• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2591-2596
• /
• 2007

The effect of incidence angle on the three-dimensional flow and aerodynamic loss in the downstream region of a high-turning turbine rotor blade has been investigated with a straight miniature five-hole probe. The incidence angle is changed to be +10, +5, 0, -10, -20, -30 and -40 degrees. The results show that the positive incidence reinforces the three-dimensional vortical flows within the turbine passage including the passage vortex, but the negative incidence weaken them significantly. A small increment in the positive incidence angle results in a remarkable aerodynamic loss increase, while increasing the incidence angle in the negative range leads to a very small change in the aerodynamic loss.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.397-401
• /
• 2003

In this work, diamond turning process is used to produce mirror surface on a Al cone. The Al cone as used as a mirror which can reflect a laser beam without scattering and, hence, it is critical to minimize the surface roughness of a Al cone. During diamond turning, feedrate and tool nose radius are changed to investigate characteristics of the ultra precision machined surface of a Al cone. A laser beam of 633 nm is applied to examine the effect of surface roughness on the characteristics of reflectivity. It is found that surface roughness is not significantly affected by feedrate. The main factor influencing surface roughness is tool nose radius. The line patterns of reflected laser beams show that the minimum surface roughness of 0.08 $\mu\textrm{m}$ (Ra) is required to avoid scattering phenomena of reflectivity.

• 한국공작기계학회논문집
• /
• 제12권6호
• /
• pp.44-49
• /
• 2003

To obtain the surface roughness with range from 10nm to 1nm we need the study of ultra-precision machine, cutting condition, and materials. In this paper, the optimal cutting conditions for getting mirror surface of aluminum alloy have been examined experimentally by using ultra-precision turning machine and sing1e crystal diamond tool. In generally, the cutting conditions such as feed rate and depth of cut have effect on the surface roughness in ultra-precision turning. The result of surface roughness was measured by the ZYGO New View 200. Therefore, The surface roughness and cutting conditions has been clarified. The smooth surface of aluminum alloy less than 1nm RMS, 1nm Rmax can be obtained by the ultra-precision cutting.

• 한국공작기계학회논문집
• /
• 제10권2호
• /
• pp.89-94
• /
• 2001

This paper presents a study of surface roughness prediction model by orthogonal design in turning operation. Regression analysis technique has been used to study the effects of the cutting parameters such as cutting speed, feed depth of cut, and nose radius on surface roughness. An effect of interaction between two parameters on surface roughness has also been investigated. The experiment has been conducted using coated tungsten carbide inserts without cutting fluid. The reliability of the surface roughness model as a function of the cutting parameters has been estimated. The results show that the experimental design used in turning process is a method to estimate the effects of cutting parameters on sur-face roughness.

• 대한수학회지
• /
• 제51권4호
• /
• pp.679-702
• /
• 2014

Investigation of the numerical solution of singularly perturbed turning point problems dates back to late 1970s. However, due to the presence of layers, not many high order schemes could be developed to solve such problems. On the other hand, one could think of applying the convergence acceleration technique to improve the performance of existing numerical methods. However, that itself posed some challenges. To this end, we design and analyze a novel fitted operator finite difference method (FOFDM) to solve this type of problems. Then we develop a fitted mesh finite difference method (FMFDM). Our detailed convergence analysis shows that this FMFDM is robust with respect to the singular perturbation parameter. Then we investigate the effect of Richardson extrapolation on both of these methods. We observe that, the accuracy is improved in both cases whereas the rate of convergence depends on the particular scheme being used.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.605-609
• /
• 1996

Continuous sliding mode control is applied to turning process for cutting force regulation. The highest feedrate compatible with the allowable cutting force is applied in rough cutting process such that maximum productivity is ensured and tool breakage is avoided. The programmed feedrate is overridden after the control algorithm is carried out. However, most CNC lathe manufacturers offer limited number of data bits far feedrate override, thus resulting in nonlinear behavior of the machine tools. Such nonlinearity brings “quantized” effect, and the optimal faedrate is rounded off before being fed into the CNC system. To compensate for this problem, continuous sliding mode control is applied. Conventional switching control law at a sliding surface is replaced by a smooth control interpolation in a selected boundary layer to avoid the excitation of high-frequency dynamics. Simulation results are presented in comparison with those obtained by applying adaptive control.

• 한국산업융합학회 논문집
• /
• 제7권1호
• /
• pp.55-62
• /
• 2004

The presence of cutting fluid for cutting tool and workpiece leads a temperature decrease, and reduces tool wear and residual stress. Moreover, it disposes chips from cutting area, and reduces thermal distortion. However, in manufacturing, cutting fluid used in cutting process is undesirable for both human and environmental aspect. Also, it's not economic for cutting cost. This paper studied experimentally the effects of cutting parameters on the characteristics of mist generation in turning. The results of experiment are as follows: 1) The more severe cutting conditions the more mist generate, 2) The ratio of weight concentrations of cutting fluid nearly have no an effect on the amounts of mist generation 3) The size of SMD is not affected by cutting parameters.

• 한국기계가공학회지
• /
• 제8권3호
• /
• pp.74-81
• /
• 2009

At present, industries and researchers are looking for ways to reduce the use of lubricants because of ecological and economical reasons. Therefore, metal cutting is to move toward dry cutting or semi-dry cutting. One of the technologies is known as MQL machining. This paper presents an investigation into MQL machining with the objective of evaluating cylindricity and cooling effect for the turning process of SM45C. To reach this goal, cylindrical-outer-diameter turning experiments are carried out according to cutting conditions with fluid, MQL and dry machining methods. A cutting force, tool-shank temperature and cylindricity of workpiece are measured and analyzed. The correlation between cutting conditions and cylindricity are evaluated according to cooling lubricant environments.

• 한국결정성장학회지
• /
• 제24권6호
• /
• pp.274-278
• /
• 2014

가공정밀도 요구특성의 지속적인 향상에도 불구하고, 공작기계와 절삭공구를 이용한 절삭가공공정에서의 채터진동은 아직도 개선의 여지가 많이 남아있다. 특히, 더욱 고속화, 고정밀화 되고 있는 가공현장에서 채터진동의 효과적인 감소대책에 대한 다양한 연구가 필요하다. 본 연구에서는 이러한 문제점을 해결하기 위해 고정밀 공구동력계를 이용한 실시간 절삭력 측정과 유한요소해석 방법을 이용해 사용 빈도와 활용이 매우 큰 터닝센터(turning center)에서 폭넓게 적용되고 있는 3종의 절삭공구 툴링에서의 채터진동 특성을 평가하여, 공구형상 및 툴링 특성에 따른 채터진동과의 상관성을 연구하고, 향후 채터진동 저감형 공구개발을 위한 근간 기술자료로 활용코자 한다.

• 대한가정학회지
• /
• 제49권7호
• /
• pp.67-80
• /
• 2011

This study investigated a path model in which men's and women's communication behavior escalating marital conflict (CBEMC) may be influenced directly and indirectly, via negative interpretations of their spouse, by their spouse's problem behavior, the couple's turning toward bids, and dyadic perspective-taking. Self-report data were collected from 498 married men and women who were living in Busan, Korea. Multiple-group analysis revealed that the path model was not equivalent for men and women. Their couple's turning toward bids and dyadic perspective-taking for men, and their spouse's problem behavior and dyadic perspective-taking for women, had direct effects on CBEMC. Further, their spouse's problem behavior and the couple's turning toward bids had indirect effects on CBEMC through negative interpretations in both men and women. The indirect effect of dyadic perspective-taking on CBEMC was significant only for men. Finally, considering total effects, dyadic perspective-taking was the strongest predictor of CBEMC for both genders.