• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1999.05a
• /
• pp.348-354
• /
• 1999

In recent years, a PID controller has been used as a major control method in real control processes. This controller requires a determination of PID control gains. But it is difficult to select the best gains theoretically. Thus there have been many approaches to determine them empirically Most of them are based on experience and knowledge. In this paper, we proposed a tuning method of the PID Parameters by using neural network. To show effectiveness of the proposed method, the simulation of DC motor and one link manipulator position control is carried out.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2179-2181
• /
• 2004

Model-free Method들 중에 반복 피트백 조절 알고리즘(Iterative Feedback Tuning, IFT)는 특정한 성능지수를 정의하고, 이를 최소화하도록 제어기의 게인들을 조절하는 방법을 제시하였다. PID와 같은 고전적인 제어이론에 근거한 제어기 설계 과정과는 달리, IFT 알고리즘은 반복 실험을 통해 성능지수의 Gradient를 구하여 이로부터 필터 게인들 조정하는 방법을 채택하고 있다. 수학적 증명과 실험적 실증을 통하여 IFT의 수렴성과 유용성이 보여짐에도 불구하고 IFT 알고리즘의 한계점은 단일 성능지수의 사용이라는데 있다. 이를 개선하기 위해서는 단일 제어 목적을 위한 단일 성능지수의 사용이 아닌 복수의 제어 목적을 위한 복수의 성능지수의 사용이 필요하다. 본 논문에서는 두 개의 성능지수를 가지는 IFT를 이용해서 위상 여유가 크고, 대역폭이 넓은 제어기를 설계하기 위해서 제어기 게인을 자동 조절하는 알고리즘을 제안하고 ODD에서 사용되는 플랜트에 적용한 모의실험을 통하여 그 유용성을 보였다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.54-61
• /
• 2007

A variable gain low noise amplifier (VG-LNA) implemented in TSMC 0.18 um process is presented. This VG-LNA is designed of two stage amplifier, and its gain is controlled by the shunt feedback loop composed of a gain control transistor (GCT) and a coupling capacitor in second stage. The channel resistance of GCT in the shunt feedback loop influences the input and output stages of a second stage by the Miller effect. Total gain of the proposed VG-LNA is changed by two factors, the load impedance reduction and the interstage mismatch by controlling the channel resistance of the GCT. Consequently, by adding a shunt feedback with a gain control transistor, this proposed VG-LNA achieves both wide gain tuning range of 37 dB and continuous gain control simultaneously.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.251-259
• /
• 2016

This paper describes that how to enhance the robustness of semiconductor TRM(Transmitter and Receiver Module) through the bias sequencing and tuning the switching time. Previous circuit designs focused on improving the MDS(Minimum Detection Signal) performance. Because TRM has critical problem which transmission output signal leak into receiver by it's compact design. Under this condition, TRM was frequently broken down within the MTBF(Mean Time Between Failure). This study proposes the bias sequencing and tuning the switching time to improve above problem. At first, we collected major failure symptom and infer it's cause. Second, we demonstrated it's effect by derive the improvement method and apply it to our system. And finally we can convinced that the proposed method clear the frequent failure problem with its lack of isolation.

• Smart Structures and Systems
• /
• v.13 no.2
• /
• pp.219-233
• /
• 2014

In a companion paper, Pasala and Nagarajaiah analytically and experimentally validate the Adaptive Length Pendulum Smart Tuned Mass Damper (ALP-STMD) on a primary structure (2 story steel structure) whose frequencies are time invariant (Pasala and Nagarajaiah 2012). In this paper, the ALP-STMD effectiveness on a primary structure whose frequencies are time varying is studied experimentally. This study experimentally validates the ability of an ALP-STMD to adequately control a structural system in the presence of real time changes in primary stiffness that are detected by a real time observer based system identification. The experiments implement the newly developed Adaptive Length Pendulum Smart Tuned Mass Damper (ALP-STMD) which was first introduced and developed by Nagarajaiah (2009), Nagarajaiah and Pasala (2010) and Nagarajaiah et al. (2010). The ALP-STMD employs a mass pendulum of variable length which can be tuned in real time to the parameters of the system using sensor feedback. The tuning action is made possible by applying a current to a shape memory alloy wire changing the effective length that supports the damper mass assembly in real time. Once a stiffness change in the structural system is detected by an open loop observer, the ALP-STMD is re-tuned to the modified system parameters which successfully reduce the response of the primary system. Significant performance improvement is illustrated for the stiffness modified system, which undergoes the re-tuning adaptation, when compared to the stiffness modified system without adaptive re-tuning.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.961-966
• /
• 2009

This paper presents precise temperature control of oil outlet in an oil cooler with hot-gas bypass control as an industrial refrigerator. The control system was designed for obtaining precise temperature control performance even though abrupt disturbances based on flow rate control of hot-gas bypass. PID controller was adopted in feedback control system. We showed that the gain of PID could be easily determined by using gain-tuning methods without any numerical model. Through some experiments, excellent control performances such as overshoot within 1.7%, steady state temperature error within ${\pm}0.1^{\circ}C$ were established by a simple PI controller. We expect that the system can control the target temperature within error of $0.33^{\circ}C$ under abrupt disturbances.

• Journal of Power Electronics
• /
• v.17 no.4
• /
• pp.1058-1070
• /
• 2017

This paper proposes a novel active damping scheme to suppress LCL-filter resonance with only grid-current feedback control in grid-connected voltage-source converters. The idea comes from the concept of the model reference adaptive control (MRAC). A detailed theoretical derivation is given, and the effectiveness of this method is explained based on its physical nature. According to the control structure of this method, the active damping compensator, which is essentially a second order resonant integrator (SORI) filter, provides an effective solution to damp LCL resonance and to eliminate the need for additional sensors. Compared with extra feedback methods, the cost and complexity are reduced. A straightforward tuning procedure for the active damping method has been presented. A stability analysis is illustrated in the discrete domain while considering a one-step delay. Finally, experimental results are presented to validate the analysis and to demonstrate the good performance of the proposed method.

• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.561-563
• /
• 1999

The looper of a hot strip finishing mill is installed between each pair of stands and plays a key role to enhance the product quality of strip by controlling the tension and height of strip in each inter-stand. Though the conventional looper control has achieved the mass products of strip so far, it has difficulties not only tuning gains by means of errors which are caused by coupling effects between strip tension and looper angle both utilizing tension feedback. Therefore, the non-interactive control employing cross controller and tension feedback has been introduced in looper control system in order to overcome the coupling effects existing between tension and looper angle and track the reference tension efficiently. In this paper, we present the cross controllers which play a role to decouple reciprocal effects between tension and looper angle and show better performance.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.3
• /
• pp.17-24
• /
• 2004

We present a P-type iterative learning control(ILC) scheme for uncertain robotic systems that perform the same tasks repetitively. The proposed ILC scheme comprises a linear feedback controller consisting of position error, and a feedforward and feedback teaming controller updated by current velocity error. As the learning iteration proceeds, the joint position and velocity mrs converge uniformly to zero. By adopting the learning gain dependent on the iteration number, we present joint position and velocity error bounds which converge at the arbitrarily tuned rate, and the joint position and velocity errors converge to zero in the iteration domain within the adopted error bounds. In contrast to other existing P-type ILC schemes, the proposed ILC scheme enables analysis and tuning of the convergence rate in the iteration domain by designing properly the learning gain.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.719-720
• /
• 2006

In the mechanical system, optimization of motion control is very essential in the aspect of automation technique progress. In the servo system, the function of controller is very important but most of the controllers have played only the role of pulse generator because the controller with main function is very expensive. In this thesis, the system was composed of PC, commonly used driver AC servo motor and a produced control board. The PC transmit a gain, a locus data to a driver and controller. At the same time, it converts imformation from the controller and convert them into data and offer an output with graph. The role of a controller is to trasmit a locus data to a driver and counting the pulse on the phase of an encoder to the PC. We have performed the experiment in order to confirm with variable PID parameter capable of the optimization of gain tuning with the counting of feedback control sensor signal with regard to the external interface into the system, such as torque. Based on the experiment result, we have confirmed as follows: First, it was confirmed that we could easily input control factors P.I Gain, constant $K_P,\;K_I$ into PC. Second, not only pulse generator function was possible, but with this pulse it was also possible to count using software with PIC chip. And third, using the multi-purpose PIC micro chip, simple operation and the formation of small size AC Servo Controller was possible.