• Journal of the Korean Society of Clothing and Textiles
• /
• v.12 no.1 s.26
• /
• pp.45-52
• /
• 1988

To classify the foot type, direct measurements, metatarso-phalanx angle and foot print angle of the right and left foot were measured and analyzed. The results are as follows. 1. The correlation coefficients between right and left foot were high degree, and except medial malleous height, the diffences between right and left foot are not significant. 2. The correlation coefficient among direct measurements of the foot are high degree, tut the correlation coefficients between direct measurements and metatarso-phalanx angle and foot print angle are no or low degree. Therefore, to recognize the foot type, the direct measurements, metatarso-phalanx angle and foot print angle need to be measured independently. 3. According to foot width/foot $length{\times}100$ which is the slender degree of foot, three groups are distinguished: one is slender type of which foot width/foot $length{\times}100$ is less than $40.14\%$, two is standard type of which foot width/foot $length{\times}100$ is $40.14\%{\~}44.30\%$, three is broad type of which foot width/foot $length{\times}100$ is more than $44.30\%$. 4. On the photographs metatarso-phalanx angle was measured, and two groups are distinguished: one is normal type of which the metatarso-phalanx angle is more than $160^{\circ}$ and the other is the deformed type of which the metatarso-Phalanx angle is less than $159^{\circ}$. 5. By foot print angle $30^{\circ}$ which need reformation of the foot, two groups are distinguished: one is normal foot print angle of which the angle is more than $30^{\circ}$ and the other is flat foot print angle of which the angle is less than $30^{\circ}$. 6. Classifications by foot width/foot $length{\times}100$, metatarso-Phalanx angle and foot Print angle are put together, and then foot types are classified into 12 groups such as Table 11.

• The korean journal of orthodontics
• /
• v.22 no.4 s.39
• /
• pp.869-880
• /
• 1992

The purpose of this study was to evaluate the difference and relationship between the slope of articular eminence and the inclination of upper and lower incisor teeth, which are related to the functional stability of occlusion in mandibular protrusion, according to Ricketts' facial types, by the use of lateral cephalogram and SAM2 articulator in 68-adult normal occlusion without tooth missing, orthodontic treatment and occlusal equilibration. The results of this study were as follows : 1 . The angle of articular eminence slope to occlusal plane in brachyfacial type was steeper than that in dolichofacial type, but the angle of articular eminence slope to SN plane and FH plane was not different between facial types. 2. The upper incisor axis in dolichofacial type was steeper than that in brachyfacial type, but lingual surface slope of upper incisor was not different between facial types. 3. In all samples there was a positive correlation between the angle of articular eminence slope and the lingual surface slope of upper incisor to SN plane and FH plane, and in mesofacial type there was a positive correlation between the angle of articular eminence slope and the lingual surface slope of upper incisor to SN plane, FH plane and occlusal plane, and in brachyfacial type there was a positive correlation between the angle of articular eminence slope and the lingual surface slope of upper incisor to occlusal plane. 4. In all samples there was a positive correlation between the angle of articular eminence slope and the angle of Dc-Gn to SN plane, and in mesofacial type there was a positive correlation between the angle of articular eminence slope and the angle of Dc-Gn to occlusal plane, and in brachyfacial type there was a positive correlation between the angle of articular eminence slope and the angle of Dc-Gn to SN plane and FH plane. 5. In all samples there was a positive correlation between the angle of Dc-Gn and the lingual surface slope of upper incisor to SN plane and FH plane, and in mesofacial type there was a positive correlation between the angle of Dc-Gn and the lingual surface slope of upper incisor to SN plane. 6. In all samples and facial types there was a negative correlation between MP to 1 axis and condylar incisal angle.

• Korean Journal of Applied Biomechanics
• /
• v.26 no.3
• /
• pp.315-321
• /
• 2016

Objective: The aim of this study was to analyze effects of the toe-spring angle of bobsleigh shoes on start speed lap time to develop Korean-specific bobsled shoes suitable for winter environments and for domestic players on the basis of sports science and optimized biomechanical performance. Method: Seven Korean bobsleigh athletes participated in this study, with three pairs of sprint spikes from three companies (Type A, Type B, Type C). To analyze sprint lap time and forefoot bending angle for each shoe, participants were instructed to drag a sled 15 meters from the start line at a maximum sprint. forefoot bending angle was collected by a high speed camera, and lap time speed was measured. Results: Lap time for type B shoes was $3.52{\pm}0.17sec$, type A was $3.55{\pm}0.19sec$, and type C was $3.56{\pm}0.18sec$. Forefoot bending angles were: angle 1, $6.88{\pm}5.55^{\circ}$; angle 2, $9.23{\pm}6.38^{\circ}$; angle 3, $15.56{\pm}5.39^{\circ}$; angle 4, $9.54{\pm}3.85^{\circ}$; angle 5, $9.22{\pm}5.08^{\circ}$; angle 6, $7.66{\pm}6.44^{\circ}$; and angle 7, $4.30{\pm}6.24^{\circ}$ (p<.001). Forefoot bending in angle 3 was as follows: type A, $16.47{\pm}6.01^{\circ}$; type B, $14.30{\pm}4.96^{\circ}$; and type C, $15.90{\pm}5.17^{\circ}$. Conclusion: Hard outsoles and midsoles are better than soft type for reduced start lap time when developing a prototype Korean bobsled shoe.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.5
• /
• pp.827-833
• /
• 2022

In this study, the prediction of the bending angle for the 350 A bellows-type expansion joints and the structural stability according to the load were determined. The stability of the 2km piping system was predicted by applying the allowable bending angle of the expansion pipe joint obtained from the analysis. The maximum bending angle was calculated through bending analysis of the bellows-type expansion joints, and the maximum bending angle by numerical calculation was about 1.8°, and the maximum bending angle of the bellows obtained by comparing the allowable strength of the material was about 0. 22°. This angle was very stable compared to the allowable bending angle (3°) of the expansion pipe joint regulation. By applying the maximum bending angle, the allowable maximum deflection of the 2 km pipe was about 3.8 m. When the seismic load was considered using regression analysis, the maximum deflection of the 2km pipe was about 142.3mm, and it was confirmed that the bellows-type expansion joints and the deflection were stable compared to the allowable maximum deflection of the pipe system. These research results are expected to present design and analysis guidelines for the construction of piping and the development of bellows systems, and to be used as basic data for systematic research.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.381-386
• /
• 1999

In machining with cutting tool inserts having complex chip groove shape, the flow, curl and breaking patterns of the chip are different than in flat-face type inserts. In the present work, an effort is made to understand the three basic phenomena occurring in a chip since its formation in machining with groove type and pattern type inserts. These are the initial chip flow, the subsequent development of up and side curl and the final chip breaking due to the development of torsional and banding stresses. In this paper, chip flow angle in a groove type and pattern type inserts. The expression for chip flow angle in groove type and pattern type insets is also verified experimentally using high speed filming techniques.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.32 no.3
• /
• pp.207-217
• /
• 2010

The purpose of this study was to evaluate the effects of the stress distribution and displacement in mandible according to treatment modalities of mandibular angle fractures, using a three dimensional finite element analysis. A mechanical model of an edentulous mandible was generated from 3D scan. A 100-N axial load and four masticatory muscular supporting system were applied to this model. According to the number, location and materials of titanium and biodegradable polymer plates, the experimental groups were divided into five types. Type I had a single titanium plate in the superior border of mandibular angle, type II had two titanium plates in the superior tension border and in the inferior compression border of mandibular angle, type III had a single titanium plate in the ventral area of mandibular angle, type IV had a single biodegradable polymer plate in the superior border of mandibular angle, type V had a single biodegradable polymer plate in the ventral area of mandibular angle. The results obtained from this study were follows: 1. Stress was concentrated on the condylar neck of the fractured side except Type III. 2. The values of von-Mises stress of the screws were the highest in the just-posterior screw of the fracture line, and in the just-anterior screw of Type III. 3. The displacement of mandible in Type III was 0.04 mm, and in Type I, II, IV, and V were 0.10 mm. 4. The plates were the most stable in the ventral area of mandibular angle (Type III, V). In conclusion, the ventral area of mandibular angle is the most stable location in the fixation of mandibular angle fractures, and the just- posterior and/or the just-anterior screws of the fracture line must be longer than the other, and surgeons have to fix accurately these screws, and the biodegradable polymer plate also was suitable for the treatment of mandible angle fracture.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.2
• /
• pp.96-101
• /
• 2000

In machining with cutting tool inserts having complex chip groove shape the flow curl and breaking pattern of the chip are different than in flat-face inserts. In the present work an effort is made to understand the three basic phe-nomena occurring in a chip since its formation in machining with groove type and pattern type inserts. These are the ini-tial chip flow the subsequent development of up and side curl and the final chip breaking due to the development of tor-sional and bending stresses. in this paper chip flow angle in a groove type and pattern type inserts. The expres-sion for chip flow angle in groove type and pattern type inserts is also verified experimentally using high speed filming techniques.

• Journal of Technologic Dentistry
• /
• v.18 no.1
• /
• pp.117-127
• /
• 1996

This study was aimed to help the construction of esthetic dental prosthesis by investigation of the factors affecting on the atterition position and attrition angle of maxillary lateral incisors. Therefore 197 complete cast of maxillary and mandibualar extracted form the student of K. college were subjected for this study, and result throught the study are as follows. 1. None attrite rate of the maxiilary right lateral incisors was about 16.2% and that of the maxillary left lateral incisors was about 32.4% of examined teeth. 2. Throught mesiodistal attrition area 1) It showed that right lateral incisors was the most frequence in attrition of mesial area of incisal edge, and left lateral incisors was the most frequence in attrition of mesial and mid area of incisal edge. 2) It showed that square type arch was more frequence in attrition of all incisal edge, and ovoid type arch was more frequence in the attrition of mid area of incisal edge, and ovoid type arch was more frequence in the attrition of mid area of incisal edge, and taper type arch was more frequence in the attrition of mesial area of incisal edge than it of average frequence of right lateral incisors, by dental arch type. 3) It showed that square type arch was more frequence in the attrition of all area and mid area of incisal edge, and ovoid type arch was more frequence in the attrition of mid area of incisal edge, and taper type arch was more frequence in the attrition of mesial and distal area of incisal edge than it of average frequence of left lateral incisal, by dental arch type. 4) Sex, vertical overlap, horizontal overlap, incisal guide angle, did not affect significantly to throughout mesiodistal attrition, statistically 3. Throughout labiolingual attrition quantity. 1) It showed that throughout labiolingual attrition quantity was more attrition in order of taper type arch < ovoid type arch < square type arch, by dental arch type. 2) It showed that throughout labiolingual attrition qauntity was more attrition when the length of horizontal overlap is shorter than it of other, by horizontal overlap. 3) Throughout labiolingual attrition quantity of right lateral incisors showed that male was more attrition than it of female. 4) Vertical overlap, incisal guide angle, sex on left lateral incisors did not affect significantly to throughout labiolingual attrition, statistically. 4. Attrition angle 1) It showed that average attrition anlge of right lateral incisors were $30{\pm}13.02$ degree, and it of left lateral incisors were $26{\pm}13.37$ degree. 2) It showed that taper type arch have a bigger attrition angle than it of average of lateral incisors, and square tape arch have a smaller attrition angle than it of average of lateral incisors, by dental arch type. 3) It showed that horizontal overlap of 2.1mm above have a bigger attrition angle than it of average, by horizontal overlap. 4) It showed that female have a bigger attrition angle it of male, by sex.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2009.01a
• /
• pp.790-793
• /
• 2009

In the case of projection type display, it needs to use the screen in order to project the image clearly and wide viewing angle. We have been developing the step in type display system using the smoke screen. However, the image with smoke screen was flickered by gravity and air flow. Then we considered to reduce the flicker of the image and we found that flicker can be reduced and viewing angle becomes more large. This time we report the large viewing angle step in type display system using screen made up with very small particle size smoke and flow controlled nozzle. Hence, at first we considered the most suitable particle for the screen and then the shape of screen and then we constructed the array of flow controlled smoke screen. By the results of experiment we could get considerably high contrast flicker-less image and get the viewing angle more than $60^{\circ}$ by this flow controlled nozzle attached new type smoke screen and make clear the efficiency of this method.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.277-280
• /
• 2003

It was investigated that the "ㄱ" type angle product could be bended with a curvature during extrusion by extru-bending process. The bending process for the "ㄱ" type angle product can be developed by the hot metal extru-bending machine with the two punches moving in the different velocity. Because of non-symmetry of product, it is important to design the ruled surface contour of dies cavity for the welding and bending with two billets. So it is designed that the multi-hole container has two non-symmetric holes and non-symmetric contour of dies entrance. The results of the experiment show that "ㄱ" type angle product can be bended by the extrusion process and that the curvature of the product can be controlled by the velocity of punch and that the defects such as the distortion of section and the thickness change of the product and the folding and wrinkling of the product did not happen after the bending processing by the extrusion bending machine.