• Journal of Energy Engineering
• /
• v.13 no.2
• /
• pp.118-127
• /
• 2004

The purpose of this study is experimentally to analyze that intake port swirl, injection system and turbocharger have an effect on the engine performance and the emission characteristics in a V8 type turbocharged intercooler D.I. diesel engine of the displacement 16.7ι, and to suggest the improvement of engine performance. Generally to enhance engine power, TCI diesel engine is put to practically use turbo-charged intercoler in order to increase boost efficiency which is cooled boost air. As results of considering the factors of the intake port of swirl ratio 2.25, compression ratio 17.5, re-entrant 8.5$^{\circ}$ combustion bowl, nozzle hole diameter ${\Phi}$0.33*3+${\Phi}$0.35*2, nozzle protrusion 3.18mm, injection timing BTDC 12$^{\circ}$CA and turbo charger (compressor 0.6A/R+46Trim, turbine 1.0A/R+57Trim) is the best in the full range of operating in the engine performance and the exhaust characteristics of NO$\_$x/ concentration. Therefore their factors are appropriated as intake system, injection and turbocharger system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.3
• /
• pp.119-127
• /
• 2018

A test stand for an altitude test of reciprocating engine was designed, manufactured and validated by preliminary tests and simple calculations. The test stand was designed to interface with the altitude turbo-shaft engine test facility of Korea Aerospace Research Institute. Many limiting conditions for altitude test of reciprocating engine were assumed and the test stand was developed to satisfy these limitations. The test stand design was focused especially on the altitude, Mach number and fuel temperature control for reciprocating engine altitude tests with smaller air and fuel flow than those of turbo shaft engines.

• 한국기계연구소 소보
• /
• s.14
• /
• pp.111-119
• /
• 1985

A review on the design analysis of an axial-flow turbine is presented. Followed by a brief introduction to the fundamentals on an axial-flow turbine, a design procedure is described with a sample design of one for a small turbo-jet engine. Design procedure is composed of two parts: one-dimensional analysis of three-dimensional effects based on radial equilibrium theory. The method described herein is so simple and rapid that it can be applied to the preliminary design analysis of turbo-machinery equipped with axial-flow turbines.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.440-448
• /
• 2004

Toasting the 100 year anniversary of controlled, powered flight, the propulsion system used on today's aircraft represents the evolution of jet propulsion based on the gas turbine, first conceived by Whittle and Von Ohain about 70 years ago. In that period, propulsion system concepts have evolved through turbo-props, turbo-jets, low by-pass ratio(BPR) turbofans to today's high BPR 2-shaft and 3-shaft turbofans. Also, this period has seen remarkable progress in the performance, reliability environmental compatibility of these propulsion systems.(omitted)

• International Journal of Fluid Machinery and Systems
• /
• v.1 no.1
• /
• pp.47-56
• /
• 2008

The flow behind the variable area nozzle which corresponds to the flow at the leading edge of the impeller was measured with a 3-hole yaw probe and calculated with CFD. Two nozzle throat-areas were investigated. One is the smallest and the other is the largest opening for the variable nozzle. Test results agreed with the calculated results qualitatively. The leakage flow through the tip clearance of the nozzle vane significantly affected the flow field downstream of the nozzle vane with the smallest opening. However, the effect on leakage flow on the flow field downstream of the nozzle vane with the largest opening was very weak and the effect of wake is dominant.

• Journal of Aerospace System Engineering
• /
• v.4 no.1
• /
• pp.10-14
• /
• 2010

The Fuel system of T-50 Advanced Trainer is equipped with two boost pump and fuel flow proportioner for feeding fuel to turbo jet engine. when an unexpected failure occurs, they can feed the fuel to turbo jet engine which fuel quantity required. fuel quantity control method is applied for minimizing the center of gravity change. and fuel quantity control method is controlled by FQMS(Fuel Quantity Measuring System) and FFP(Fuel Flow Proportioner). This paper presents life cycle extension plans of FFP hydraulic motor by design improvements of connecting and arrangement of pipe comparing with KF-16.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.592-596
• /
• 2012

The details of engine data are essentially needed for engine modeling and simulation. But, the engine data are kept secret because the information is company's experiential property. In this paper performed the performance modeling of the mixed flow turbofan engine cycles from the general available engine data, and verify the validity.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.3
• /
• pp.109-118
• /
• 2018

Korea Aerospace Research Institute has developed a staged combustion cycle rocket (SCCR) engine with high specific impulse to send a 3-ton class satellite into geostationary orbit while conducting a Korean Space Launch Vehicle (KSLV) II project. The SCCR engine is different from the KSLV-II engine, which is an open cycle engine using a gas-generator. The SCCR engine with a closed cycle engine is composed of a pre-burner, a turbo pump, and a main combustor. The technology demonstration model (TDM0) was assembled and tested in the 7ton-class engine combustion test facility of Naro Space Center, and the combustion test was successfully conducted.

• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.27-35
• /
• 2005

In this study, a performance analysis code was developed for the off-design performance analysis of air turbo ramjet(ATR) engine, and the analyses were performed for the pre-designed ATR engine at several operating points in the envelope. Variable intake and thrust nozzle were assumed to cover the wide envelope. Mathematical models for each components were developed to calculate their off-design performance. Simple design formulas were introduced for some components to explore the performance variation versus the design parameters. As a result, the pre-defined engine couldn't cover the entire mission profile. And it was also found that the effect of the pre-cooler was not very great, especially in the region of low Mach number.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.1
• /
• pp.16-25
• /
• 2014

The system analysis and design program of the liquid rocket engine has been developed for preliminary conceptual design process. The program consists of modular programs analyzing the main thruster, the gas-generator, turbo-pumps, the turbine, pipes, valves and so on. Each module has been developed in order to estimate performance, weight, and shape parameters of the components. The results of them have been verified with experimental data or other programs.