• 한국농공학회지
• /
• 제18권2호
• /
• pp.4096-4104
• /
• 1976

This experiment was carried out to investigate the efficient turning method which will be able to use every cutting methods, to calculate the width of the center field which must transpose from rotary cutting method to return cutting method, to investigate the effects of L/W and unit field on the operation efficiency. The results are summarized as follows: 1. In case of cutting in the outer field, the efficient turning method is the "$\alpha$" type turning method (half U-shaped turning method) at the first rotation, is the "$\beta$" type turning method (T-shaped turning method) at the second to fourth rotation. 2. In case of cutting in the inner field, the efficient turning method which takes the least turning time is the "a" type turning method ($\Delta$-shaped turning method). 3. The width of the center field (W') changes by the length-width ratio (L/W) and width (W), W' is 9.0m in case that L/W is 2.5 and W is 30m. 4. The larger L/W and area of unit field (A) become, the more operation efficiency (E) increases, and the limits that E is affected signicantly by L/W is 2 to 3.5 and A is within 5,000$m^2$. within 5,000$m^2$.

• 한국산학기술학회논문지
• /
• 제16권3호
• /
• pp.1639-1644
• /
• 2015

볼밸브용 볼의 로봇 육성용접시스템에서 포지셔너의 설계 및 구조강도 해석에 관한 연구를 하였다. 포지셔너의 일부분인 터닝 유닛을 모델링하였고, 보로 가정하여 해석을 진행하였다. 볼의 무게가 $9,000kg_f$ 일 때 터닝 유닛에 가해지는 응력이 366.85MPa로 나왔다. 이 값은 재료의 항복강도보다 높은 값이다. 앞의 결과를 토대로 터닝 유닛을 수정하여 모델링을 하였다. 수정된 모델링으로 해석한 결과, 응력의 값은 296.11MPa로 확인되었다. 이 값은 재료의 항복강도보다 낮은 수치이며, 볼의 무게를 버티는 것을 알 수 있었다.

• 한국산학기술학회논문지
• /
• 제13권11호
• /
• pp.4944-4949
• /
• 2012

이 논문의 목적은 작업장에서 사용하기 위한 에어건의 개발에 관련된 것이다. 에어건은 공작기계를 사용하는 산업현장에서 공작물 칩과 절삭유의 제거를 위한 도구이다. 그리고 그것은 일반적으로 압축공기를 분사하는 용도로 사용된다. 작업자는 에어의 흡입과 분사를 위해 각각의 에어건을 준비하여야 한다. 따라서 우리는 새로운 에어건을 개발하였다. 이 논문에서 우리는 에어건의 설계와 분석을 위한 연구를 한다. 에어건은 몸체, 파이프, 개폐 유닛, 전환 유닛, 에어 튜브 그리고 조립을 위한 요소들로 구성된다. 개발된 에어건은 그 효율을 확인하기 위해 실험된다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1991년도 춘계학술대회 논문집
• /
• pp.243-250
• /
• 1991

This paper concerns the development of NC programming system TIG (Turning with Interactive Graphics) with interactive graphics for turning operation. The system cosists of the processor, the post-processor and the system-user interface. Different from previous segment contour based NC graphic programming systems, the frliability and efficiencyof programming is realized by using Boolean operation with block unit based ICONs for the geometry definition. The tool motion can be also displayed on the screen together with the part contour. The system calculate automatically the number of passes based on the user specified cutting conditions.

• Journal of Animal Science and Technology
• /
• 제64권2호
• /
• pp.365-379
• /
• 2022

The present study was conducted with the aim of investigating the effect of storage length, turning frequency and egg position on internal quality traits of chukar eggs obtained from 56-week-old chukar partridges under the same nutrition and management conditions. A total of 720 eggs were collected and assigned to 36 subgroups according to storage length (7, 14, 21, and 28 d), turning frequency (0, 1, and 24 per day) and egg position (pointed end up, blunt end up and horizontal). As a result of the study, almost all the internal quality traits of chukar eggs were negatively affected by lengthening of storage period especially 21 days and longer (p < 0.001). Internal egg quality traits weren't statistically affected by turning frequency except yolk index (p < 0.01). An improvement was observed in Haugh unit, albumen index and heigh of eggs stored with pointed end up (p < 0.001). Some significant interactions occurred among all internal egg quality traits which were mostly dependent on the eggs stored horizontally, extended storage time more than 21 days and egg turning during storage. The results and interactions showed that internal quality traits would be preserved well for the eggs stored less than 21 days with the position of pointed end up independent of turning. If the storage period was to exceed 21 days, the eggs should be positioned horizontally and turning should be applied to preserve the quality of chukar eggs.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.1025-1028
• /
• 2002

In this paper, a micro-turning lathe is introduced for micro machining of aluminum rod. To give feed motion, stepwise motion[2] actuators are used instead of the conventional inchworm mechanism. These are consisted of two Piezoelectric ceramics; one is for feeding the slider, and the other is for clamping the slider in the guide way of the body. The guide is V-form. The linearity and positional accuracy of the actuators is good enough far high precision motion. Since the system is more compact than the conventional system using three Piezoelectric ceramics, it is applicable for the micro-machine or MEMS unit. To fabricate the lathe, a small spindle unit with ball bearings of diameter of 10 millimeter is built-up on the top the slider. The motion is feed backed with miniaturized linear encoder attached each axis slider. The diamond tool bite is used for cutting tool. The machining is tried to make small diameter rod. The possible diameter that can be machined in this machine is presented as well as chip formation, surface roughness, and machinability.

• Journal of Korean Biological Nursing Science
• /
• 제11권1호
• /
• pp.92-98
• /
• 2009

Purpose: This study was aimed to investigate the colony counts by different disinfecting processes and duration of the operation for humidifiers in an intensive care unit (ICU) in Busan. Method: The four steps of disinfecting process were taken with four different humidifiers according to the use of disinfectant (1:100 $Deconex^{(R)}$ 50FF/nothing) and refilling water (tap water/distilled water). First, the colony counts using water sample from wick was conducted at 0 hr, 24 hr, and 48 hr respectively after turning on the humidifiers. Next, the colony counts using waterdrop from the outlet was done at 0 hr, 24 hr, 48 hr, and 72 hr respectively after turning on the humidifiers. Result: No colony was counted after disinfecting with 1:100 $Deconex^{(R)}$ 50FF until 72 hr after turning on the humidifiers. However, without disinfecting with $Deconex^{(R)}$ 50FF, the colony count was increased in the humidifiers from 24 hr after turning on the humidifiers. The result was the same regardless of the refilling water. Conclusion: According to the results, the study found that disinfection of humidifiers in the ICUs with 1:100 $Deconex^{(R)}$ 50FF every 72 hr is effective to remove general bacteria.

• 한국항해항만학회지
• /
• 제33권9호
• /
• pp.603-608
• /
• 2009

In this paper, a 3m-class free running model ship will be introduced with its manoeuvring performance experiments. The results of turning circle test and zig-zag test will be explained. The developed system are equipped with GPS, main control computer, wireless LAN, IMU (Inertial Measurement Unit), self-propulsion propeller and driving rudder. Its motion can be controlled by RC (Radio Control) and wireless LAN from land based center. Automatic navigation is also available by pre-programmed algorithm. The trajectory of navigation can be acquired by GPS and it provides us with important data for ship's motion control experiments. The results of manoeuvring performance experiment have shown that the developed free running model ship can be used to verify the test of turning circle and zig-zag. For next step, other experimental researches such as ship collision avoidance system and automatic berthing can be considered in the future.

• 한국생산제조학회지
• /
• 제20권3호
• /
• pp.350-356
• /
• 2011

In this paper, we proposed the automatic cutting mechanism of the perforation pipes in an automobile muffler. This cutting mechanism makes continuous work possible, because it performs the batch work via the sequential operation of loading, feeding, cutting, and discharging. The proposed cutting mechanism consists of the frame unit, escape unit, turning unit, feeding unit, vision system, clamping unit, spindle/cutting unit and cooling unit. And, these mechanisms have been modularized through mechanical, dynamical and structural optimized design using the SMO (SimDesigner Motion) analysis module. Also, the virtual prototype was carried out using the 3-D CAD program. The cutting process cycle is performed in the order of loading, vision processing, feeding, clamping, cutting and discharging. And the cycle time for cutting one piece was designed to be completed in four seconds.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.584-589
• /
• 2008

A bi-modal tram has been developing to consist of articulated-two cars propelled by CNG hybrid (series type) in Korea since 2003. All wheels are driven by electrical motors independently, which can eliminate differential gears to reduce turning radius and make low floor to provide the old and the handicapped with easy access. In the bi-modal tram, therefore, reduction gear unit is key technology to make low floor and drive wheels independently. This study was aimed at performance evaluations of the reduction gear unit for the bi-modal tram. Oil leakage, oil temperature, vibration, acoustic noise in idle operations were measured for the reduction gear unit of the bimodal tram.