• 지질공학
• /
• 제23권3호
• /
• pp.283-292
• /
• 2013

석회암 사면에서 터널 출입구를 시공하기 위하여 진입로를 개설하던 중 사면붕괴가 발생되었다. 사면의 붕괴원인을 조사하기 위하여 현장조사, 실내시험 및 수치해석을 수행하였다. 수치해석결과에 따르면 터널 출입구 진입로 개설이전 사면안전율은 1.0이하이며, 진입로 개설이후 사면안전율은 더 저하되는 것으로 나타났다. 그리고 진입로 개설이후 전단변형률 및 소성영역은 사면상부에서 하부로 전이되므로 사면활동영역이 증가되어 사면안정성을 저하시키는 것으로 해석되었다. 터널 출입구 시공을 위해서는 해당사면에 대한 안정성을 확보하여야 하므로, 대상현장의 조건을 고려하여 록볼트, 록앵커 및 FRP 그라우팅을 사면에 보강하는 것으로 결정하였다. 적용된 사면보강공법의 효과를 확인하기 위하여 현장계측을 수행하였다. 현장계측결과 사면지반의 수평변위는 매우 미소하며, 대부분 발생된 이후 다시 회복되는 탄성거동을 보였다. 그리고 록볼트 및 앵커축력은 터널굴착작업 및 장마기간에 의한 영향보다는 사면굴착작업시 영향을 가장 크게 받으며, 터널굴착작업이후 수렴하는 경향을 보이므로 대상사면은 안정한 상태임을 확인할 수 있다.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 추계학술발표대회 논문집
• /
• pp.27-33
• /
• 2011

HCPV(High Concentrated PV) systems have well known for CPV market all over the world. Low concentration type silicon based modules have been introduced in the market. But low cost of standard flat silicon modules made them useless nowadays. High cost of compound semiconductor solar cell reduced cost effective cpv module production than that of recently silicon solar cell. In order to overcome increasing cost of CPV module, we study middle concentration type fresnel lens simulation using concentrated type silicon based solar cell. Linear type fresnel lens made production of CPV module without secondary optics such as light pipe or light tunnel. This type of fresnel lens design makes more cost effective solution for cpv niche market.

• Journal of Biosystems Engineering
• /
• 제24권1호
• /
• pp.19-24
• /
• 1999

Motivated by the need for developing the more efficient lighting system for light culture of strawberries in the greenhouse, this paper aims at acquiring and suggesting more concrete and scientific foundation of illuminating position, numbers of light source by investigating the types of lighting system and illumination distribution in the greenhouse for light culture of strawberries. The results of investigation and experiment are summarized as following below: 1. The types of lighting system used in the greenhouse producing strawberries were classified as 1 line and 2 lines lighting system. 2. As for the arranging types of artificial light, 2 lines lighting system, were classified as Z-type, N-type and W-type. (Refer Fig. 3) 3. The results of illumination distribution for Z-type, N-type and W-type of 2 lines illuminating system in the greenhouse with a small size tunnel measured at the height of 1.5m from the ground with 220V, 100W lamp in 6m light gap showed that maximum illuminance are 961x, 1211x, 1251x, minimum illuminance are 4.41x, 4.71x, average illuminance are 33.71x, 43.11x, 44.51x and standard deviations are 28.31x, 35.41x, 38.31x at each types. 4. Proportion of the area below optimal illuminance to floor area at the two lines illuminating system of Z-, N-, and W-type in greenhouse were appeared as 39.4%, 26.0% and 26.3%, respectively. Also proportion of the area over optimal illuminance to floor area at the two lines illuminating system of Z-, N-, W-type in greenhouse were appeared as 16.8%, 14% and 14.7%, respectively. Thus N-type was superior to the others from the view points of optimal illumination distribution and energy saving.

• 터널과지하공간
• /
• 제19권1호
• /
• pp.1-10
• /
• 2009

암반 내 구조물을 시공하는 경우 역학적 안정성을 평가하기 위하여 암반의 특성을 조사한다. 이 경우 암반의 특성은 주로 암반 내 절리의 특성에 의하여 좌우된다. 지금까지는 암반 내 절리의 특성을 조사하기 위하여 암반이 노출된 사면이나 노두에 접근하고 육안으로 직접 관찰하였다. 이때 급사면과 같은 곳에서 접근의 문제, 작업의 안전 문제, 많은 시판이 걸리는 문제, 조사시간에 비하여 얻은 정보량의 부족, 정보의 재현 문제, 측정 오차 문제 등의 제한이 있었다. 따라서 이와 같은 문제를 개선하기 위하여 LIDAR (light detection and ranging)로 암반을 스캔하여 얻은 포인트 클라우드(point cloud)글 Split-FX 소프트웨어로 처리한 결과 절기의 방향과 간격 및 절리면의 거칠기 등 절리의 특성을 정확하고 효율적으로 분석할 수 있었다.

• 한국지반공학회논문집
• /
• 제27권12호
• /
• pp.53-68
• /
• 2011

본 연구에서는 기존 NATM 터널공법의 문제점을 개선한 신개념의 NATM Composite 라이닝 공법 개발에 대한 기초 연구를 수행하였다. 먼저 NATM Composite 라이닝 공법의 개요 대하여 소개하고 시공성에 대한 검토를 수행하였다. 그리고 NATM Composite 라이닝 공법의 개발을 위한 기초 연구로서 고성능 PC 패널 라이닝의 개발을 위해 다양한 혼화재료의 영향을 검토하고, PC 패널 설치 위치별 최적 배합을 도출하였다. 또한 PC 패널 배면 뒤채움재로 경량기포 모르타르 재료를 개발하였으며 실대형 하중재하 실험을 통해 NATM Composite 라이닝 공법의 거동 특성을 규명하였다. NATM Composite 라이닝 공법은 기존 현장타설 라이닝 공법에 비해 안정성과 시공성을 크게 향상 시킬 수 있을 것으로 판단된다.

• 한국전기전자재료학회논문지
• /
• 제27권8호
• /
• pp.541-546
• /
• 2014

Korea Expressway Corporation established standard of LED lighting fixture in Dec. 2013. To raise compatibility, the standard requires a fixed form and it is applied to street lights and tunnel lights, etc. Because streetlight has different circumstance condition from tunnel light that is down light and exposed to constant wind velocity over height of 8 meters, in case of LED module which has the same shape, characteristic of radiant heat can be different. In this paper, we designed 25 [W] LED Module that is designated by standard of Korea Expressway Corporation and analyzed characteristics of radiant heat about natural convection and forced convection. It is dropped 10.12[$^{\circ}C$] that max temperature is decreased by increasing 20 mm of bended height of heatsink at the condition of natural convection. Radiant heat characteristic of bended height 35 mm became 78.08[$^{\circ}C$] at the condition of natural convection, 55.30[$^{\circ}C$] at the condition of forced convection so that 22.78[$^{\circ}C$] is decreased that is 29.1[%] decrease. Bended height 55mm became 67.96[$^{\circ}C$] at the condition of natural convection, 48.04[$^{\circ}C$] at the condition of forced convection so that 19.92[$^{\circ}C$] is decreased that is 29.3% decrease.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 E
• /
• pp.1779-1781
• /
• 1997

The 2.0 GeV Pohang Light Source (PLS) is consisted of a full energy Linac and a storage ring. Four kicker magnets are installed in the storage ring tunnel to move the stored beam orbit in the storage ring closer to the injected beam from the beam transfer line. The injected beam then falls into the storage ring beam dynamic aperture. A kicker magnet modulator drives all four kicker magnets to maintain field balance and also synchronized kick of the beam. The kicker modulator can handle 2 GeV full energy beam. The kicker magnet modulator is installed in the storage ring tunnel and under stable operation. Specification of the kicker magnet modulator is ${\sim}6.0{\mu}s$ pulse-width, 200 ns flat-top width with ${\pm}0.2%$ regulation, ${\sim}24\;kA$ peak current, and 10 Hz repetition rate. Two thyratron switches (EEV CX-1536AX) are used in the system. In this article, design, and experimental results of the kicker magnet modulator are discussed.

• Wind and Structures
• /
• 제20권5호
• /
• pp.683-699
• /
• 2015

Lighting poles and antenna masts are typically high, slender and light structures. Moreover, they are often characterized by distributed eccentricities that make very complex their shape. Experience teaches that this structural type frequently suffers severe damage and even collapses due to wind actions. To understand and interpret the aerodynamic and aeroelastic behavior of lighting poles and antenna masts, this paper presents the results of static and aeroelastic wind tunnel tests carried out on a complex prismatic element representing a segment of the shaft of such structures. Static tests are aimed at determining the aerodynamic coefficients and the Strouhal number of the test element cross-section; the former are used to evaluate the critical conditions for galloping occurrence based on quasi-steady theory; the latter provides the critical conditions for vortex-induced vibrations. Aeroelastic tests are aimed at reproducing the real behavior of the test element and at verifying the validity and reliability of quasi-steady theory. The galloping hysteresis phenomenon is identified through aeroelastic experiments conducted on increasing and decreasing the mean wind velocity.

• 한국농공학회논문집
• /
• 제55권6호
• /
• pp.31-35
• /
• 2013

This study was carried out to present the pressure drop for various wind speeds through nine types of screens used in horticultural facilities. The screens have been widely used to prevent harmful insects from being entered into agricultural facilities, to reduce strong wind and to shade a light as well. Whatever the usage of the screens was, it was necessary to have good knowledge of how much the screen caused a pressure drop for wind speeds when analyzing both the inner thermal-flow distribution in the facility and the effect of reducing wind speed by using CFD. Furthermore, as for wind screens, the pressure drop for wind speeds was needed as a design load in evaluating the structural stability of the structures supporting the screens. Therefore, the pressure drop through the screens for wind speeds of 5~30 $m{\cdot}s^{-1}$ at about 5 $m{\cdot}s^{-1}$ interval and inflow angles of $0{\sim}45^{\circ}$ at an interval of $15^{\circ}$ was respectively measured in a subsonic wind tunnel. The relation of the pressure drop for various screens was well fitted as a secondorder polynomial expression.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.151-156
• /
• 2008

The after 1974 capital region electric railroad is opened to traffic Koraill and Seoul metro adopt each other different power supply method and they operate and they are come. AC 25[kv] method voltage the insulation becomes larger standing distance highly, the case tunnel section which will introduce in the underground segment becomes on a large scale and the cost of construction increases to the city center and the underground segment adoption of DC method was many. To recent times with R-bar (Rigid-bar) introductions change of tunnel section the introduction of AC method came to be easy without in the underground segment. Operates sees in the electric protection where the Seoul metro and the Korail are different each other and, from the dead section segment the interior electric light to put out lights the passenger brings about inconveniently and the civil appeal which demands a power supply method unification occurs, within the company interchange electric railroad brazier safety improvement and maintenance expense curtailment etc. the flaw is original proposal, is a condition which finishes a feasibility study service about the power supply method fringe land. Interchange analysis of the DC electric railway it leads from the present paper and it compares under analyzing being it could be reflected to also the route which is in the process of actual using boil the strong point and a weak point of DC and AC method of the establishment route constructive at the time of and