• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.10
• /
• pp.1003-1011
• /
• 2009

Transverse flux machine(TFM) has been developed to drive a machine of large input power at low-speed. However, it has complicated structure and large torque ripple due to its inherent structure. In this paper the characteristics of torque of a rotatory two-phase TFM are analyzed by using the 3-dimensional finite element method and optimal design. This research shows that one of the effective design variables is the skew angle of permanent magnet. The skew angles of permanent magnet are optimized by using a genetic algorithm. It also shows that the proposed optimal skew magnet not only increases average torque but also decreases torque ripple of a rotatory two-phase TFM.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.68 no.1
• /
• pp.36-43
• /
• 2019

In this paper, the characteristics of the coaxial magnetic gear according to the shape of the same gear ratio are analyzed using the two - dimensional finite element analysis. The rotor shape is SMCMG, CPCMG and RCMG. After this we analyzed the characteristics according to three shapes. Also, the amount of permanent magnet used in each shape was compared. Next, characteristics analysis of the magnetic gear according to the shape at the same torque was performed. And the total weight and efficiency of the magnetic gears were compared and verified.

• Proceedings of the KIEE Conference
• /
• 1997.07a
• /
• pp.47-50
• /
• 1997

The FEM(Finite Element Method) can be used to analysis SRM(Switched Reluctance Motor) as it can account for the salient pole geometry of the stator and rotor and the nonlinear properties of the magnetic materials. However, FEM requirers a lot of computer memory and computing time because, the kind of SRM drivers is verity and the switching strategies are various for one SRM driver. In this paper we proposed the method of analysis of a SRM which results are similar to FEM and has very short computing time. The Inductance and torque for each phase current at each rotor position are calculated by using two-dimensional nonlinear FEM analysis. Using the look-up table of inductance and torque and the voltage equations of SRM we obtained the phase current and torque. To verify proposed algorithm, 3 phase 6/4 SRM is analysed and found a good agreement with FEM results. And computing time is about 1/1600 of the FEM analysis.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2230-2235
• /
• 2011

The purpose of this paper is to provide the unbalanced magnetic force and vibration mode comparison between two large interior permanent magnet machines(IPM) with different pole-slot combination considering stator and rotor eccentricity. Due to the punching tolerance, the mixed eccentricity of air-gap is inevitable. It will generate the asymmetric magnetic flux density in air-gap, which makes the unbalanced magnetic pull and vibration. The study is focused on the unbalanced magnetic force and their harmonic components according to eccentricity conditions such as static, dynamic and mixed. When the high vibration is produced especially resonance, the obtained results provide clues what eccentricity condition occurs in the machine.

• 전기의세계
• /
• v.18 no.4
• /
• pp.7-15
• /
• 1969

In this method the condenser excite winding has the phase angle of 90 electrical degree, with the load winding in stator. The condenser excite wing is connected with the condenser while the load winding is with the full rectifer. Direct and quardrature axis components of rotating field winding are composed, of balanced two phase winding, and each one of them is connected with half wave rectifiers. Initically, small amount of lead current can be induced at the condenser excite winding by residual magnetism of rotor. The induced lead current forces the rotating field winding to be excited by synchronous alternating magnetic field. The speed electromotive force, there for, induced in rotating field winding shall electro magnetize the rotating field pole by rotating half wave rectifiers. In the case of the charging generator directly coupled with engines at the operation of wide range speed, the generated region, such as vehicles, aircraft, ships etc, is occured. In conclusion, we can take the advantage of, omitting of voltage regurator and current limiter for charging load and reducing the consumption of fuel using the generated region which can be devided in to Impossible generated region, Generated region, and suspension generated region.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.1
• /
• pp.40-44
• /
• 2013

This paper presents a design and characteristics analysis of novel 2-phase 4/3 switched reluctance motor (SRM) with short flux path for an air-blower application. The desired air-blower is unidirectional application, and requires a wide positive torque region without torque dead-zone. In order to get a wide positive torque region without torque dead-zone during phase commutation, asymmetric inductance characteristic with non-uniform air-gap is considered. The proposed motor could be started at any rotor position with high efficiency drive. The proposed 2-phase 4/3 SRM is verified by finite element method analysis.

• Journal of KSNVE
• /
• v.9 no.3
• /
• pp.570-576
• /
• 1999

This paper presents numerical and experimental results of modal parameter identification in a generator stator frame for 500 MW fossil power plants. A commercial finite element analysis S/W was employed for modal analysis. The generator is excited by alternating electromagnetic forces, mainly of 120 Hz in 60 Hz machines, due to magnetic field and electric current in windings. It is necessary to verify that the stator frame has adequate frequency margin from the excitation frequency to avoid possible resonance when operating. Thus, frequency margin required for the stator frame is established using the numerical and experimental results. The results show that the stator frame meets the frequency-margin requirements. Also, results of modal analysis for design modification in order to reduce weights of the stator frame without deteriorating vibration characteristics are presented.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.10
• /
• pp.959-967
• /
• 2012

The theory for a new electromagnetically biased diskless combined radial and axial magnetic bearing is developed. A typical magnetic bearing system is composed of two radial magnetic bearings and an axial magnetic bearing. The axial magnetic bearing with a large axial disk usually limits rotor dynamic performance and makes assembling and disassembling difficult for maintenance work. This paper proposes a novel electromagnet biased integrated radial-axial magnetic bearing without axial disk. This integrated magnetic bearing uses two axial coils to provide the bias flux to the radial and axial air gaps of the combined bearing. The axial magnetic bearing unit in this combined magnetic bearing utilizes reluctance forces developed in the non-uniform air gaps such that the axial disk can be removed from the bearing unit. The 4-pole homopolar type radial magnetic bearing unit is also designed and analyzed. Three dimensional finite element model for the bearing is also developed and analyzed to illustrate the diskless combined magnetic bearing.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.822-827
• /
• 2013

In this paper, how to stop a moment to experiment with stop function, electric brake type scale model propulsion system is designed and fabricated by control of the braking torque is proposed. Scale model system for motor-driven, inertial load, the structure of the load for the motor and the inverter system was constructed with two sets of converters, the actual range of the rotational speed of the vehicle DDM experiments to be able to. In Additional, observer to estimate the rotor position and speed of using resolver, and the pole at low speed, speed detection methods have been developed. As a result of this study, first, stop the moment Second, the reduction of braking torque, and how to initiate the operation of the air brake blending by using the braking, improve braking methods that only use the electric brake to stop brought.

• Journal of Power Electronics
• /
• v.11 no.1
• /
• pp.37-44
• /
• 2011

In this paper, a four-phase 8/6-pole 4-kW SR motor drive model is presented. Based on experimental data, the model allows an accurate simulation of a drive in dynamic operation. Simulations are performed and a laboratory type set-up is built based on a TI TMS320F2812 platform to experimentally verify the theoretical results obtained for a SR motor. To reduce acoustic noise and to correct the power factor of this drive, a two-stage power converter is proposed that uses a current source rectifier (CSR) as the input stage for the asymmetrical converter of the studied SRM. Employing the space-vector modulation (SVM) method in matrix converters, the CSR switching allows the dc link's capacitors to be eliminated and the power factor of the SRM drive to be improved. As the electrical motive force (emf) is directly proportional to the rotor speed, the input voltage to the machine can be programmed to be a function of the speed with the modulation index of the CSR, leading to a reduction in the acoustic noise of the SRM drive. Simulation of the whole SRM drive system is performed using MATLAB-Simulink. The results fully comply with the required conditions such as power factor correction with an improvement in the THD.