• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.673-674
• /
• 2010

• Journal of ILASS-Korea
• /
• v.8 no.3
• /
• pp.1-9
• /
• 2003

The objective of this study is to compare atomization characteristics for differently made an ultrasonic twin-fluid nozzle. A spray system, an ultrasonic system, and three different type(Nozzle type, Tube type. Conventional type)are made and compared experimental and numerical results. In this investigation, the measurement and numerical analysis of spray droplet are to analyze the effects of ultrasonic energy on the agricultural atomization spray system in order to protection of dispersion droplets. It is clarified that ultrasonic energy forcing into a nozzle is valid to obtain atomization enchancement. As the result of comparing the experimental and numerical result, it is confirmed that nozzle type is highest efficiency than that of tube type and conventional type, also well fit, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.1
• /
• pp.132-139
• /
• 1997

Spray characteristics of external mixing sonic twin-fluid atomization nozzles are investigated experimentally. Particle sizes are measured by the Fraunhofer diffraction method using the Malvern particle analyzer, and their radial distributions are obtained using the tomographical transformation technique. The spatial distribution of SMD shows that the drop size increases in the radial direction at a fixed liquid flow rate, and the distribution is getting uniform rapidly as the atomizing gas pressure increases. The SMD decreases as the liquid flow rate increases at a fixed GLR. It is found that the atomization efficiency of the flush type sonic nozzle is superior to that of protrusion type. The effect of laser beam diameter of the particle analyzer on the spatial SMD distribution is minor at present experimental conditions.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.758-763
• /
• 2001

This paper presents twin spray characteristics of two impinging F-O-O-F type injectors in which fuel and oxidizer impinge on each other to atomize under the various conditions. The droplet size and velocity in the impinging spray flow field were measured using a PDPA. The droplet size and velocity were investigated at mixture ratios of 1.5, 2.0, 2.47 and 3.0 for four injectors in which two single F-O-O-F injectors were arranged at intervals of 20.8, 31.2, 41.6 and 62.4mm respectively. In general, the arithmetic mean diameter, SMD and standard deviation of droplet size in the interaction area (X=0 and Y=0mm) were smaller. The axial velocity in the interaction area was slightly higher. Considering the behavior of impinged droplets using the We number calculated by using the axial velocity instead of the relative velocity in line C in Fig. 1(b) for four injectors, it is consumed that the We number over 500 had the possibility to disintegrate, and the We number below 500 had it to cohere after impingement of twin spray. The results of this study can be used for the design of a nozzle for liquid propellant rockets.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.980-987
• /
• 2006

Recently, twin-tunnel is often designed considering the aspects of disaster prevention and economic reasons. However, the design cases and the studies are relatively insufficient. By the twin-tunnel excavation, deviate stresses of pillar between tunnels are increased and the increased stresses induce the instability of the twin-tunnel. In this study, numerical analyses about the twin-tunnel behaviour are conducted while varying ground strength, width of pillar and depth of earth cover and a series of regression analyses are carried out by using the results of numerical analyses for the twin-tunnel. Based on the numerical analyses, an estimation method of derived stresses is suggested though the regression analyses. Also, based on the results of regression analyses, an quantitative estimation method considering the reinforcement effects is also suggested. Then various parametric studies are conducted to be considered the reinforcement type and various design parameters. Finally, the efficiency of the suggested method is verified through the results of parametric studies.

• Journal of Ginseng Research
• /
• v.4 no.1
• /
• pp.65-71
• /
• 1980

Twin-bud seedlings and four-leaflet seedlings of ginseng were found and transplanted to field and their growth characteristics were investigated. 1. Appearance frequencies of twin-bud and four-leaflet seedlings were 0.3 and 0.4 percent, respectively, in common nursery bed: and were 6.6 and 28.4 percent, respectively, in polystem line. 2. Generally, the growth of twin.bud and four-leaflet seedlings were better than those of common seedlings both in aerial part and in root. Root weights of both type seedlings exceeded the common ones by 66 and 38 percent, respectively. 3. When they became two-year-old plants, leafiet number of common plant was 11.6, and those of twin-bud and four-leaflet-seedling plants were 18.1 and 13.8, respectively. There were no inflorescence in twin-bud-seedling plant, but the ratios of in florescent Plant in four-leaflet.seedling and common plant were 44.0 and 12.5 percent, respectively. 4. In two-year-old plant, root weights of twin-bud and four-leaflet-seedling plants were heavier than those of common ones by 27 and 20 percent, respectively.

• Journal of Korea Foundry Society
• /
• v.21 no.4
• /
• pp.232-238
• /
• 2001

Experimental study on the twin roll strip casting of BCuP-5(Cu-15wt%Ag-wt5%P) alloy was carried out using laboratory scale horizontal type twin roll caster. In this study, among the various operating parameters, such as tundish angle, contact angle, pouring temperature, roll speed, presetting gap of the rolls and kinds of roll and tundish materials, effect of pouring temperature for strip casting of BCuP-5 alloy which has long freezing range of about $170^{\circ}C$ was mainly investigated. BCuP-5 alloy strip was successfully produced when pouring molten metal at lower temperature than its liquidus temperature. Microstructure of the cast strip consists of primary Cu and eutectic. Especially the size of primary Cu phase increased with decreasing of pouring temperature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.8
• /
• pp.1056-1067
• /
• 1997

Present study visualized flow pattern and investigated spray characteristics of twin-fluid atomization with converging-diverging nozzles. Particle sizes were measured by using the Malvern particle analyzer, and the radial size distributions were evaluated by using the tomographic transform technique. The results show that the SMD generally increases in the radial direction at a prescribed liquid flow rate and the increasing rate in the SMD becomes gradual as atomizing gas pressure increases. The SMD decreases as the liquid flow rate increases at a fixed GLR (gas/liquid mass ratio). The atomization performance of the protrusion-type nozzle turned out to be superior to that of the flush-type. However, in the case of the protrusion-type, flow separation occurs outside the liquid delivery tube when the pressure at the gas nozzle chamber is high enough, which may deteriorate the atomization performance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.1
• /
• pp.189-205
• /
• 1996

The twin-roll type strip continuous casting process(or direct rolling process) of steel materials is characterized by two rotating water cooled rolls receiving a steady supply of molten metal which solidifies onto the rolls. A solidification analysis of molten metal considering phase transformation and thermofluid is performed using finite diffefence method with curvilinear coordinate to reduce computing time and molten region analysis with arbitrary shape. An enthalpy-specific heat method is used to determine the temperatures inthe roll and the steel. The temperature distribution of cooling roll is calculated using two dimensional finite element method, because of complex roll shape due to cooling hole in rolls and improvemnt accuracy of calculation result. The energy equaiton of cooling roll is solved simultanuously with the conservation equaiton of molten metal in order to consider heat transfer through the cooling roll. The calculated roll temperature is compared to experimental results and the heat transfer coefficient between cooling roll surface and rolling material(steel) is also determined from comparison of measured roll temperature and calculated temperature.

• Korean Journal of Materials Research
• /
• v.21 no.3
• /
• pp.168-173
• /
• 2011

Precipitation of the ordered icosahedral quasicrystal in Mg-6wt%Zn-1wt%Y alloy has been characterized by transmission electron microscopy observations. The lamellar-type icosahedral qusicrystal phases (I-phase) with the face-centered icosahedral (FCI) structure are observed in alloy after solution treatment at $550^{\circ}C$. In the alloy annealed at $400^{\circ}C$, polygon-shaped I-phases are observed in the ${\alpha}$-Mg matrix. The interfaces of the I-phase with the matrix are facetted and the facets are on five-fold and two- fold plane of the I-phase. The orientation relationship of the I-phase with the matrix is determined to be $[I5]_I//[001]_{Mg}$, $(2f)_I//(2\overline{1}0)_{Mg}$ and $[I2]_I//[311]_{Mg}$, $(5f)_I//(0\overline{1}1)_{Mg}$. The icosahedral grains are occasionally found to be twinned with one of the five-fold axis as the twin axis. The twin boundaries appear to be fairly straight and perpendicular to the fivefold twin axis. The icosahedral twin can be expressed as a rotation of $63.4^{\circ}$ or $116.62^{\circ}$ around two fold zone axis.