• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.55-62
• /
• 2003

This paper describes the effect of the incidence angle on the turbulence structure in the wake of a turbine rotor blade at the low inlet free-stream turbulence level. For three incidence angles of -5, 0 and 5 degrees, mid-span energy spectrum as well as mid-span profiles of mean velocity magnitude and turbulence intensity are reported at three downstream locations in the wake. Vortex shedding frequencies are obtained from the energy spectrum. The result shows that as the incidence angle changes from-5 to 5 degrees, the boundary layer on the suction surface tends to be thickened, which results in widening of the wake. Strouhal numbers based on the shedding frequencies have a nearly constant value of 0.3, independent of tested incidence angles.

• 대한기계학회논문집B
• /
• 제20권7호
• /
• pp.2277-2288
• /
• 1996

This study was performed to analyze the cooling effect of heated ribs which are frequently used for cooling of electronic parts, using the numerical method. To prevent the excessive pressure drop due to turbulence promoters for the enhancement of heat transfer rate especially, the effect of the angle of turbulence promoter was investigated by the numerical analysis. Heat transfer rate with turbulence promoters with rectangular cross-section increased by 13% in average, but the coefficient of pressure drop increased by 1.68 times than that without them. In the present study, triangular cross-sectional shape turbulence promoters were suggested and numerically tested. Pressure drop of turbulence promoter with the 30 degree triangular cross-sectional shape decreased by 30% from that of rectangular cross-section promoters while heat transfer rate was almost the same. While with 4 turbulence promoters, the heat transfer rate increased by 21%, the pressure drop increased 4 times. It means that the higher capacity of cooling fan should be needed. With the triangular cross-sectional shape, the size of vortex region at the rear of promoters became considerably smaller, so pressure drop became smaller. The effect of the change of cross-sectional shape was not found in the flow pattern near the ribs, so that heat transfer characteristics in the ribs were not changed.

• 대한기계학회논문집B
• /
• 제27권6호
• /
• pp.813-820
• /
• 2003

The purpose of this research is to develop the model of turbulence modulation due to the presence of particles in various types of particle-laden flows Available experimental data are surveyed and the dependence of turbulence modulation of carrier-phase on particle size, concentration and. particle Reynolds number are examined. This study takes into account the effect of wake produced by particle, the drag between phases and the velocity gradient in the wake to estimate the production of turbulence. The model of turbulence modulation using the mixing length theory under the assumption of equilibrium flow is proposed. Numerical results show that the model is successful in predicting the characteristics of the particle-laden in various flow conditions both qualitatively and quantitatively.

• 대한기계학회논문집
• /
• 제18권4호
• /
• pp.920-932
• /
• 1994

The combustion phenomena of a reciprocating engine is one of the most important processes affecting performance and emissions. One effective way to improve the engine combustion is to control the motion of the charge inside a cylinder by means of optimum induction system design, because the flame speed is mainly determined by the turbulence at compression(TDC) process in S.I. engine. It is believed that the tumble and swirl motion generated during intake breaks down into small-scale turbulence in the compression stroke of the cycle. However, the exact nature of their relationship is not well known. This paper describes cycle resolved LDV measurement of turbulent flow inside the cylinder of a 4-valve engine under motoring(non-firing) conditions, and studies the effect of intake port configurations on the turbulence characteristics using following parameters ; Eulerian temporal autocorrelation coefficient, turbulence energy spectral density function, Taylor micro time scale, integral time scale, and integral length scale.

• 한국추진공학회지
• /
• 제15권4호
• /
• pp.57-64
• /
• 2011

펄스 데토네이션 엔진에서와 같이 탄화수소를 연료로 하는 데토네이션 파는 강한 불안정성을 가지며 난류 연소 효과를 고려한 연구를 수행하여야 함이 제시된 바 있다. 본 연구에서는 강한 불안정성을 가지는 데토네이션 파의 구조를 이해하기 위하여 비점성 해석, 점성 해석, 난류 모델 및 간단한 난류 연소 모델을 고려한 수치 해석 연구를 수행하였다. 모델링 수준에 따른 연구를 통하여 점성 및 난류는 저주파 특성에는 거의 영향이 없으나, 고주파 특성을 강화하는 경향이 있는 것으로 보인다. 한편, 데토네이션 연구를 위한 난류-연소 상호 작용 모델에는 활성화 에너지의 영향이 고려되어야 하는 것으로 여겨진다.

• 디지털융복합연구
• /
• 제19권9호
• /
• pp.95-103
• /
• 2021

본 연구는 동료 신뢰성의 개별차원과 개인적 양면성의 영향 정도를 직접 분석하고, 시장변동성의 조절효과도 검정하였다. 본 연구에서 반영한 시장변동성은 외부환경에 대한 변화 대응능력으로써 시장에서 소비자의 기호와 수요변화의 정도를 의미한다. 연구대상은 설문조사에 참여한 IT 부품 공급업체의 엔지니어 411명이며, 그 결과는 SPSS 21.0과 AMOS 21을 사용하여 분석하였다. 연구결과는 다음과 같다. 첫째, 신뢰성 개별차원과 개인적 양면성의 관계를 분석한 결과, 능력과 진정성은 개인적 양면성에 유의미한 영향을 미치고 있는 것으로 나타났다. 둘째, 신뢰성의 개별차원과 개인적 양면성의 관계에서 시장변동성은 능력과는 부(-)의 상호작용 효과를 나타내며, 진정성과는 정(+)의 상호작용 효과를 나타내어 신뢰성과 개인적 양면성 간에 조절역할을 하는 것으로 확인되었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.35.1-35.1
• /
• 2011

When the wind speed is measured by the met-mast sensor it is distorted due to the shadow effect of tower. In this paper the tower shadow effect is analyzed by a computational fluid dynamics code. First three dimensional modeling and flow analysis of the met-mast system were performed. The results were compared with the available experimental wind-tunnel test data to confirm the validity of the meshes and turbulence model. Two-dimensional model was then developed based on the three-dimensional works and experimental data. 2D analysis for various Reynolds numbers and turbulence strengths were then performed to establish the tower shadow effect database, which can be utilized as correction factors for the measured wind energy.

• 대한기계학회논문집
• /
• 제18권9호
• /
• pp.2443-2453
• /
• 1994

The structure of turbulence of fully developed flow through four concentric annuli with the rough outer wall was investigated experimentally for a Reynolds number range Re=15, 000-93, 000. Turbulence intensities were measured in three(u, v, w) directions, and turbulence shear stresses in annuli of radius=0.13, 0.26, 0.4 and 0.56, respectively. Due to the square roughness element attached periodically along the axial direction, the radial velocity fluctuations show similar distribution regardless of the different .alpha.cases. However, the axial and circumferential velocity fluctuation profiles demonstrate the longitudinal turbulence structures are strongly influenced by the .alpha. values. The turbulent eddy viscosity deduced form mean velocity distributions and the measured Reynolds shear stresses are also presented and discussed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2037-2042
• /
• 2003

The purpose of this research is to develop the model of turbulence modulation due to the presence of particles in various types of particle-laden flows. Available experimental data were surveyed and the dependence of turbulence modulation of carrier-phase on particle size, concentration and particle Reynolds number were examined. This study takes into account the effect of wake produced by particle, the drag between phases and the velocity gradient in the wake to estimate the production of turbulence. The model of turbulence modulation using the mixing length theory under the assumption of equilibrium flow is proposed. Numerical results show that the model is successful in predicting the characteristics of the particle-laden flow in various conditions both qualitatively and quantitatively.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.420-427
• /
• 2011

In this study, numerical simulations of transonic aircraft configurations are performed with various turbulence models and the effect of turbulence models on flow separation are examined. A three-dimensional RANS code and three turbulence models are used for the study. The turbulence models incorporated to the code include Menter's ${\kappa}-{\omega}$ model, Coakley's $q-{\omega}$, and Huang and Coakley's ${\kappa}-{\omega}$, model. Using the code, numerical simulations of DLR-F6 configurations obtained from AIAA CFD Drag Prediction Workshop are conducted. Flow separations on the wing-body juncture and the wing lower surface near pylon are observed. and flow features of the regions are compared with experimental data and other numerical results.