• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.753-760
• /
• 1999

Experiments were conducted to investigate the effect of the initial turbulent intensity on the flow and heat transfer characteristics for a two-dimensional impinging jet. A square rod was installed at the nozzle exit to increase initial turbulent intensity. A hot wire probe and thermochromic liquid crystal technique were used to measure the turbulent intensity and the surface temperature. All measurements were made over a range of nozzle-to-plate distance from 1 to 10 at Re=20,000. When the rod is not installed, the maximum stagnation point Nusselt number is occurred at H/B=9. A higher initial turbulent intensity enhanced the heat transfer on the surface. A correlation between stagnation point Nusselt number and turbulent intensity are presented.

• Bulletin of the Korean Chemical Society
• /
• 제24권3호
• /
• pp.357-362
• /
• 2003

The pathway producing imide ring closure during the thermal imidization of poly(amic acid) (PAA) was investigated in detail using a new analytical method, two-dimensional (2D) Raman correlation spectroscopy. The signs of the cross peaks in synchronous spectra provided evidence of the thermal imidization of PAA into PI as the heating temperature increased. The signs of the cross peaks in asynchronous spectra suggested that the imide-related modes changed prior to the amide or carboxylic mode, which indicates that cyclization occurred before the amide proton was abstracted.

• ETRI Journal
• /
• 제19권2호
• /
• pp.59-70
• /
• 1997

A study on the operation of a heat pipe with two heat sources has been performed to optimize the heat distribution of satellite equipment. A numerical modeling is used to predict the temperature profile for the heat pipe assuming cylindrical two-dimensional laminar flow for the vapor, and the conduction heat transfer for the wall and wick. An experimental study using the copper-water heat pipe with the length of 0.45 m has been performed to evaluate the numerical model and to compare the temperature distribution at the outer wall for the non-uniform heat distribution. The results on temperature profiles for the heat input range from 29 W to 47 W on each heater are presented. Also the correlation between the heat input and the temperature increase is presented for the optimum distribution on two heaters. The result shows that the outer wall temperature can be controlled by redistribution of heat sources. It is also concluded that the heat source closer to the condenser can carry more heat while maintaining lower temperatures at the outer wall.

• 자원리싸이클링
• /
• 제11권3호
• /
• pp.25-30
• /
• 2002

회전냉각기에서 일어나는 정상상태 열전달을 1차원으로 해석하였다 회전냉각기로 입력되고 배출되는 공기온도를 경계조건으로 삼았다. 경계 및 조업조건으로부터 2개의 상미분방정식과 2개의 대수방정식을 동시에 만족시키는 해를 계산하여 고체, 공기 벽의 온도분포를 구하였다. 본 연구에서 계산한 외벽온도는 실제 가동중인 회전냉각기에서 실측한 외벽온도와 서로 잘 일치하였다.

• 한국진공학회지
• /
• 제8권2호
• /
• pp.148-152
• /
• 1999

the low temperature magnetoresistance effect, electron mobilities, and 2 Dimensional electron Gases (2DEG) properties were investigated in $Si/Si_{1-x}Ge_x$ quantum well devices. N-type $Si/Si_{1-x}Ge_x$ structures were fabricated by utilizing a gas source Molecular Beam Epitaxy (GSMBE). Thermal oxidation was carried out in a dry O atmosphere at $700^{\circ}C$ for 7 hours. Electron mobilities were measured by using a Hall effect and a magnetoresistant effect at low temperatures down to 0.4K. Pronounced Shubnikov-de Haas (SdH) oscillations were observed at a low temperature showing two dimensional electron gases (2DEG) in s tensile strained Si quantum well. The electron sheet density (ns) of $1.5\times10^{12}[\textrm{cm}^{-2}]$ and corresponding electron mobility of 14200 $[\textrm{cm}^2V^{-1}s^{-1}]$ were obtained at a low temperature of 0.4K from $Si/Si_{1-x}Ge_x$ structures with thermally grown oxides.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제18권3호
• /
• pp.245-256
• /
• 2014

This work is focused on the boundary layer and heat transfer characteristics of hydromagnetic flow over a stretching sheet with variable thickness. Steady, two dimensional, nonlinear, laminar flow of an incompressible, viscous and electrically conducting fluid over a stretching sheet with variable thickness and power law velocity in the presence of variable magnetic field and variable temperature is considered. Governing equations of the problem are converted into ordinary differential equations utilizing similarity transformations. The resulting non-linear differential equations are solved numerically by utilizing Nachtsheim-Swigert shooting iterative scheme for satisfaction of asymptotic boundary conditions along with fourth order Runge-Kutta integration method. Numerical computations are carried out for various values of the physical parameters and the effects over the velocity and temperature are analyzed. Numerical values of dimensionless skin friction coefficient and non-dimensional rate of heat transfer are also obtained.

• 설비공학논문집
• /
• 제6권4호
• /
• pp.453-462
• /
• 1994

An unsteady quasi one-dimensional model of momentum, heat and mass transfer in a falling film of a vertical plate absorber which is cooled by air was developed using the integral method. Energy conservation of the absorber wall is considered in the model. The model can predict absorption rate, film thickness and mean velocity as well as concentration and temperature profiles. Predictions of steady state temperature and concentration profiles for LiBr/water system for constant wall temperature condition are in good agreement with the two-dimensional finite difference method solutions. Effects of operating conditions, such as convective heat transfer coefficient between the cooling air and the absorber wall, cooling air temperature and film thickness at inlet, on absorption rate of water vapor into LiBr/water solution were shown.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2334-2339
• /
• 2008

This paper proposes an improved mathematical model for predicting the frosting behavior on a two-dimensional fin considering the heat conduction of heat exchanger fins under frosting conditions. The model consists of laminar flow equation in airflow, diffusion equation of water vapor for frost layer, and heat conduction equation in fin, and these are coupled together. In this model, the change in three-dimensional airside airflow caused by frost growth is accounted for. The fin surface temperature increased toward the fin tip due to the fin heat conduction. On the contrary, the temperature gradient in the airflow direction(x-dir.) is small throughout the entire fin. The frost thickness in the direction perpendicular to airflow, i.e. z-dir., decreases exponentially toward the fin tip due to non-uniform temperature distribution. The rate of decrease of heat transfer in the airflow direction is high compared to that in the z-direction due to more decrease in the sensible and latent heat rate in x-direction.

• Nuclear Engineering and Technology
• /
• 제55권9호
• /
• pp.3320-3325
• /
• 2023

The scaled water-cooled Reactor Cavity Cooling System (RCCS) experimental facility reproduces a passive safety feature to be implemented in Generation IV nuclear reactors. It keeps the reactor cavity and other internal structures in operational conditions by removing heat leakage from the reactor pressure vessel. The present work uses Flownex one-dimensional thermal-fluid code to model the facility and predict the experimental thermal-hydraulic behavior. Two representative steady-state cases defined by the bulk volumetric flow rate are simulated (Re = 2,409 and Re = 11,524). Results of the cavity outlet temperature, risers' temperature profile, and volumetric flow split in the cooling panel are also compared with the experimental data and RELAP system code simulations. The comparisons are in reasonable agreement with the previous studies, demonstrating the ability of Flownex to simulate the RCCS behavior. It is found that the low Re case of 2,409, temperature and flow split are evenly distributed across the risers. On the contrary, there's an asymmetry trend in both temperature and flow split distributions for the high Re case of 11,524.

• Nuclear Engineering and Technology
• /
• 제54권10호
• /
• pp.3717-3723
• /
• 2022

For the first time, two-dimensional temporal behavior of the edge localized mode (ELM) filament is measured in the edge tokamak plasma with a multi-channel electrical probe array (MCEP). MCEP, which has 16 floating probes (4 × 4), is mounted at the far scrape-off layer (SOL) region in the KSTAR. An electron temperature and an ion flux are measured by sideband method (SBM), which can achieve two-dimensional measurements with high time resolution. Furthermore, temporal evolutions of the electron temperature and the ion flux are obtained during the ELM occurrence. In the H-mode period, short spikes from ELM bursts are observed in measured plasma parameters, and the trend is similar to that of typical Hα signal. Interestingly, when blob-like ELM filaments crash the probe, the heat flux is significantly higher in a local region of the probe array. The results show that our probe array using the SBM can measure the ELM behavior and the plasma parameters without the effect of the stray current caused by the huge device. This study can provide valuable data needed to understand the interaction between the SOL plasma and the plasma facing components (PFCs).