vehicles with significant weight reduction. It has been reported that the AA5182 aluminum sheet shows $L\"{u}ders$ band because of dissolved Mg atoms that cause fabrication process problem, especially surface roughness. The examination of serration behavior has been made after the tensile deformation of the AA/PP/AA sandwich sheets as well as that of the AA5182 aluminum skins at room and elevated temperatures. All sandwich sheets and the AA5182 aluminum skin showed serration behavior on their flow curves. However, the magnitude of serration was significantly diminished in the sandwich sheet with high volume fraction of the polypropylene core. According to the results of the analysis of the surface roughness following the tensile test, $L\"{u}ders$ band depth of the sandwich sheet evidently showed lower than that of the AA5182 aluminum skin. The strain rate sensitivity, m-value, of the AA5182 aluminum skin was -0.006. By attaching these skins to the polypropylene core, which has relatively large positive value of 0.050, m-value of the sandwich sheets changed to the positive value. The serration mechanism of the sandwich sheets was quantitatively investigated in the point of the effect on polypropylene thickness variation, that on the strain rate sensitivity and that on the localized stress state.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.57-66
• /
• 2006

AA5182-polypropylene sandwich sheet was manufactured, and the mechanical properties evaluation was executed in order to identify $L{\ddot{u}}ders$ band that causes fabrication process problem and especially surface roughness. To identify formability, deformation behavior, plastic strain ratio (R-value) and pole figure were measured, and texture analysis was performed. In the case of sandwich sheet, the unstable deformation behavior has decreased. As well, for sandwich sheet, A1 skin could manage the most of load, and the elongation has improved about 45% more than that of A1 skin. The plastic strain ratio of A1 skin and sandwich panel, which indicates serration behavior, was obtained from instantaneous plastic strain ratio evaluation. Also, the planar anisotropy of sandwich sheet has decreased more than that of A1 skin. According to these results, the sandwich sheet produced lightening effect and could control unstable deformation characteristic, that is, surface roughness caused by $L{\ddot{u}}ders$ band. Furthermore, it was proved that the texture control of the rolling attachment of A1 skin is necessary to improve the formability of the sandwich panel.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.6A
• /
• pp.414-424
• /
• 2003

In this paper, a multiple U-shaped slot antenna for 5.25㎓~5.35㎓ is designed, fabricated, and measured. The prototype consists of U-slot and two invert U-slot. To obtain enough bandwidth, the foam layer is inserted between ground plane and substrate. Important parameters in the design are U-slot length, width, position, airgap length, and feed point. From these parameters optimized, a multiple U-shaped slot antenna is fabricated and measured. The measured results of the antenna are compared with its simulated results. The resonant frequency of the fabricated multiple U-shaped slot antenna is 5.25㎓ the bandwidth for approximately 7.4%(VSWR<1.5) and the gain is 2.9~5.3dBi. The experimental far-field patterns are stable across the pass band. The 3dB bandwidth in H-Plane and I-Plane are 62$^{\circ}$ and 50$^{\circ}$, respectively.

• 한국ITS학회:학술대회논문집
• /
• v.2006 no.10
• /
• pp.175-178
• /
• 2006

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2A
• /
• pp.195-201
• /
• 2004

In this paper, U-Shaped slot Bow-Tie antenna for 5.15㎓∼5.35㎓ is designed, fabricated, and measured. The prototype consist of U-Shaped slot. To obtain suitable bandwidth, the form layer is inserted between ground plane and substrate. Important parameters in the design are U-slot length, width, position, air-gap height, and feed point position. From these parameters optimized, a U-shaped slot Bow-Tie antenna is fabricated and measured. The measured results of the antenna are obtained as follows results. The resonant frequency of the Fabrication U-shaped slot Bow-Tie antenna is 5.28㎓, bandwidth for approximately 7.76％(VSWR<1.2) and the gain is 4∼7dBi. The experimental far-field patterns are stable across the pass band. The 3dB bandwidth in Elevation and Azimuth are 73.63$^{\circ}$and 65.08$^{\circ}$, respectively.