• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.57-60
• /
• 2005

Composite-to-aluminum joins were tested to get failure loads and modes for three types of joins; adhesive bonding, bolt fastening, and adhesive-bolt hybrid joining. Film type adhesive FM73 and paste type adhesive Cytec EA9394S were used for aluminum and composite bonding to make a double-lap joint. A digital microscope camcorder was used to monitor the failure initiation and propagation. It was found that the hybrid joining is an effective method to strengthen the joint when the mechanical fastening is stronger than the bonding as in the case of using the paste type adhesive. On the contrary, when the strength of the bolted joint is lower than the strength of the bonded joint as in the joint with the film type adhesive, the bolt joining contribute little to the hybrid joint strength.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.553-556
• /
• 2003

This study is analyzed about the factor of adhesive strength characteristics, curing time, asphalt application, test temperature which are liquid waterproofing membrane of rubber-asphalt and chloroprene-rubber type for concrete bridge deck. According to the results, curing time is shorter, adhesive strength is less in chloroprene-rubber type. And also chloroprene-rubber and rubber-asphalt type are showed high adhesive strength in low temperature.

• 약학회지
• /
• 제43권4호
• /
• pp.447-457
• /
• 1999

The purpose of this study is to prepare the adhesive type patch containing flurbiprofen, and to demonstrate the feasibility of flurbiprofen administration through the intact skin using adhesive type patch preparation. For this purpose, two pressure sensitive adhesives, Polyisobutylene(PIB) and $Gelva^{\circledR}737$, were selected from the chemical grade of polymers, and the adhesive type patches of flurbiprofen were prepared. The release rate of flurbiprofen from the PIB-based adhesive patch was higher than that from $Gelva^{\circledR}737$ based adhesive patch. The release rate of flurbiprofen from the PIB-based A-type patch with 1.0mm, 1.5mm or 2.0mm thicknesses followed the first order kinetics. In the skin permeation study, using male hairless mouse skin, a monophasic skin permeation profile was observed with 1% flurbiprofen loading dose. The inclusion of palmitic acid or SLS(0.25~0.5%) as an enhancer produced a remarkable enhancement in the skin permeation rate of flurbiprofen, and the percentile ratio of drug and enhancer appeared to be important for the effective enhancement. In the in vivo percutaneous absorption study, the plasma concentration of the optimal formulation was significantly (p<0.01) higher than that of the conventional cataplasma ($Bifen^{\circledR}$). These studies demonstrate a good feasibility of flurbiprofen administration through the intact skin using a transdermal patch, and show a possibility of the development of flurbiprofen patches.

• 비파괴검사학회지
• /
• 제32권2호
• /
• pp.122-130
• /
• 2012

Adhesive bend and shear tests of micro-sized bonded component have been performed to clarify the relationship between effects of heat-treatment on the adhesive strength and the bonded specimen shape using Weibull analysis. Multiple micro-sized SU-8 columns with four different diameters were fabricated on a Si substrate under the same fabrication condition. Heat-treatment can improve both of the adhesive bend and shear strength. The improvement rate of the adhesive shear strength is much larger than that of the adhesive bend strength, because the residual stress, which must change by heat-treatment, should effect more strongly on the shear loading. In case of bend type test, the adhesive bend strength in the smaller diameters (50 and $75\;{\mu}m$) widely vary, because the critical size of the natural defect (micro-crack) should vary more widely in the smaller diameters. In contrast, in case of shear type test, the adhesive shear strengths in each diameter of the columns little vary. This suggests that the size of the natural defects may not strongly influence on the adhesive shear strength. All the result suggests that both of the adhesive bend and shear strengths should be complicatedly affected by heat-treatment and the bonded columnar diameter.

• 대한치과의사협회지
• /
• 제53권3호
• /
• pp.178-186
• /
• 2015

Dental polymer-based luting materials are classified into esthetic resin cement, adhesive resin cement and self-adhesive resin cement. Due to the different component of each type of resin cement, the preconditioning method of tooth surface and the steps are different from each type of resin cement. The pre-treatment of adherend (ceramic, resin and metal) surface also varies with the type of resin cement and the manufacturer. In this study, the characteristics of each type of resin cement, mechanical properties, indication and advantages were investigated. Through these, clinical tips on using resin cements were suggested.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.140-141
• /
• 2017

This study is based on the evaluation of a single component injection type adhesive repair material and a new 2 component type used in leakage of underground concrete structures. The studies showed that based on different mix ratio of the 2 component type adhesive sealant comprised of an asphalt main and latex mixture agent the viscosity of the material compound differed significantly. Based on a permeability testing, injection and economic efficiency, and performance, the appropriate ratio was determined to be 6:1 and was proceeded to the KS F 4935 evaluation method. The 2 component type adhesive sealant uses a static mixer and a cartridge type container for the injection procedure and was able to satisfy the evaluation criteria outlined in the KS F 4935 standard.

• Journal of Welding and Joining
• /
• 제24권3호
• /
• pp.55-59
• /
• 2006

This paper is concerned with a study on cyclic bending load of bus folding door pillar including adhesive bonding and spot welding. Three specimen types were used such as spot welding, I-type adhesive bonding and M-type adhesive bonding in this study. The tensile-shear tests were carried out to evaluate the tensile-shear strength of these three specimen types. Also four-point bending tests were carried out to evaluate the static and dynamic bending load. From the results, using adhesive bonding has a better effect on the static and dynamic bending load than using spot welding. Therefore, manufacturing better structural products can be expected by applying hybrid welding using adhesive and spot welding to those.

• 한국산학기술학회논문지
• /
• 제12권1호
• /
• pp.559-564
• /
• 2011

PVC 기재에 자외선 차단제를 첨가하는 종래의 방법 대신, 점착제에 차단제를 혼합하여, 유리창에 부착하는 창문용 점착시트를 제조 하였다. 무기계차단제와 유기계차단제를 모두 사용 하였으며, 파장 280-400 nm 구간에서 흡광도를 측정하여 자외선 차폐성능을 평가하였다. 무기계보다는 유기계차단제의 성능이 우수하였으며, 1%만 첨가하여도 투명도나 점착력에는 영향을 주지 않고 대부분의 자외선을 차단하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.13-14
• /
• 2012

This study investigates the effect of adhesive type applying to surface-strengthening Ondol floor on level of attachment. Adhesive materials of four types produced in different companies were prepared and their attaching performance was examined. Test results showed that the water-based epoxy type produced in S company was the most effective on attaching the pieces of the surface-strengthening Ondol floor product.

• 폴리머
• /
• 제25권1호
• /
• pp.142-150
• /
• 2001

그 동안 고무산업 현장에서는 유기용제계 고무 접착제를 사용하여 왔으며 이로인해 품질의 불균일성과 화재위험성 및 인체유해성이 상존하여 왔다. 이를 해결하기 위해 비휘발성, 고인화점인 탄화수소계 원료를 사용하여 새로운 용액을 개발하였으며 이 용액은 인체에 대한 유해성이 매우 적으며 증발이 되지 않으므로 화재위험 및 환경적인 문제를 해결할 수 있었다. 새로운 용액은 기존 제품에 사용되어 온 고무계 binder대신 고무면으로 비휘발성 용제가 침투, 팽윤 현상을 일으켜 고무면 끼리 접착을 유도하는 새로운 개념의 제품이며 접착력 유지 시간이 기존 제품에 비해 현저히 개선되었다. 또한 내구력 면에서도 기존품과 비교할 때 유사한 양상을 보이므로 팽윤 현상으로 인한 물성저하가 나타나지 않았으며 각종 첨가제와도 반응성이 없는 안정한 제품이었다. 기존품의 경우 가교 후 절단면에서 가스로 인한 균열이 발생한 반면 새로운 제품의 경우는 이러한 현상이 발생하지 않았다.