• 한국철도학회논문집
• /
• 제8권6호
• /
• pp.513-519
• /
• 2005

The Korean Tilting Train eXpress may produced a strong micro-pressure wave in tunnel exit because of large train/tunnel area ration of conventional railways. This micro-pressure wave causes an impulsive noise which is a serious environmental noise pollution near tunnel exit. Tunnel hood can be the method of reducing the micro-pressure wave in tunnel exit. Therefore, parametric studies for tunnel hood are performed with respect to the hood length and size to investigate the effects of the tunnel hood. Also, axi-symmetric unsteady compressible flow solver was used to analyze train-tunnel relative motion. According to the result of numerical analysis, the maximum micro-pressure wave in tunnel exit is reduced by 56% throughout the hood establishment on conventional railways.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.65-68
• /
• 2006

Experiments were performed to investigate the effects of mud-flap width on the aeroacoustic noise generation inside high-speed trains. The open-circuit type wind tunnel was used. The measurement setup was custom-built to simulate intercoach spacing. From the measurements, the characteristics of the turbulent flow after the intercoach spacing and consequent generation of aeroacoustic noise inside the cabin was investigated. Especially the effects of mud flap length on the characteristics of the characteristics of the turbulent flow were identified. The mechanism of noise generation by analyzed interactions with structure vibration characteristics and generation characteristics of blocked pressure was investigated.

• 대한기계학회논문집B
• /
• 제23권1호
• /
• pp.58-68
• /
• 1999

The entry compression wave, which forms at the entrance of a high-speed railway tunnel, is closely related to the pressure transients in the train/tunnel systems as well as an impulsive noise appearing at the exit of the tunnel. In order to alleviate such undesirable phenomena, some control strategies have been applied to the compression wave propagating inside the tunnel. The objective of the current work is to investigate the effect of tunnel entrance hoods on the entry compression wave at the vicinity of the tunnel entrance. Three types of entrance hoods were tested by the numerical method using the characteristics of method for a wide range of train speeds. The results show that the maximum pressure gradient of compression wave can be considerably reduced by the tunnel entrance hood. Optimum hood shape necessary to reduce the pressure transients and impulsive noise was found to be of an abrupt type hood with its cross-sectional area 2.5 times the tunnel area. It is believed that the current results are highly useful in predicting the effects of entrance hoods and in choosing the shape of proper hood.

• 한국가시화정보학회지
• /
• 제16권3호
• /
• pp.8-15
• /
• 2018

Recently, as the high speed railway becomes more common, new environmental problems such as noise around tunnels are appearing. When a high speed train enters a tunnel, a compression wave in the tunnel is generated and propagated toward the tunnel exit at a sonic speed. When it reaches the tunnel exit, a part of compression wave radiates as a pulse typed impulse wave to the outside of tunnel. The impulse wave has an explosive noise. When the impulse wave is propagated around a village, it induces a serious noise or other problems to the resident. In order to solve these engineering problems, it is important to investigate the radiation characteristics of the impulse wave radiated from the tunnel exit. In this study, the effect of the length and angle of the baffle plate at the tunnel exit on the impulse wave radiated from the tunnel exit was investigated by numerical analysis. As a results, the baffle plate greatly affected the propagation of impulse wave.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.843-848
• /
• 2001

Railroad noise is one of the main causes of environmental impact. Whenever a new railroad line is planned or a housing project near an existing railroad is proposed, an estimate of the relevant noise levels is usually required. For this, it is necessary to quantify those parameters that affect the railroad noise. This paper deals with an estimation of railroad noise using soundproof tunnel in a high-rise apartment building

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 춘계학술대회 논문집
• /
• pp.128-134
• /
• 2014

A Experimental study on frequency characteristics of the microphone array covered with Kevlar in closed test section wind tunnel. Microphones that are flush mounted in a closed test section wall of wind tunnel are subject to very high flow noise resulting from the turbulence in the wall boundary layer. At this time the microphones measure the strong hydrodynamic fluctuations generated by the flow. The phenomena are referred to a microphone self-noise and a method for reducing this has studied. In this paper the array that covered with acoustically transparent Kevlar sheet was designed and made to reduce the flow-induced self-noise. For the validation frequency characteristics of the Kevlar, the microphone array was installed on the wall and test was performed for white noise and sine wave of several frequencies using loudspeaker. In addition, the paper compared the signals as a tension of Kevlar. The results were presented that tend to decrease the sound pressure level at high frequency above 3500Hz according to existence of Kevlar.

• 한국소음진동공학회논문집
• /
• 제23권9호
• /
• pp.831-840
• /
• 2013

The noise levels of workers in tunnel sites are likely to be high because tunneling work places are confined space. However, research on the noise exposure levels of tunneling workers have not been performed intensively due to restricted accessibility to tunnel construction sites. The aim of this study is to evaluate the noise exposure levels for workers engaged in tunneling work sites. Noise dosimeters were used for monitoring workers' noise exposure level in 5 tunneling work sites in accordance with the Notification of the Ministry of Labor. Among 5 tunneling work sites, 4 of them used NATM tunneling method and 1 work site used shield TBM tunneling method. The average noise exposure levels of NATM tunneling workers was 81.1 dB(A) and 15.4 % of the workers' noise level were exposed more than 90 dB(A) which is the exposure limit value. In Shield TBM tunneling method, 4.3 % of the workers were exposed more than 90 dB(A) of noise level, the average noise exposure levels of TBM tunneling workers was 84.1 dB(A).

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.1026-1031
• /
• 2003

Numbers of people living in high rise apartments are growing due to the overcrowding in urban area. Acoustic environment in those residential buildings has been seriously deteriorated by the increase of wheeled transports. Commonly used sound barriers have a limitation in controlling noise influencing higher part of a residential building. The use of noise barrier tunnels can be an alternative to supplement the defects of conventional noise barriers. But intensive measurements on noise levels at apartments vicinity of current noise barrier tunnels show that the tunnel now has a limited advantage on reducing the noise levels from arterial roads. The present work aims at providing an useful design tool In designing noise barrier tunnels for residential areas adjacent to roads. Number of field measurements, scale model measurements, and computer simulations were performed to ensure whether the prediction from scale model and computer simulation are appropriate. Result shows that the predictions from scale models and computer simulations could be valid prediction tools for designing sound barrier tunnels.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 춘계학술대회 논문집
• /
• pp.785-786
• /
• 2011

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1999년도 춘계학술대회 논문집
• /
• pp.406-413
• /
• 1999

A compression wave is generated by the high speed train which enters a tunnel, and it propagates along the tunnel. When the compression wave emerges from the exit of the tunnel, it causes an impulsive noise, and the strength of the impulsive noise depends on the pressure gradient of the first compression wave. So it needs to reduce the pressure gradient for the minimization of impulsive noise. The entrance hood is used for the reduction of the pressure gradient. In the present study, the pressure transients were numerically calculated for three shapes of hood, In order to validate the numerical simulation, the pressure and pressure gradient were compared with the experimental data of moving model rig. The calculation results won well agreed with the experimental data, and also showed that the hood had an effect on the pressure gradient of the tunnel inside.