• Journal of Power System Engineering
• /
• v.11 no.1
• /
• pp.98-106
• /
• 2007

This paper presents a statistical prediction procedure for the propeller racing of ships with twin screw propellers sailing in ocean waves. The propeller racing is one of the most important factors of seakeeping qualities in relation to the safety of main engine and shafting system. It is especially significant key word for designing the twin-screw-propeller-type ship in view of allowable maximum propeller diameter etc.. In former studies, the propeller racing generally means the situation (propeller exposed) in which the relative motion amplitude between ship hull and wave surface would exceed a depth of point in rotary disk propeller. Therefore, it seems that the magnitude of the amplitude and its exceeding frequency have been examined as a principal subject of study as usual. However, the time during which the amplitude exceeds a depth of point must be also one of most important factor affecting the trend of propeller racing. This paper proposes a simply practical method for estimating the time lasting of exposed propeller related to twin screw propeller racing in rough confused seas on the basis of the statistics. Then, it is confirmed that the practical method is useful and convenience for considering the propeller racing in the stage of the basic design.

• Proceedings of KOSOMES biannual meeting
• /
• 2018.06a
• /
• pp.72-72
• /
• 2018

• Journal of Ocean Engineering and Technology
• /
• v.27 no.6
• /
• pp.56-64
• /
• 2013

Crabbing motion is the pure sway motion of a ship without surge velocity. Thus, it can be applied to a berthing operation. Crabbing motion is induced by a peculiar operation method called the push-pull mode. The push-pull mode is induced by using a combination of the main propeller and side thruster. Two propellers generating the same amounts of thrust and rotating in opposite directions produce some yawing moment on a vessel but do not induce longitudinal motion. With the additional operation of side thrusters, the push-pull mode is used to induce a large amount of lateral force. In this paper, three-degree-of-freedom equations of motion such as for the surge, sway, and yaw are constructed for the crabbing motion. Based on these equations of motion, a feedback linearization control method is applied to auto-berthing control for a twin-screw ship with side thrusters. The controller can deal with the nonlinearity of a system, which is present in the berthing maneuver of a twin screw ship. A simulation of the auto-berthing of a ship is performed to validate the performance of the designed controller.

• Journal of the Korean Institute of Navigation
• /
• v.25 no.4
• /
• pp.443-453
• /
• 2001

선박조종시뮬레이터는 해기사의 교육 훈련, 항만 수로 설계 시 안전성 평가, 선박설계시 조종성능의 검토등으로 널리 활용되고 있다. 본 논문은 최근 한국해양대학교에서 개발한 선박조종시뮬레이터를 소개하고 개발 과정과 활용에 대하여 논의한다. 본 시뮬레이터는 Operation Panel, Instructor's Console, Ship Dynamics Calculation, 3D Bridge View, 2D Bird's Eye View 및 Navigational Indicators의 6구성요소로 이루어져 있으며, 이를 위해 8대의 퍼스널 컴퓨터가 배치되어 있다. 모든 구성요소들은 효율적인 정보 교환을 위하여 분산처리네트워크 방식으로 연결되어 있다. 또한, 본 논문은 항만내에서의 저속 시 조종운동 수학모델과 가상현실 모델링에 대해서도 논의한다. 마지막으로, 부산항에 대한 2축2타선박의 접안 조종 시뮬레이션 예를 보여주고 있다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.57-64
• /
• 2021

Maneuvering motions of a ship in calm water are studied through the concept of MMG model. Governing forces are defined by the use of available empirical formulae that require only main ship particulars as input variables. In order to validate the calculation tool, a full-scale sea experiment was carried out in Osaka Bay using a 17-m twin-screw passenger ferry. Test execution and data measurement were performed through the utilization of an autopilot control unit and satellite compass. The result of a straight running test confirms the acceptable accuracy in addressing the surge motion problem. Reasonable agreement between simulation and experiment is also confirmed for 5°/5° and 10°/10° zig-zag tests despite the strong environmental disturbance. The current model can generally represent the subject ship maneuvering motions and is promising for the application to other ship hulls.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.8 no.1
• /
• pp.81-87
• /
• 2002

High speed naval ships are configured with open shafts The shafts, bearings, and propellers are supported by shaft struts. Proper design of struts involves issues of structural, vibration, and hydrodynamic analysis and design. Strut arm cavitation in high speed occurs because of a misalignment of the strut arm with the local incident flow. Proper selection of the strut section can minimize the generation of cavitation. This paper describes issues in the design struts and notices based on the design of Patrol Craft and Amphibious Ship.

• Journal of Ocean Engineering and Technology
• /
• v.36 no.2
• /
• pp.91-100
• /
• 2022

In general, the effect of roll motion is not considered in the study on maneuverability in calm water. However, for high-speed twin-screw ships such as the DTMB 5415, the coupling effects of roll and other motions should be considered. Therefore, in this study, the estimation of maneuverability using a 4-degree-of-freedom (DOF; surge, sway, roll, yaw) maneuvering mathematical group (MMG) model was conducted for the DTMB 5415, to improve the estimation accuracy of its maneuverability. Furthermore, a study on the change in turning performance according to the fin angle was conducted. To accurately calculate the lift and drag forces generated by the fins, it is necessary to consider the three-dimensional shape of the wing, submerged depth, and effect of interference with the hull. First, a maneuvering simulation model was developed based on the 4-DOF MMG mathematical model, and the lift force and moment generated by the side fins were considered as external force terms. By employing the CFD model, the lift and drag forces generated from the side fins during ship operation were calculated, and the results were adopted as the external force terms of the 4-DOF MMG mathematical model. A 35° turning simulation was conducted by altering the ship's speed and the angle of the side fins. Accordingly, it was confirmed that the MMG simulation model constructed with the lift force of the fins calculated through CFD can sufficiently estimate maneuverability. It was confirmed that the heel angle changes according to the fin angle during steady turning, and the turning performance changes accordingly. In addition, it was verified that the turning performance could be improved by increasing the heel angle in the outward turning direction using the side fin, and that the sway speed of the ship during turning can affect the turning performance. Hence, it is considered necessary to study the effect of the sway speed on the turning performance of a ship during turning.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.1
• /
• pp.34-46
• /
• 2019

This paper provides the numerical results for the self-propulsion performance in waves of a car ferry vessel with damage in one of its twin-screw propulsion systems without flooding the engine room. The numerical simulations were carried out according to the Safe Return to Port (SRtP) regulation made by the Lloyd's register, where the regulation requires that damaged passenger ships should have an ability to return to port with a speed of 6 knots in a Beaufort 8 sea condition. For the validation of the present numerical analysis study, the resistance performance and the self-propulsion performance of the car ferry in intact and damaged conditions in calm water were calculated, which showed a satisfactory agreement with the model test results of Korea Research Institute of Ship and Ocean engineering (KRISO). Finally, the numerical simulation of self-propulsion performance in waves of the damaged car ferry ship was carried out for a normal sea state and for a Beaufort 8 sea state, respectively. The estimated average Brake Horse Power (BHP) for keeping the damaged car ferry ship advancing at a speed of 6 knots in a Beaufort 8 sea state reached about 47% of BHP at MCR condition or about 56% of BHP at NCR condition of the engine determined at the design state. In conclusion, it can be noted that the engine power of the damaged car ferry ship in single propulsion condition is sufficient to satisfy the SRtP requirement.