• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.30 no.3
• /
• pp.325-336
• /
• 2020

Nonlinear Invariant Attack is an attack that should be considered when constructing lightweight block ciphers with relatively simple key schedule. A shortcut to prove a block cipher's resistance against nonlinear invariant attack is checking the smallest dimension of linear layer-invariant linear subspace which contains all known differences between round keys is equal to the block size. In this paper, we presents the following results. We identify the structure and number of optimal bit-permutations which require only one known difference between round keys for a designer to show that the corresponding block cipher is resistant against nonlinear invariant attack. Moreover, we show that PRESENT-like block ciphers need at least two known differences between round keys by checking all PRESENT-like bit-permutations. Additionally, we verify that the variants of PRESENT-like bit-permutations requiring the only two known differences between round keys do not conflict with the resistance against differential attack by comparing the best differential trails. Finally, through the distribution of the invariant factors of all bit-permutations that maintain BOGI logic with GIFT S-box, GIFT-variant block ciphers require at least 8 known differences between round keys for the resistance.

• Restorative Dentistry and Endodontics
• /
• v.28 no.5
• /
• pp.378-384
• /
• 2003

This study evaluated the influence of a desensitizer(MS coat) on microtensile bond strength of different adhesives:a three-step adhesive(All-Bond 2), a two-step adhesive(Single Bond), a one-step adhesive(One-up Bond F). Non-caries extracted human molars were used. Dentin surface was obtained by horizontal section on mid-portion of crown using a water-cooled low speed diamond saw. Teeth were randomly divided into 6 group. AMO(MS coat + All Bond), SMO(MS coat + Single Bond)- and OMO(MS coat + One-up Bond F)-dentin surface were treated with 17% EDTA before bonded adhesive. AMX-, SMX- and OMX-dentin surface were bonded with All-Bond 2, Single Bond and One-up Bond F, respectively. with no previous treatment with MS coat and 17% EDTA. About 1cm high resin composite($Z-250^{TM}$) were incrementally build-up on the treated surface. The specimens for the microtensile test were serially sectioned perpendicular to the adhesive layer to obtain $0.7{\times}0.7mm$ sticks. 30 sticks were prepared from each group. After that. tensile bond strength for each stick was measured with Microtensile Tester at a 1mm/min crosshead speed. Fractured dentin surfaces were observed under the SEM. The results were statistically analysed by using a One-way ANOVA and Tukey's test(p<0.05). Value in MPa were: $AMO-44.35{\pm}13.21;{\;}SMO-39.35{\pm}13.32;{\;}OMO-31.07{\pm}10.25;{\;}AMX-49.22{\pm}16.38;{\;}SMX-56.02{\pm}13.35;{\;}OMX-72.93{\pm}16.19$. Application of MS coat reduced microtensile bond strengths of both Single Bond and One-up Bond F, whereas microtensile bond strengths of All-Bond 2 were not affected significantly.

• Restorative Dentistry and Endodontics
• /
• v.35 no.5
• /
• pp.321-334
• /
• 2010

Objectives: The purpose of this study is to evaluate bonding efficacy by means of measuring the effect of remained solvent on Degree of conversion(DC) and ${\mu}TBS$ and FE-SEM examination. Materials and Methods: Two 2-step total etching adhesives and two single-step self etching adhesives were used in this study. First, volume weight loss of 4 dentin adhesives were measured using weighting machine in process of time in normal conditions and calculate degree of evaporation (DE). Reaction/reference intensity ratio were measured using micro-Raman spectroscopy and calculate DC according to DE. Then 2 experimental groups were prepared according to air-drying methods (under, over) and control group was prepared to manufacturer's instruction. Total 12 groups were evaluated by means of micro tensile bond strength and FE-SEM examination. Results: Degree of evaporation (DE) was increased as time elapsed but different features were observed according to the kind of solvents. Acetone based adhesive showed higher DE than ethanol and butanol based adhesive. Degree of conversion (DC) was increased according to DE except for $S^3$ bond. In ${\mu}TBS$ evaluation, bond strength was increased by additional air-drying. Large gaps and droplets were observed in acetone based adhesives by FE-SEM pictures. Conclusions: Additional air-drying is recommended for single-step self etching adhesive but careful consideration is required for 2-step total etching adhesive because of oxygen inhibition layer. Evaporation method is carefully chose and applied according to the solvent type.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.4
• /
• pp.9-17
• /
• 2013

This paper describes an experimental program to investigate the shear behavior of insulated concrete sandwich panels (CSPs) with different types of GFRP shear connector. The study included testing of 13 insulated CSP specimens with two types of surface conditions for extruded polystyrene (XPS) insulation and various shapes of shear connectors. All specimens were loaded in direct shear by means of push-out and were consist of three concrete panels, two insulation layer and four rows of GFRP shear connectors. Load-relative slip between concrete panel and insulation response of CSP specimens has been established through push-out shear test. Test results indicate that the surface condition of insulation has a significant effect on the bond strength between concrete panel and insulation. The specimen used XPS foam with 10mm deep slot shows higher bond strength than those used XPS foam with meshed surface. Corrugated GFRP shear connectors show equivalent strength to grid GFRP shear connectors. Cross-sectional area and embedded length of shear connector have a notable effect on overall response and inplane shear strength of the CSP specimens.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.4
• /
• pp.54-61
• /
• 2005

An aquifer thermal energy storage (ATES) system can be very cost-effective and renewable energy sources, depending on site-specific parameters and load characteristics. In order to develop the ATES system which has certain hydrogeological characteristics, understanding the thermohydraulic process of an aquifer is necessary for a proper design of an aquifer heat storage system under given conditions. The thermohydraulic transfer for heat storage was simulated according to two sets of simple pumping and waste water reinjection scenarios of groundwater heat pump system operation in a two-layered aquifer model. In the first set of the scenarios, the movement of the thermal front and groundwater level was simulated by changing the locations of injection and pumping wells in a seasonal cycle. However, in the second set the simulation was performed in the state of fixing the locations of pumping and injection wells. After 365 days simulation period, the shape of temperature distribution was highly dependent on the injected water temperature and the distance from the injection well. A small temperature change appeared on the surface compared to other simulated temperature distributions of 30 and 50 m depths. The porosity and groundwater flow characteristics of each layer sensitively affected the heat transfer. The groundwater levels and temperature changes in injection and pumping wells were monitored and the thermal interference between the wells was analyzed to test the effectiveness of the heat pump operation method applied.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.406-406
• /
• 2010

일반적으로, 나노스케일의 MOS 소자에서는 게이트 절연체 두께가 감소함에 따라 tunneling effect의 증가로 인해 PID (plasma induced damage)로 인한 소자 특성 저하 현상을 감소하는 추세로 알려져 있다. 하지만 요즘 많이 사용되고 있는 high-k 게이트 절연체의 경우에는 오히려 더 많은 charge들이 trapping 되면서 PID가 오히려 더 심각해지는 현상이 나타나고 있다. 이러한 high-k 게이트 식각 시 현재는 주로 Hf-based wet etch나 dry etch가 사용되고 있지만 gate edge 영역에서 high-k 게이트 절연체의 undercut 현상이나 PID에 의한 소자특성 저하가 보고되고 있다. 본 연구에서는 이에 차세대 MOS 소자의 gate stack 구조중 issue화 되고 있는 metal gate 층과 gate dielectric 층의 식각공정에 각각 중성빔 식각과 중성빔 원자층 식각을 적용하여 전기적 손상 없이 원자레벨의 정확한 식각 조절을 해줄 수 있는 새로운 two step 식각 공정에 대한 연구를 진행하였다. 먼저 TiN metal gate 층의 식각을 위해 HBr과 $Cl_2$ 혼합가스를 사용한 중성빔 식각기술을 적용하여 100 eV 이하의 에너지 조건에서 하부층인 $HfO_2$와 거의 무한대의 식각 선택비를 얻었다. 하지만 100 eV 조건에서는 낮은 에너지에 의한 빔 스케터링으로 실제 패턴 식각시 etch foot이 발생되는 현상이 관찰되었으며, 이를 해결하기 위하여 먼저 높은 에너지로 식각을 진행하고 $HfO_2$와의 계면 근처에서 100 eV로 식각을 해주는 two step 방법을 사용하였다. 그 결과 anistropic 하고 하부층에 etch stop된 식각 형상을 관찰할 수 있었다. 다음으로 3.5nm의 매우 얇은 $HfO_2$ gate dielectric 층의 정확한 식각 깊이 조절을 위해 $BCl_3$와 Ar 가스를 이용한 중성빔 원자층 식각기술을 적용하여 $1.2\;{\AA}$/cycle의 단일막 식각 조건을 확립하고 약 30 cycle 공정시 3.5nm 두께의 $HfO_2$ 층이 완벽히 제거됨을 관찰할 수 있었다. 뿐만 아니라, vertical 한 식각 형상 및 향상된 표면 roughness를 transmission electron microscope(TEM)과 atomic force microscope (AFM)으로 관찰할 수 있었다. 이러한 중성빔 식각과 중성빔 원자층 식각기술이 결합된 새로운 gate recess 공정을 실제 MOSFET 소자에 적용하여 기존 식각 방법으로 제작된 소자 결과를 비교해 본 결과 gate leakage current가 약 one order 정도 개선되었음을 확인할 수 있었다.

• Journal of KIISE:Computing Practices and Letters
• /
• v.15 no.11
• /
• pp.846-850
• /
• 2009

Recently, wireless sensor networks have found their way into a wide variety of applications and systems with vastly varying requirements and characteristics such as environmental monitoring, smart spaces, medical applications, and precision agriculture. The sensor nodes are battery powered. Therefore, the energy is the most precious resource of a wireless sensor network since periodically replacing the battery of the nodes in large scale deployments is infeasible. Energy efficient mechanisms for gathering sensor readings are indispensable to prolong the lifetime of a sensor network as long as possible. There are two energy-efficient approaches to prolong the network lifetime in sensor networks. One is the compression scheme to reduce the size of sensor readings. When the communication conflict is occurred between two sensor nodes, the sender must try to retransmit its reading. The other is the MAC protocol to prevent the communication conflict. In this paper, we propose a novel approaches to reduce the size of the sensor readings in the MAC layer. The proposed scheme compresses sensor readings by allocating the time slots of the TDMA schedule to them dynamically. We also present a mathematical model to predict latency from collecting the sensor readings as the compression ratio is changed. In the simulation result, our proposed scheme reduces the communication cost by about 52% over the existing scheme.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.459-463
• /
• 2017

Hot dip galvanizing in the steel plant is one of the most widely used methods for preventing the corrosion of steel materials including structures, steel sheets, and materials for industrial facilities. While hot dip galvanizing has the advantage of stability and economic feasibility, it has difficulty in repairing equipment and maintaining the facilities due to high-temperature oxidation caused by Zn Fume where molten zinc used in the open spaces. Currently, SM45C (carbon steel plate for mechanical structure, KS standard) is used for the equipment. If a part of the equipment is resistant to high temperature and Zn fume, it is expected to improve equipment life and performance. In this study, the manufactured Ni alloy was tested for its corrosion resistance against Zn fume when it was used in the hot dip galvanizing equipment in the steel plant. Two kinds of materials currently used in the equipment, new Ni alloy and Inconel(typical corrosion-resistant Ni alloy), were selected as the reference groups. Two kinds of molten metal were used to confirm the corrosion of each alloy according to the molten metal. Zn fume was generated by bubbling Ar gas from molten Zn in a furnace($500{\sim}700^{\circ}C$) and the samples were analyzed after 30 days. After 30 days, the specimens were taken out, the oxide layer on the surface was confirmed with an optical microscope and SEM, and the corrosion was confirmed using a potentiodynamic polarization test. Corrosion depends on the type of molten metal.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.4
• /
• pp.954-961
• /
• 2017

We investigated the purifications of PE-gal and CPN-gal, synthesized by transgalactosylation reaction using recombinant ${\beta}$-gal. The reaction mixture containing PE and PE-gal was first mixed with EA, and thereafter PE and PE-gal were distributed in two-phase (EA/water) system. In this system, PE and PE-gal was selectively moved into EA and water phase, respectively. Then, the water phase was collected, and silica gel chromatography was carried out using the collected water phase. Finally, we compared two purified PE-gal samples using HPLC and TLC analysis, in which the one was purified only by silica gel chromatography and the other was purified by EA extraction followed by silica gel chromatography. In the latter case, the residual PE was almost completely removed, whereas, in the former case, the residual PE was remained remarkably. Additionally, the purification yield of PE-gal was about 21% on the basis of mole. In the same purification protocol, CPN-gal was able to be purified using EA extraction followed by silica gel chromatography, in which the residual CPN was almost removed when CPN-gal was purified by EA extraction followed by silica gel chromatography.

• Cross-Cultural Studies
• /
• v.19
• /
• pp.39-77
• /
• 2010

The cinema of Peter Greenaway has consistently engaged questions of the relationship between the arts and particularly the relations of image and writing to cinema. When different types of images are correlated and merged with each other on the borders of painting, photography, film, video and computer animation, the interrelationships of the distinct elements cause a shift in the notion of the whole image. This analysis proposes to articulate the complex relationship between the 'interartial' dimension and the 'intermedial' dimension in Peter Greenaway's film, (1991). If the interartiality is interested in the interaction between various arts, including the transition from one to another, the intermediality articulates the same type of relationship between two or more media. The interactional relationship is the same on both sides; on the contrary, the relationship between art and media does not show the same symmetry. All art is based on one or more media - the media is a condition existence of art - but no art can't be reduced to the status of media. This suggests that if the interartiality always involves the intermediality, this proposal may not be reversed. First, we analyse a self-conscious investigation into digital art and technology. Prosospero's Books can be read as a daring visual essay that self-consciously investigates the technical and philosophical functions of letters, books, images, animated paintings, digital arts, and the other magical illusions, which have been modern or will be post-modern media to represent the world. Greenaway uses both conventional film techniques and the resources of high-definition television to layer image upon image, superimposing a second or third frame within his frame. Greenaway uses the frame-within-frame as the cinematic equivalent of Shakespeare's paly-within-play : it offer him the possibility to analyse the work of art/artist/spectator relationship. Secondly, we analyse the relationship between the written word, oral word and the books. Like the written word, the oral word changes into a visual image: The linguistic richness and nuances of Shakeaspeare's characters turn into the powerful and authoritative, but monotone, voices of Gielgud-Prospero, who speaks the Shakespearean lines aloud, shaping the characters so powerfully through his worlds that they are conjured before us. Specially each book is placed over the frame of the play's action, only partially covering the image, so that it gives virtually every frame at least two space-time orientations. Thirdly, we try to show how Peter Greenaway uses pictorial references in order to illustrate the context of the Renaissance as well as pictorial techniques and language in order to question the nature of artistic representation. For exemple, The storm is visualised through reference to Botticelli's : the storm of papers swirling around the library is constructed to look like a facsimili copy of Michelangelo's Laurentiana Library in Florence. Greenaway's modern mannerism consists in imposing his own aesthetic vision and his questioning of art beyond the play's meta-theatricality: in other words, Shakespeare''s text has been adapted without being betrayed.