• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.6
• /
• pp.535-542
• /
• 2013

To enhance the performance of SEWGS system by holding the WGS catalyst in a SEWGS reactor using bed inserts, effect of bed insert geometry on CO conversion of WGS catalyst was measured and investigated. Small scale fluidized bed reactor was used as experimental apparatus and tablet shaped WGS catalyst and sand particle were used as bed materials. The cylinder type and the spring type bed inserts were used to hold the WGS catalysts. The CO conversion of WGS catalyst with the change of steam/CO ratio was determined based on the exit gas analysis. Moreover, gas flow direction was confirmed by bed pressure drop measurement for each case. The measured CO conversion using the bed inserts showed high value comparable to previous results even though at low catalyst content. Most of input gas flowed through the bed center side when we charged tablet type catalyst into the cylinder type bed insert and this can cause low $CO_2$ capture efficiency because the possibility of contact between input gas and $CO_2$ absorbent is low in this case. However, the spring type bed insert showed good reactivity and good distribution of gas, and therefore, the spring type bed insert was selected as the best bed insert for SEWGS process.

• Korean Journal of Agricultural Science
• /
• v.5 no.2
• /
• pp.49-55
• /
• 1978

In order to get healthy seedling of rice suitable for rice transplanter, the growing characteristics of the seedling grown under different growing days and sowing densities were invesigated and the results obtained were summarized as follows; In the 20 days old seedling, the difference of growing state of seed ling and its characteristics between the two types of nursery bed was not found, but for the 30 days old seedling, both of the crop growth rate and the relative growth rate on the band-type nursery bed appeared higher than those on the mat-type nursery bed. And also, "the dry weight, the content of cardohydrate and the ratio of dry weight to plant height of the seedling grown on the band-type nursery bed were much higher than those on the mat-type nursery bed, however the amount of difference of seedling characteristics between two types of nursery bed was decreased for 40 days old seedling and leaf number was not increased. The amount of the seedling growth was increased with less density of sowing and for the difference between the higher and the less density, the difference getting bigger with the longer nursery days. The maximum density of sowing was approximately 200cc per nursery case on the band-type nursery bed and 250cc per nursery case on the mat-type nursery bed. It was seemed that the growing uniformity of the seedling grown on the mat-type nursery bed was better than that on the band- type nursery bed, As the coefficient of variation of the plant height and the leaf numbers of the seedling grown on the band- type nursery bed was higher than that on the mat-type nursery bed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.8
• /
• pp.1172-1179
• /
• 2022

This paper describes a design of point scalar multiplier for public-key cryptography based on binary Edwards curves (BEdC). For efficient implementation of point addition (PA) and point doubling (PD) on BEdC, projective coordinate was adopted for finite field arithmetic, and computational performance was improved because only one inversion was involved in point scalar multiplication (PSM). By applying optimizations to hardware design, the storage and arithmetic steps for finite field arithmetic in PA and PD were reduced by approximately 40%. We designed two types of point scalar multipliers for BEdC, Type-I uses one 257-b×257-b binary multiplier and Type-II uses eight 32-b×32-b binary multipliers. Type-II design uses 65% less LUTs compared to Type-I, but it was evaluated that it took about 3.5 times the PSM computation time when operating with 240 MHz. Therefore, the BEdC crypto core of Type-I is suitable for applications requiring high-performance, and Type-II structure is suitable for applications with limited resources.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.04a
• /
• pp.485-492
• /
• 2000

In the rail facilities the rail track consists of rail tie fastening accessories and bed,. The rail track is largely divided into Ballast Bed Track(BBT) and Concrete Bed Track(CBT) according to the type of bed. In this thesis among Concrete Bed Track slab track which is used for the Japanese high speed railway is a target of this study. Dynamic analysis by using finite element method are performed. where moving rain load is periodic function. Then through parametric study some conclusions are obtained as follow. Cement Asphalt Mortar(CAM) affects contrary mechanical behavior to rail and slab greatly. Therefore change of CAM spring coefficient should be handled with care, For slab thickness thin slab is more profitable to reduction of vibration of rail than thick one but mechanical capacity of slab is deteriorated, Improved structural type is proposed then structural analysis is performed for this one. This type is effective to reduction of vibration of railway system.

• Journal of the Korean Society of Combustion
• /
• v.7 no.1
• /
• pp.52-57
• /
• 2002

A numerical investigation using a commercial CFD program of the Inter-Phase Slip Algorithm has been carried out for detail characteristics of particle motions and bubble behaviors in a two dimensional fluidized bed. The bed simulated has been operated with three different distributor geometries, such as bubble cap, nozzle, and perforated plate types. Experiments using a slit-type two-dimensional fluidized bed and a cylinder-type fluidized bed have been performed in order to confirm the simulation model. In addition, the numerical results are compared with the wellknown correlation of bubble sizes and bubble rising velocities by Mori and Wen [1]. The simulation model that we applied is shown to be useful to understand the relation between bubble behaviors and distributor geometries.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.9 no.3
• /
• pp.165-171
• /
• 2014

In this paper, we propose the hardware and software of a test-bed of a hovering AUV (autonomous underwater vehicle). Test-bed to develop as the underwater robot for the hovering -type is planning to apply for marine resource development and exploration for deep sea. The RTU that controls a azimuth thruster and a vertical thruster of test-bed is a intergrated-type thruster. The main control unit that collects sensor's data and performs high-speed processing and controls a movement of test-bed is a underwater hybrid navigation system. Also it transfers position, posture, state information of test-bed to the host PC of user using a wireless communication. The host PC checks a test-bed in real time by using a realtime monitoring system that is implemented by LabVIEW.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.493-598
• /
• 2000

In the rail facilities, the rail track consists of rail, tie, fastening, accessories and bed. The rail track is largely divided into Ballast Bed Track (BBT) and Concrete Bed Track (CBT) according to the type of bed. In this thesis, among Concrete Bed Track, slab track, which is used for the Japanese high speed railway, is a target of this study. Dynamic analysis by using finite element method are performed where moving train load is periodic function. Then through parametric study, some conclusions are obtained as follows. Cement Asphalt Mortar (CAM) affects contrary mechanical behavior to rail and slab greatly. Therefore, change of CAM spring coefficient should be handled with care. For slab thickness, thin slab is more profitable to reduction of vibration of rail than thick one but mechanical capacity of slab is deteriorated. Improved structural type is proposed, then structural analysis is performed for this one. This type is effective to reduction of vibration of railway system.

• Journal of Radiation Protection and Research
• /
• v.38 no.4
• /
• pp.242-245
• /
• 2013

Monte Carlo method was applied to discriminate the external contamination on radiation workers in nuclear power plants for internal dose assessment generally used with a bed type scanning detector whole body counter. Korean voxel model with internal contamination was used to estimate the detection patterns of whole body scanning. Also, the BOMAB model with various external contamination was assumed to compare with detection of radionuclides inside the human body. From the comparison of detection efficiency between front and back side up, external contamination was easily distinguished.

• Korea Journal of Hospital Management
• /
• v.26 no.3
• /
• pp.68-83
• /
• 2021

Background: It is widely acknowledged that single bedrooms have many potential advantages compared to multiple bedrooms. However, Korea has a reimbursement system that patients have to pay the additional fee if they will use single bedroom or pay-bed (1-3 bedroom). There is little research on patients' bed selection and relationship between patient satisfaction and bed type in the Korean setting. Methods: Using the 2017 Korea Health Panel (KHP) Survey data, we modified bed type by two dichotomous variables: single bedroom vs. multiple bedroom (2+ bedrooms) and pay-bed (1-3 bedroom) vs. reimbursed bed (4+ bedroom). Multivariate logistic regression is performed to determine the factors affecting the patient's choice of room types. Multivariate regression analysis was conducted to examine how hospital room types are affecting patient satisfaction. Results: Single room and pay-bed (1-3 bedroom) use was influenced by patient age (19- years old), male, a person at work, hospitalizing in a clinic, and birth. After controlling variables of the behavioral model of medical utilization, the association between patient satisfaction and use of single bedroom & pay-bed (1-3 bedroom). Cause of hospitalization, major treatment, and recognition of unnecessary care are statistically significant variables on patient satisfaction. Conclusion: Although the single room is about the standard for newly built hospitals in western countries, it remains unclear that single room or pay-bed (1-3 bedroom) has positive effects on patient's outcomes and satisfaction. In this empirical study, the difference in patient satisfaction by bedroom type was not noticeable. In terms of bed management by hospital staff, securing patient credibility in hospital care is an important task. Patients' perception of whether medical staffs have encouraged unnecessary treatment or tests has a significant impact on patient's satisfaction.

• The Korean Journal of Mycology
• /
• v.50 no.3
• /
• pp.161-171
• /
• 2022

The edible paddy straw mushroom Volvariella volvacea (Bull. ex F.) Singer has high nutritional and medicinal values. They are grown on a wide variety of agricultural by-products using different several methods. The result of this present study showed that type of bed and cultivation condition (outdoor/indoor) had effects on the yield of paddy straw mushrooms grown on the spent oyster mushroom sawdust. The treatment of circular compact bed under indoor cultivation condition (CYIC) had the best yield and biological efficiency (B.E.) with 2,119.2 g/bed and 14.5%, respectively, followed by the treatment of conventional bed under outdoor cultivation condition (COOC) with the yield and B.E. of 1,935.5 g/bed and 13.2%, respectively, but the lowest yield and B.E. were observed in the treatment of conventional bed under indoor cultivation condition (COIC) with 1,226.1 g/bed and 8.4%, respectively. Paddy straw mushrooms cultivated on spent oyster mushroom sawdust should be proper in both outdoor and indoor conditions by conventional and circular compact methods as well. However, in indoor conditions, paddy straw mushrooms should be grown in a circular compact bed to ensure the temperature of the bed is suitable for the mushroom growth.