• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.197-197
• /
• 2011

In this study, in contrast with cases in which Scanning Tunneling Microscopy (STM) tip-induced reactions were instigated by the tunneling electrons, the local electric field, or the mechanical force between a tip and a surface, we found that the tungsten oxide (WO3) covered tungsten (W) tip of a STM acted as a chemical catalyst for the S-H dissociative adsorption of phenylthiol and 1-octanethiol onto a Ge(100) surface. By varying the distance between the tip and the surface, the degree of the tip-catalyzed adsorption could be controlled. We have found that the thiol head-group is the critical functional group for this catalysis and the catalytic material is the WO3 layer of the tip. After removing the WO3 layer by field emission treatment, the catalytic activity of the tip has been lost. 3-mercapto isobutyric acid is a chiral bi-functional molecule which has two functional groups, carboxylic acid group and thiol group, at each end. 3-Mercapto Isobutyric Acid adsorbs at Ge(100) surface only through carboxylic acid group at room temperature and this adsorption was enhanced by the tunneling electrons between a STM tip and the surface. Using this enhancement, it is possible to make thiol group-terminated surface where we desire. On the other hand, surprisingly, the WO3 covered W tip of STM was found to act as a chemical catalyst to catalyze the adsorption of 3-mercapto isobutyric acid through thiol group at Ge(100) surface. Using this catalysis, it is possible to make carboxylic acid group-terminated surface where we want. This functional group-selective adsorption of bi-functional molecule using the catalysis may be used in positive lithographic methods to produce semiconductor substrate which is terminated by desired functional groups.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1888-1891
• /
• 2003

In this paper, we proposed a new method to control the length of carbon nano tube in the single CNT probe. A single CNT probe was composed of a tungsten tip made by the electrochemical etching and carbon nano tube which was grown by CVD and prepared through the sonication. The two components were attached with the carbon tape. Since the length of CNT can not be controlled during the manufacturing, the post process is needed to shorten the CNT. In this paper, we proposed the method of electrochemical process. The process was done under the optical microscope and the results were checked by SEM. The diameter of the carbon nano tube used in this paper was about 130nm because the above process had to be done with the optical microscope. Using the method proposed in this paper, we can control the length of the nano tube tip.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.245-249
• /
• 2002

Tungsten carbide microshaft is used as various micro-tools in MEMS because it has high hardness and good rigidity. In this study, experiments were performed to produce tungsten carbide microshaft using electrochemical machining. $H_2SO_4$solution was used as electrolyte because it can dissolve tungsten and cobalt simultaneously. Optimal electrolyte concentration and machining voltage satisfying uniform shape and large MRR of workpiece were found. For one-step machining, the immersion depth over 1 mm was selected for avoidance of concentration of electric charge at the tip of the microshaft. The limit diameter with good straightness was shown and an empirical formula for WC-microshaft machining was suggested. By controlling the various machining parameters, a straight microshaft with 30 $\mu\textrm{m}$ diameter, over 1 mm length and under 0.5$^{\circ}$ taper angle was obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.6
• /
• pp.167-171
• /
• 2004

In this paper, we proposed a new method to control the length of carbon nanotube using electrochemical etching. We made a nano probe that was composed of the tungsten tip and multi-wall carbon nanotube. The nano probe was placed on the nano stage and the carbon nanotube on the nano probe was etched in the electrolyte solution with the applied voltage. The overall procedures were done under optical microscope and can be monitored. We can obtain a nano probe with proper length through this procedure.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.3
• /
• pp.891-894
• /
• 2014

The ultrashort electron pulse, laser-emitted from the metal tip apex has been characterized and used as a probing source for a new electron microscope to visualize the morphology of the gold-mesh in the nanometric resolution. As the gap between the tungsten tip and Au-surface is approached within a few nm, the large electromagnetic field enhancement for the incident P-polarized laser pulse with respect to the tip-sample axis is strongly observed. Here, we demonstrate that the time-resolved tip-enhanced electron emission microscope (TEEM) can be implemented on the laboratory table top to give the two-dimensional image, opening lots of challenges and opportunities in the near future.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2009.08a
• /
• pp.329-329
• /
• 2009

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.315-318
• /
• 2004

The Advantages of hot machining are the reduction of cutting forces, tool wear, and the increase of material removal rates. In this study, a hot-machining characteristics of milling by CBN tip was exprimentely analyzed, and the influence of the surface temperature and the depth of cut on the tool life were investigated. The selection of a heating method for obtaining ideal temperature of metals in machining is important. Faulty heating methods could induce unwanted structural changes in the workpiece and increase the cost. This study uses gas flame heating. It is obtained that tungsten carbide-alloyed has a recrystallisation temperature range of $800-1000^{\circ}C$ which is the high heating temperature that might induce unwanted structural changes. If it is performed at temperatures higher than $800^{\circ}C$ in machining, the possibility of unwanted structural changes and the increased wear of tool can be shown. Consequently, in hot machining of tungsten carbide-alloy, this study has chosen $400^{\circ}C-600^{\circ}C$ because the heating temperature might be appropriate in view of the cost and workpiece considerations. The results of this study experimentally shows a new machining method for tungsten carbide-alloyed that decreases the wear rate of machining tools

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.365-369
• /
• 2004

The Advantages of hot machining are the reduction of cutting forces, tool wear, and the increase of material removal rates. In this study, a hot-machining using gas flame heating characteristics of milling by CBN tip was analyzed, and the influence of the surface temperature and the depth of cut on the tool life were investigated. The results show that hot machining of tungsten carbide-alloyed is more effective than conventional machining. In addition, some advantages obtained from hot machining, such as decrease of tool wear and cutting force, high surface quality.

• Applied Microscopy
• /
• v.46 no.3
• /
• pp.155-159
• /
• 2016

This paper analyses the relationship between the distribution of a dielectric layer on the apex of a metal field electron emitter and the distribution of electron emission. Emitters were prepared by coating a tungsten emitter with a layer of epoxylite resin. A high-resolution scanning electron microscope was used to monitor the emitter profile and measure the coating thickness. Field electron microscope studies of the emission current distribution from these composite emitters (Tungsten-Clark Electromedical Instruments Epoxylite resin [Tungsten/CEI-resin emitter]) have been carried out. Two forms of image have been observed: bright single-spot images, thought to be associated with a smooth substrate and a uniform dielectric layer; and multi-spot images, though to be associated with irregularity in the substrate or the dielectric layer.

• Tribology and Lubricants
• /
• v.17 no.3
• /
• pp.191-197
• /
• 2001

Nano adhesion and friction characteristics between SPM(scanning electron microscope) tips and flat plates of different materials were experimentally studied. Tests were performed to measure adhesion and friction in AFM(atomic force microscope) and LFM(lateral force microscope) modes in different conditions of relative humidity. Three different Si$_3$N$_4$ tips (rdaii : 15nm, 22nm and 50 nm) and three different flat plates of Si-wafer(100), W-DLC(tungsten-incorporated diamond-like carbon) and DLC were used. Results generally showed that adhesion and friction increased with the tip radius, and W-DLC and DLC surfaces were superior to Si-wafer. But the adhesion force of Si-wafer showed non linearity with the tip radius while W-DLC and DLC surfaces showed good correlation to the “JKR model”. It was found that high adhesion force between Si-wafer and a large radius of tip was caused by a capillary action due to the condensed water.