• Journal of Ocean Engineering and Technology
• /
• v.35 no.2
• /
• pp.99-112
• /
• 2021

The prediction of maneuverability is very important in the design process of an underwater vehicle. In this study, we predicted the steady turning ability of a symmetrical underwater vehicle while considering interactions between the yaw rate and drift/rudder angle through a simulation-based methodology. First, the hydrodynamic force and moment, including coupled derivatives, were obtained by computational fluid dynamics (CFD) simulations. The feasibility of CFD results were verified by comparing static drift/rudder simulations to vertical planar motion mechanism (VPMM) tests. Turning motion simulations were then performed by solving 2-degree-of-freedom (DOF) equations with CFD data. The turning radius, drift angle, advance, and tactical diameter were calculated. The results show good agreement with sea trial data and the effects on the turning characteristics of coupled interaction terms, especially between the yaw rate and drift angle.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.55 no.3
• /
• pp.273-283
• /
• 2019

The authors has predicted the maneuvering characteristics of a fishing vessel in deep water using Kijima's empirical formula in a previous study. Since the Kijima's empirical formula was developed by a regression analysis of merchant vessels which have dimensions ($C_b$, L/B, etc.) that are different from those of fishing vessels, it was possible to make a prediction approximately even with inaccurate estimation. In this study, the authors estimated the turning-motion characteristics of a model ship of fisheries training ship in shallow water based on the results of its previous study. The turning-motion characteristics of the model ship in shallow water was found out through quantitative analysis according to the water depth to ship draft ratio (H/d). In conclusion, the turning-motion characteristics of the model ship had significant changes immediately after an H/d 1.5, and this result will be helpful for sailing in shallow water.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.1
• /
• pp.132-141
• /
• 1995

This paper presents a choosing method of turning devices for stable robotic assembly based on verification of a base assembly motion instability. In flexible assembly application, the base assembly needs to be maintained in its assembled state without being taken apart. Therefore, the instability of the base assembly motion should be considered when determining the guide line of choosing turning devices by evaluating a degree of the motion instability of the base assembly. To derive the instability, first we inference collision free assembly directions by extracting separable directions for the mating parts and calculate the separability which gives informations as to how the parts can be essily separated. Using these results, we determine the instability evaluated by summing all the modified separabilites of each component part within base assembly.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.4
• /
• pp.13-20
• /
• 2006

A platform diving with categorizing 624C motion was video taped and 3D kinematic variables were analyzed. This motion is consist of 3 parts from the headstand position to the act of turning after take-off. The results indicated that it took a very short time from the moment of take-off to the act of 1/2 turning because the turning motion has already started from preparing motion even before the fingertips have parted from the ground. Also, there was barely any jumping height due to the use of upper limbs segment and there was little difference in the moving distance compared to the standing events judging from horizontal movement of 1.1m. The horizontal velocity of the center of human body was increased before take-off while the vertical velocity was decreased right after take-off and the velocity of lower limbs segment was faster than the upper limbs segment showing contrary results to the standing events. In the aspects of angular velocity, the upper limbs segment starts the turning motion when take-off by rapidly extending its angular velocity while lower limbs segment make large angular velocity even before take-off.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.131-137
• /
• 2014

The SUV has a risk of rollover because of the highness of center of mass. In this paper the roll-behavior of a SUV in turning motion is analyzed. Dynamic model of the vehicle on the slope is developed and simulation is carried out using the software ADAMS/Car. The results show that the relational expression between the ground force acting on the tire and the roll motion is well established. It is also identified that the driving state of the vehicle becomes unstable at the lower or upper position of the slope.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1768-1771
• /
• 2003

Hard turning replaces grinding for finishing process with expectations of higher productivity and demanded surface quality. Especially for the surface roughness as surface quality demanded in finishing process of hard turning, know-how of machining characteristics of hardened materials by cutting force analysis should be accumulated in company with achievement of precision of elements and high stiffness design technology in hard turning. Considering chip formation mechanism of hardened materials, adequate cutting conditions are selected for machining experiments and cutting forces are measured according to cutting conditions. Increase of cutting forces especially thrust force and increase of dynamic instability could occur in hard turning. Analysis of dynamic characteristics of the cutting forces is executed to investigate relation between dynamic instability and surface roughness in hard turning. Investigation on effects of relative motion of machining system generated by vibration due to dynamic instability shows that ultimate surface roughness could be predicted considering relative motion of machining system with geometrical surface roughness.

• Journal of Mechanical Science and Technology
• /
• v.16 no.1
• /
• pp.83-93
• /
• 2002

This paper presents a motion control method and its simulation results of a mobile robot for a lattice type welding. Its dynamic equation and motion control methods for welding speed and seam tracking are described. The motion control is realized in the view of keeping constant welding speed and precise target line even though the robot is driven for following straight line or curve. The mobile robot is modeled based on Lagrange equation under nonholonomic constraints and the model is represented in state space form. The motion control of the mobile robot is separated into three driving motions of straight locomotion, turning locomotion and torch slider control. For the torch slider control, the proportional-integral-derivative (PID) control method is used. For the straight locomotion, a concept of decoupling method between input and output is adopted and for the turning locomotion, the turning speed is controlled according to the angular velocity value at each point of the corner with range of 90$^{\circ}$ constrained to the welding speed. The proposed control methods are proved through simulation results and these results have proved that the mobile robot has enough ability to apply the lattice type welding line.

• Korean Journal of Applied Biomechanics
• /
• v.22 no.2
• /
• pp.173-181
• /
• 2012

The purpose of this study was to research on the movement of Fouette A La Second which was a type of turning movements on cheerleading. This research was conducted for helping cheerleaders to improve their overall skills. The three cheerleading national team members were participated in this research and the movements of Fouette A La Second were recorded with 6 digital motion master 60 video cameras, operating at a sampling frequency of 60 fields/sec. Six out of ten turning motion data were collected and analyzed with Kwon3D XP. The results were as follow: 1) The subject A's Releve motion was not executed precisely because of the COG's unstability. So she was required to improve the balancing ability. 2) The subject B could not execute the precise A La Second motion because of subject B's large hip angle. By tracing the projection of B's right toe on x-y plane, the subject made an elliptical orbit. Because B did not have a proper turning skills she needed to improve the muscle power and flexibility. She also needed to move quickly from Releve to Plie movement. 3) The subject C could not execute the Plie movement precisely, so she could not turn her body correctly around a certain spot. The subject C needed to decrease the knee angle at the Plie motion.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.2
• /
• pp.30-38
• /
• 2003

This paper proposed PID controller for torch slider and PD controller for motor right wheel. to control the motion of two-wheeled welding mobile robot with seam tracking sensor touched on welding line. The motion control is realized in the view of keeping constant welding velocity and precise seam tracking even though the target welding line is on straight line or curved line. The position and direction of the body of the mottle robot are controlled by using signal errors between seam tracking sensor and body positioning sensor attached on the end of torch slider and body side of the mobile robot, respectively. In turning motion, the body and the torch slider are controlled by using the kinematic model related with two motions of body turning and torch sliding. The straight locomotion is controlled according to eleven control patterns obtained from displacements between two sensors of the seam tracking sensor and the body positioning sensor. The effectiveness is proven through the experimental results fur lattice type welding line. Through the experimental results, we can see that the position value of the electrode end point and the welding velocity are controlled almost constantly both in straight and turning locomotion.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.319-324
• /
• 2001

This paper presents the motion control of a mobile robot with arc sensor for lattice type welding. Its dynamic equation and motion control method for welding speed and seam tracking are described. The motion control is realized in the view of keeping constant welding speed and precise target line even though the robot is driven along a straight line or corner. The mobile robot is modeled based on Lagrange equation under nonholonomic constraints and the model is represented in state space form. The motion control of the mobile robot is separated into three driving motions of straight locomotion, turning locomotion and torch slider controls. For the torch slider control, the proportional integral derivative (PID) control method is used. For the straight locomotion, a concept of decoupling method between input and output is adopted and for the turning locomotion, the turning speed is controlled according to the angular velocity value at each point of the comer with range of $90^{\circ}$ constrained to the welding speed. The experiment has been done to verify the effectiveness of the proposed controllers. These results are shown to fit well by the simulation results.