• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.290-293
• /
• 2003

Ohmic contact characteristics of Al ion implanted n-type SiC wafer were investigated. Al ions implanted with high dose to obtain the final concentration of $5{\times}10^{19}/cm^3$, then annealed at high temperature. Firstly, B ion ion implanted p-well region were formed which is needed for fabrication of SiC devices such as DIMOSFET and un diode. Secondly, Al implanted high dose region for ohmic contact were formed. After ion implantation, the samples were annealed at high temperature up to $1600^{\circ}C\;and\;1700^{\circ}C$ for 30 min in order to activate the implanted ions electrically. Both the inear TLM and circular TLM method were used for characterization. Ni/Ti metal layer was used for contact metal which is widely used in fabrication of ohmic contacts for n-type SiC. The metal layer was deposited by using RF sputtering and rapid thermal annealed at $950^{\circ}C$ for 90sec. Good ohmic contact characteristics could be obtained regardless of measuring methods. The measured specific contact resistivity for the samples annealed at $1600^{\circ}C\;and\;1700^{\circ}C$ were $1.8{\times}10^{-3}{\Omega}cm^2$, $5.6{\times}10^{-5}{\Omega}cm^2$, respectively. Using the same metal and same process of the ohmic contacts in n-type SiC, it is found possible to make a good ohmic contacts to p-type SiC. It is very helpful for fabricating a integrated SiC devices. In addition, we obtained that the ratio of the electrically activated ions to the implanted Al ions were 10% and 60% for the samples annealed at $1600^{\circ}C\;and\;1700^{\circ}C$, respectively.

• Bulletin of the Korean Mathematical Society
• /
• v.47 no.6
• /
• pp.1163-1170
• /
• 2010

We study finite type curve in $R^3$(-3) which lies in a cylinder $N^2$(c). Baikousis and Blair proved that a Legendre curve in $R^3$(-3) of constant curvature lies in cylinder $N^2$(c) and is a 1-type curve, conversely, a 1-type Legendre curve is of constant curvature. In this paper, we will prove that a 1-type curve lying in a cylinder $N^2$(c) has a constant curvature. Furthermore we will prove that a curve in $R^3$(-3) which lies in a cylinder $N^2$(c) is finite type if and only if the curve is 1-type.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.11 no.6
• /
• pp.81-90
• /
• 2008

Recently, geofiber(polyester) reinforced soil was added on soil-seed mixture spray to control erosion and to improve vegetation growth on rocky slope sites. This research was conducted to compare vegetation effects and soil hardness on three types of soil-seed mixture spray on stone gabion river bank [A type : soil-seed mixture spray underlying 30cm thick sand with geofiber(geofiber reinforced soil system), B type : soil-seed mixture spray underlying 30cm thick sand without geofiber, C type : soil-seed mixture spray]. Evaluation were made concerning vegetation coverage, soil hardness and moisture content. The results of this study showed that A type system was effective for the growth of vegetation and soil hardness when compareed to B type and C type. A type and B type showed higher covering rate than C type on stone gabion river bank, and especially A type showed the highest covering rate. Soil hardness and water content were high on A type vegetation system compared to B type and C type. We noted that high soil hardness and high moisture content with geofiber(geofiber reinforced soil system) were effective both to control erosion from water current impact and to be high coverage and species of vegetation on stone gabion river bank.

• Textile Coloration and Finishing
• /
• v.12 no.1
• /
• pp.68-75
• /
• 2000

In this study, polyester DTY faille(yoryu) and N/NP microfiber fabrics were pretreated (desizing, scouring and shrinking) by Continuous Scouring and Shringking Equipment with rota-drum and conveyor type in which types were different with retaining method. The results were as follows. The shrinkage ratio of wp/wf direction of DTY fabrics scoured by conveyor type was 1.5/23% higher than those by rota-drum type at $97^\circ{C}$ with 10min. treatment. In this case, The shrinkage ratio of wp/wf direction by those types was about 15/27%, respectively. The shrinkage ratio of wp/wf direction of N/NP microfiber fabrics scoured by conveyor type was 1.5/23% higher than that by rota-drum type at $97^\circ{C}$ with 10min. treatment. The size add-on of DTY fabrics scoured at $97^\circ{C}$ with 10min. treatment by conveyor type and by rota-drum type were 0.15% and 0.42%, respectively. The size add-on of DTY fabric treated by rota-drum type decreased until 9min. of treated time, but increased after 9min. The size add-on of N/NP microfiber fabrics treated by conveyor type was decreased by increasing temperature and treated time, while the size add-on of that treated by rota-drum type was decreased until 6min. treated time and increased after 6min. The size add-on of N/NP microfiber fabrics treated by conveyor type at $97^\circ{C}$ for 10min. was 0.3% lower than that by rota-drum type.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.431-436
• /
• 2002

In this paper, to seek a solution of reducing autogenous shrinkage three types of bar restricted concrete specimens which have similar compressive strength were tested. The three type of concrete were plain concrete-P25 type, $10^{\circ}C$ fly-ash replaced concrete-F10 type, and $1^{\circ}C$ expansion admixture replaced concrete-SP1 type, and with the test result an experimental study was conducted to gain the tensile stress of concrete. From the result of P25, SP1, F10 tests, it was found that by the age of 14 the ratios of tensile stress to tensile strength of three specimens are $75^{\circ}C$, $47^{\circ}C$, $52^{\circ}C$ respectively. so we came to a conclusion that the SP1-type concrete has better capacity to reduce autogenous shrinkage than F10-type concrete at similar compressive strength condition.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2001.05a
• /
• pp.16-19
• /
• 2001

This paper presents a type-2 fuzzy C-means (FCM) algorithm that is an extension of the conventional fuzzy C-means algorithm. In our proposed method, the membership values for each pattern are extended as type-2 fuzzy memberships by assigning membership grades to the type-1 memberships. In doing so, cluster centers that are estimated by type-2 memberships may converge to a more desirable location than cluster centers obtained by a type-1 FCM method in the presence of noise.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.348-349
• /
• 2007

This paper describes the electrical characteristics of polycrystalline (poly) 3C-SiC thin film diodes, in which poly 3C-SiC thin films on n-type and p-type Si wafers, respectively, were deposited by APCVD using HMDS, Hz, and Ar gas at $1180^{\circ}C$ for 3 hr. The schottky diode with Au/poly 3C-SiC/Si(n-type) structure was fabricated. Its threshold voltage ($V_d$), breakdown voltage, thickness of depletion layer, and doping concentration ($N_D$) values were measured as 0.84 V, over 140 V, 61nm, and $2.7\;{\times}\;10^{19}\;cm^3$, respectively. The p-n junction diodes fabricated on the poly 3C-SiC/Si(p-type) were obtained like characteristics of single 3C-SiC p-n junction diodes. Therefore, poly 3C-SiC thin film diodes will be suitable microsensors in conjunction with Si fabrication technology.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.1041-1046
• /
• 1995

본 논문에서는 원전 I&C Function System Equipment (FSE)의 분류기준을 제시하기 위하여 IEEE 730.1, IEEE 828, IEEE 1012 및 IEC 1226의 관련 표준들을 비교 분석하여 I&C FSE를 근간으로 계측제어 소프트웨어를 원전 I&C 계통의 기능에 따라 Type I, Type II, Type III 및 Type IV로 분류할 수 있는 분류기준, 분류절차 및 예를 제시하였다. 또한, 본 논문의 분류기준을 토대로 하여 최근 이슈가 되고 있는 상용 소프트웨어 (Commercial Off The Shelf Software)의 원전 사용 승인기준을 제시하였다.

• Journal of Technologic Dentistry
• /
• v.23 no.2
• /
• pp.151-160
• /
• 2002

The purpose of this study was to evaluate the influence of sprue joint form on castability in dental prosthetics. The researcher carried out experimental study according to the type was divided by sprue joint form. Therefore type A was made thicken than sprue diameter of type B and type C was made it conversely. The results were as follows: 1. In the order of castability, type C(87.8%) was first and then type A(87.0%) and type B(79.2%) was last. However there was no significant difference statistically. 2. If reservior was located at the correct position and in sufficient size, internal shrinkage porosity in the casting bodies were not generated in the type of all. 3. At the reservoir, internal shrinkage porosity was generated first in type A, followed by type Band type C in the order named. Although it gives no impact on casting body, porosity seems to appear the least when it's produced in the form of type C.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.4
• /
• pp.465-474
• /
• 2015

Objective : A study and development of Korean Bobsleigh athletes's shoe which considers their physical condition has yet to be completed. So this study examines the effects of running shoes used by athletes based on plantar pressure and sprint time in order to provide raw data for the development of bobsleigh shoes suitable for Koreans. Method : The study selected seven bobsleigh athletes as subjects and selected three pairs of spiked running shoes from three companies, which will be referred to as Company N (Type A), Company A (Type B), and Company M (Type C). To analyze sprint time and plantar pressure for each shoe, the subject of the study were instructed to wear the selected shoes and to drag a sled at maximum sprint for 15 meters for 15 meters for in each condition that would be in real bobsleigh competitions. Results : The average sprint intervals for each athlete in each pair of shoes revealed Type C produce the fastest sprint in the order of Type C < Type A< Type B. Shoe Type C also had the largest contact area in order of Type C > Type B > Type A (p<.01). None of the three shoe types seem to yield a distinct advantage in terms of maximum average pressure or maximum pressure. Conclusion : In the future, functional analysis should be carried out by comparing the material properties, hardness, and toe spring of shoes based on the Type C shoe from Company M in order to develop bobsleigh shoes suitable for Koreans.