• Geomechanics and Engineering
• /
• 제21권5호
• /
• pp.461-469
• /
• 2020

The objective of this paper is to study the deformation in a homogeneous isotropic modified couple stress thermoelastic medium with and without energy dissipation and with two temperatures due to thermal source and mechanical force. Laplace and Fourier transform techniques are applied to obtain the solutions of the governing equations. The displacement components, stress components, conductive temperature and couple stress are obtained in the transformed domain. Isothermal boundary and insulated boundary conditions are used to investigate the problem.The effect of two temperature and GN theory of type-II and type-III has been depicted graphically on the various components. Numerical inversion technique has been used to obtain the solutions in the physical domain. Some special cases of interest are also deduced.

• Journal of Korea Foundry Society
• /
• 제29권6호
• /
• pp.270-276
• /
• 2009

After casting button-type small ingots of ternary Fe-Mn-S alloys which had three different Mn/S ratios (1, 5 and 70) in a vacuum arc furnace, the effect of the ratio on the sulfide formation was investigated. In case of the Mn/S ratio of 1, if alloy composition was located in an iron-rich corner on a Fe-Mn-S ternary phase diagram, only duplex MnS-FeS sulfide films were observed in the grain boundary. If the alloy composition was located in the miscibility gap area of the phase diagram, primary globular dendritic sulfides and dendritic sulfide slags were generated within the grain and tubular monotectic sulfides were also detected in the grain boundary. When the Mn/S ratio was 5, if the alloy composition was in the iron-rich corner, only bead-like sulfides were generated. On the other hand, if the composition was in the miscibility gap area, globular dendritic sulfides and dendritic sulfide slags were generated in the form of primary sulfide inclusions and rod-like eutectic sulfides were observed in the grain boundary. Especially, if the contents of Mn and S increased more in the miscibility gap area of the phase diagram, primary globular sulfides containing iron intrusions were observed. In case of Mn/S ratio of 70, if the contents of Mn and S was decreased in the Fe corner of the phase diagram, only bead-like sulfides were observed in the grain boundary. Despite the composition was outside the miscibility gap area of the phase diagram, if the contents of Mn and S increased, clusters of fine sulfide particles as well as fine spherical primary monophase sulfides were observed in the grain boundary.

• Journal of Korean Institute of Industrial Engineers
• /
• 제25권1호
• /
• pp.8-20
• /
• 1999

In this paper, a design and estimation procedure for the stochastically dependent nonstationary multiple acceptance sampling plans is developed. At first, the rough-cut acceptance and rejection numbers are given as an initial solution from the corresponding sequential sampling plan. A Monte-Carlo algorithm is used to find the acceptance and rejection probabilities of a lot. The conditional probability formula for a sample path is found. The acceptance and rejection probabilities are found when a decision boundary is given. Several decision criteria and the design procedure to select optimal plans are suggested. The formula for measuring performance of these sampling plans is developed. Type I and II error probabilities are also estimated. As a special case, by setting the stage size as 1 in a dependent sampling plan, a sequential sampling plan satisfying type I and II error probabilities is more accurate and a smaller average sample number can be found. In a numerical example, a Polya dependent process is examined. The sampling performances are shown to compare the selection scheme and the effect of the change of the dependency factor.

• 한국해양학회지
• /
• 제18권2호
• /
• pp.142-148
• /
• 1983

In order to understand the circulation dynamics of the Keum River estuary, an extensive study was conducted; (i) variability of salinity boundary layer (ii) fluid dynamic characteristics (iii) tides and tidal currents (iv) circulation, diffusion, and dispersion (v) numerical modelling. As first part of this series of work, the salinity data obtained at six sites by using instantaneous profil]ing technique were analyzed in detail. it is found that the amplitude of salinity variation increases toward the upstream direction and its magnitude is greater at neap tide than spring tide. And also duration of salinity boundary layer is much longer during the neap tide than the spring tide, As a result of this study, the Keum River estuary is classified as a typical standing wave type estuary. Finally, we present a schematic diagram for the duration of the salinity boundary layer, which will be useful for further study on flocculation phenomena and sedimentation dynamics.

• Journal of the Korean Ceramic Society
• /
• 제22권5호
• /
• pp.54-60
• /
• 1985

This study is concerned with the mechanism of PTCR in $BaTiO_3$ ceramics doped by $Nb^{+5}$ Since the vacancy compensation layer at the grain boundary of n-type doped $BaTiO_3$ ceramics has been known as a major factor for surface state to give PTCR phenomena the dependence of PTCR on such vacancy compensation layer was attemped to be confirmed experimentally in this study. For the experiment quenching and annealing at various temperature after sintering were adopted to induce difference in the thickness of vacancycompensation layer so as to exihibit difference of PTCReffect eachother. The TEX>$Ba^{++}$ cocentration at the grain and grain boundary was measured by EDAX to confirm the formation of the vacancy compensation layer. It was found that i)either decrease in the temperature for quenching ii) or increase in the temperature for annealing improves the PTCR effect clearly iii)increase in TEX>$Ba^{++}$ concentration at the grain boundary results in the improvement of PTCR effect. It was concluded that all the experimental results gave the evidence for the dependence of PTCR effect on the vacancy compensation layer at the grain boundary which had been induced possibly by the $Ba^{++}$ diffusion by the heat treatment conducted.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제21권2호
• /
• pp.329-340
• /
• 1997

A passive control of interaction of condensation shock wave / boundary layer for reducing the strength of condensation shock was conducted experimentally in a 2.5 * 8 cm$^{2}$ indraft type supersonic wind tunnel. The effects of following factors on passive control were investigated: 1) the thickness of porous wall, 2) the diameter of porous hole, and 3) the orientation of porous hole. On the other hand, the location of nonequilibrium condensation region and condensation shock wave was controlled by regulation of the stagnation conditions. Surface static pressure measurements as well as Schlieren observations of the flow field were obtained, and their effects were compared with the results the cases of without passive control. It was found that thinner porous wall, smaller porous hole and FFH orientation for the same cavity size and porosity of 12% are more favourable than the cases of its opposite.

• Journal of Mechanical Science and Technology
• /
• 제20권7호
• /
• pp.1051-1058
• /
• 2006

The steady aerodynamic characteristics of a wing flying over a channel are investigated using a boundary-element method. The present method is validated by comparing the computed results with the measured data. Compared with a flat ground surface, the channel fence augmented the lift increase and induced drag reduction. When the fence is lower than the wing height, the gap between the wingtip and the fence does not affect the aerodynamic characteristics of the wing much. When the fence is higher than the wing height, the close gap increased the lift. The induced drag is reduced when the wing is placed near the ground or at the same height as the fence. It is believed that present results can be used in the conceptual design of the high-speed ground transporters flying over the channel.

• Bulletin of the Society of Naval Architects of Korea
• /
• 제12권1호
• /
• pp.9-22
• /
• 1975

As a second step of a thermal stress analysis in a watertight bulkhead plate during welding of a spool type penetration piece, is idealized as a thin circular disk with a clamped boundary. The exact solution for the transient temperature distribution and associated quasi-static thermal stresses which arise in a circular disk subjected to an instantaneous point source of heat acting in its interior has been obtained. And the solutions have been extended to the case of moving source of heat with the aid of the Duhamel's superposition integral and the results finally derived have been compared with the other results from the typical cases. The solutions can be applied to the problem such as a welding of a penetration piece on the watertight bulkhead and also applicable to the problems which occur in cutting or welding.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제34권2호
• /
• pp.166-179
• /
• 2008

Excessive concentration of stress which is occurred in occlusion around the implant in case of the implant supported fixed partial denture has been known to be the main cause of the crestal bone destruction. Therefore, it is essential to evaluate the stress analysis on supporting tissue to get higher success rates of implant. The purpose of this study was to evaluate the effects of stress distribution and deformation in 3 different types of three-unit fixed partial denture sup-ported by two implants, using a three dimensional finite element analysis in a three dimensional model of a whole mandible. A mechanical model of an edentulous mandible was generated from 3D scan, assuming two implants were placed in the left premolars area. According to the position of pontic, the experiments groups were divided into three types. Type I had a pontic in the middle position between two implants, type II in the anterior posi-tion, and type III in the posterior position. A 100-N axial load was applied to sites such as the central fossa of anterior and posterior implant abutment, central fossa of pontic, the connector of pontic or the connector between two implants, the mandibular boundary conditions were modeled considering the real geometry of its four-masticatory muscular supporting system. The results obtained from this study were as follows; 1. The mandible deformed in a way that the condyles converged medially in all types under muscular actions. In comparison with types, the deformations in the type II and type III were greater by 2-2.5 times than in the type I regardless of the loading location. 2. The values of von Mises stresses in cortical and cancellous bone were relatively stable in all types, but slightly increased as the loading position was changed more posteriorly. 3. In comparison with type I, the values of von Mises stress in the implant increased by 73% in Type II and by 77% in Type III when the load was applied anterior and posterior respectively, but when the load was applied to the middle, the values were similar in all types. 4. When the load was applied to the centric fossa of pontic, the values of von Mises stress were nearly $30{\sim}35%$ higher in the type III than type I or II in the cortical and cancellous bone. Also, in the implant, the values of von Mises stress of the type II or III were $160{\sim}170%$ higher than in the type I. 5. When the load was applied to the centric fossa of implant abutment, the values of von Mises stress in the cortical and cancellous bone were relatively $20{\sim}25%$ higher in the type III than in the other types, but in the implant they were 40-45% higher in the type I or II than in the type III. According to the results of this study, musculature modeling is important to the finite element analysis for stress distribution and deformation as the muscular action causes stress concentration. And the type I model is the most stable from a view of biomechanics. Type II is also a clinically accept-able design when the implant is stiff sufficiently and mandibular deformation is considered. Considering the high values of von Mises stress in the cortical bone, type III is not thought as an useful design.

• Water for future
• /
• 제10권1호
• /
• pp.95-100
• /
• 1977

The empirical area-reduction method by W.M. Borland and C.R. Miller and its revised procedure by W.T. Moody were made of fitting the area and storage curves to the Van't Hul distributions. It should be noted that the reservoir is classified into one of the four standard types on the basis of the topographical feature of the reservoir in application of the method. In other words, this method did not take into account several considerafble factors affecting the mode of sediment deposition, but only the shape of the reservoir as a governign factor. This is why the method occasionally creates ambiguity in classification and accordingly leads to unexpected mode of deposition. This paper describes a generating an formula to decide the standard classification of four types Van's Hul distributions, taking into consideration quantitatively sediment-loss percent and capacity-inflow ratio as well as the shape of the reservoirs by multiple regression analysis using the least square method to get a better fit to the design curves. The result is expressed as $Y=-1.95+55.8X_1+0.14X_2+0.12X_3$ in which the the values of Y locate the standard type I through type IV in the range from ten to forty with the interval of ten. The regression analysis was correlated well with the standard errors of estimate of around two except for the case of the type IV. This formula does not give big difference from the Borland's work in general sityation, but it demonstrates acceptable results, giving somewhat precise replys for the specific reservoirs. Its application to the Soyang Lake, one of the largest reservoirs in the country, defined clearly the type II, while the original method located it in the boundary of the type II and type III.