• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.327-330
• /
• 2003

In this work, current-voltage characteristics with time of NPT(Non-PunchThrough) IGBT is proposed during turn-on and turn-off by using analytical method. From the results, power loss at turn-off dominates the total electrical loss with respect to that at turn-on. The results have been compared with those of PSPICE and show the identical trend of power loss with each other.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.43-53
• /
• 2007

We have analyzed low current operation characteristics of a VCSEL transmitter operating at fixed Current over wide temperature range. Used 850 nm oxide VCSEL has low temperature dependence of the threshold current and $d^2I_{th}/dT^2$ is approximately $1.346\times10^{-4}mA/^{\circ}C^2$. We fixed on-current so that output power from the chip is 1 mW at $20^{\circ}C$ and investigated the turn-on, turn-off characteristics and eye-diagram of the 850 nm oxide VCSEL transmitter with varying ambient temperature and off-current. We measured rise time, fall time, extinction ratio and timing jitter by changing tile ambient temperature and off-current. With the fixed off-current of around $0.1\sim0.2mA$ lower than the lowest threshold current the transmitter successfully operated at 1.25 Gbps over a wide temperature range from $-20^{\circ}C$ to $80^{\circ}C$.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.243-246
• /
• 2001

The control of the SRM(Switched Reluctance Motor) is usually based on the non-linear inductance profiles with positions. So determination of optimal switching angle is very different. This paper proposed that the determination method of turn-on/off angle in the SRM drives is to maintain the high torque, which is realized by using self-tuning control method. During the sampling time, a number of pulses from the encoder are checked by using micro-controller. And compared with pre-checked a number of pulses. After calculating difference between two data, turn-on/off angle moves forward or backward direction by using self-tuning method. The optimal turn-on/off angle is determined by iterating such a process and the maximum torque is maintained. Experimental results are provided to demonstrate the validity of the self-tuning controller.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.668-676
• /
• 1998

A passive energy recovery snubber for high-power-factor boost rectifier, in which the main switch is described in terms of the equivalent circuits that are operational during turn-on and turn-off sequences. These equivalent circuits are analyzed so that the overshoot voltage across the main switch, the snubber current, and the turn-off transition time can be predicted analytically. The main switch combined with proposed snubber can be turned on with zero current and turned off at limited voltage stress. The high-power-factor boost rectifier with proposed snubber is implemented, and the experimental results are presented to confirm the validity of proposed snubber.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.241-245
• /
• 1998

This paper gives the novel design of compensated ring anode-short for power GTO thyristor. By means of this design the power GTO of $\Phi$63.5mm 2500A/4500V reaches more uniform turn-off compared with conventional ring short GTO, resulting in higher turn-off ability and low tail current/tail time.

• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.257-258
• /
• 2011

This paper describes a new method for the seamless operation mode transfer of a PCS with minimized voltage disturbance. The proposed method provides reduced STS turn off time after line fault and smooth mode change between current and voltage control of the PCS. The usefulness of the method is verified through simulations with the consideration of the time delay in detecting a line fault and SCR turn-off time.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1023_1024
• /
• 2009

In this paper, a novel 10kV, 50A, 50kHz pulsed power supply based on IGBT stacks is proposed. Proposed scheme consists of series connected 12 IGBT to generate maximum 10kV output pulse and 10kW full bridge phase-shifted zero voltage switching converter to charge DC capacitor voltage. Each IGBTs are sustain the 830V of capacitor voltage at turn off interval. By turn on the each IGBT for the same time it gives the path for the series connection of charged capacitor. From above turn on and off procedure, high voltage repetitive pulse is applied to the load. The synchronization of gating signal is important of series operation of IGBTs. For gating signal synchronization, specially designed gate power circuit using full bridge inverter and pulse transformer is developed to generate IGBT gating signal.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.5-8
• /
• 2018

Recently, global warming and tropical nights have caused the use of electric fans to explode. Under these circumstances, running the fan for long periods of time is not only a risk of explosion due to overloading the power but also a small amount of electricity and environmental pollution. Therefore, the research was conducted to develop devices that automatically turn fans on and off according to room temperature, reducing the risk of explosion as well as saving energy. This study suggested that electric fans turn on and off automatically and display temperature in mobile applications. The ability to turn on and off allows the fan to turn on itself if the indoor temperature rises above a certain level. Conversely, if the indoor temperature drops below a certain level, the fan should be turned off. Second, the temperature display function checks indoor temperature through mobile applications. The automatic on/off capabilities proposed in this study could contribute to reducing the risk of explosion and saving energy. However, if the indoor temperature rises above a certain temperature even though there is no one inside, the fan can be turned on. The expectation from this study is that the ability of fans to operate and turn off at appropriate temperatures can reduce the risk of explosion, electrical charges, and environmental pollution.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.694-697
• /
• 2003

In applying LCD to TV application, one of the most significant factors to be improved is image sticking on the moving picture. LCD is different from CRT in the sense that it's continuous passive device, which holds images in entire frame period, while impulse type device generate image in very short time. To reduce image sticking problem related to hold type display mode, we made an experiment to drive LCD like CRT. We made articulate images by turn on-off backlight, and we realized the ratio of Back Light on-off time by adjusting between on time and off time for video signal input during 1 frame (16.7ms). Conventional CCFL (cold cathode fluorescent lamp) cannot follow fast on-off speed, so we evaluated new fluorescent substances of light source to improve residual light characteristic of CCFL. We realized articulate image generation similar to CRT by blinking drive. As a result, reduced image sticking phenomenon was validated by naked eye and response time measurement.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.10
• /
• pp.713-718
• /
• 1987

A new method for the modeling of non-ideal dc-dc converters whose switching times are finite is proposed. The effects of finite turn-on, turn-off times, delay time, storage time, reverse recovery process on the system stability, dc transfer function and efficiency are investigated. It is verified how system poles are changed and how dc transfer function and efficiency are decreased by non-ideal switching.