• 태양에너지
• /
• 제10권1호
• /
• pp.5-13
• /
• 1990

온도가 일정한 외벽을 열원으로 하는 수직원통형 축열조 내에 채워진 상변화물질의 내향용융 과정에서 자연대류에 의한 열전달현상을 유한차분법을 이용하여 수치해석하였고, 그 결과를 실험을 통하여 검증하였다. 상변화물질로는 용융점온포가 $42.5%^{\circ}C$ n-docosane paraffin($C_{22}H_{46}$)을 사용하였다. 본 연구 결과에서 상변화물질의 용융속도는 액상영역의 자연대류로 인하여 축열조 상부로 갈수록 빠른 것으로 나타났다. 그리고 상변화물질의 초기온도는 액상영역 속도분포에 큰 영향을 주지 않으며, 상변화물질의 초기온도가 낮을수록 용융속도는 늦어지고 축열조의 형상비($H/r_w$)가 커질수록 자연대류는 활발해지는 것으로 나타났다. 이러한 수치해석의 결과는 실험 결과와 잘 일치하였으나, 수치해석시 상변화물질의 용융에 따르는 체적팽창을 고려하지 않았기 때문에 용융이 진행 됨에 따라 오차가 발생하였다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제10권1호
• /
• pp.75-83
• /
• 1987

The insulating oil used for X-ray tube housing were degraded by X-ray irrdiation, high temperature and high anode voltage for normal operation. This study was measured the conduction current-X-ray dose, heating degradation, time, temperature and electric field characteristics and the dependense of electrode materials and gap length in the X-ray irradiatied insulating oil under of D.C voltage. The obtained results can be summarized as following. 1. The conduction current of X-ray irradiated insulating oil is more about $2.5{\sim}3$ times as large as than that of non x-ray irradiated, and is become saturation phenomena after some degree. 2. The conduction current of many times heating x-ray irradiated insulating oil is more than that of a few times heating. 3. The higher temperature x-ray irradiated insulating oil is increased, the more conduction current, and that is increased about ten times as large as when it's temperatures is increased to $80^{\circ}C\;at\;30^{\circ}C$, twenty five times at $100^{\circ}C$. 4. The dependence of electrode materials is appeared at the low electric field, and the small gap length with Fe > Cu > Al. 5. The low electric field than 3000 v/cm is appeared Ohm's law region, and the high is become saturation region at the I-E characteristics. 6. The larger gap length is become, the more conduction current is increased at the same electric field.

• 한국조명전기설비학회지:조명전기설비
• /
• 제5권4호
• /
• pp.35-42
• /
• 1991

Recently, HID lamps have been considered as important in regard to the trend of energy saving, and increasingly and diversely used in various ways. This paper will show the simulating models concerning high-pressure arc discharge system directly applicable for its design and manufacture, and analyze its various characteristics. For warm-up characteristics, the evaporating process of inner atoms is described in terms of second-order differential equation: for the thermal conduction from are axis to discharge wall and outer bulb, its transfer process is introduced according to five first-order differential equations. Under the steady state satisfying LTE, the time-variant characteristics are suggested by means of time-dependent energy balance equation derived from fluid equations, approximation of radiation energy and material functions in the discharge tube. The simulating models concerning these equations are then applied for high-pressure mercury lamp.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권5호
• /
• pp.190-197
• /
• 2005

A reliable and compact pulse power supply using a thyratron and a magnetic pulse compression (MPC) circuit was developed for a metal vapor laser. The life time of the pulse power supply is expected to be much longer than that of a conventional thyratron-discharge type pulse power supply. A thyratron generated a long pulse of its conduction pulse width 500 ns and then it was compressed to less than 80 ns of its output voltage rise time by a three stage MPC circuit. This pulse power supply was applied to a laser plasma tube of 30 mm inner diameter and 1.5 m discharge length. It was operated several hundreds hours without any troubles.

• 대한기계학회논문집
• /
• 제14권6호
• /
• pp.1621-1628
• /
• 1990

본 연구에서는 많은 실질적인 시스템에서, 많은 양의 복합된 전도, 대류, 복 사의 열전달 현상이 동시에 일어나기 때문에 복합된 열전달 모드가 다같이 다루어져야 만 한다. Fig.1에서 보는 바와 같이 얇은 원형휜이 튜브 주위에 무수히 부착되어 있 으며, 휜과 튜브주위를 기체가 흐르고 있다. 휜과 휜, 휜과 튜브표면, 휜과 주위환 경, 튜브표면과 주위환경 사이에서 복사 열전달 상호교환이 충분히 다루어졌다. 전 도, 대류, 복사기 동시에 일어나는 열전달 방정식은 비선형 적분-미분 방정식(nonlin- ear integro-differential equation)으로 표현된다. 온도 분포도(temperature dist- ributions), 열전달량(heat transfer rates), 휜효율(fin efficiencies), 휜유효성(f- ineffectivenesses)등이 계산되어졌고, 무차원 형태로 도표에 결과들을 제시하였다.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1301-1309
• /
• 1994

A study of heat transfer and thermophoretic particle deposition has been carried out for the Modified Chemical Vapor Deposition(MCVD) process. A new concept utilizing two torches is suggested to simulate the heating effects from repeated traversing torches. Calculation results for the wall temperatures and deposition efficiency are in good agreement with experimental data. The effects of variable properties are included and heat flux boundary condition is used to simulate the moving torch heating. A conjugate heat transfer which includes heat conduction through solid layer and heat teansfer in a gas in a tube is analyzed. Of particular interests are the effects of torch speeds and solid layer thicknesses on the deposition efficiency, rate and the tapered entry length.

• 설비공학논문집
• /
• 제17권2호
• /
• pp.101-109
• /
• 2005

The purpose of this study is to investigate the performance of outdoor heat exchanger for heat pump using carbon dioxide. Two types of fin and tube heat exchangers (2 rows for type A and 3 rows for B) are tested. Both heat exchangers have counter-cross flow and 1-circuit arrangement. Test results such as heat transfer rate, pressure drop characteristics and temperature distribution in the heat exchanger are shown with respect to mass flow rate of refrigerant and frontal air velocity For cooling mode, the minimum temperature difference between air and refrigerant of type B is smaller than that of type A by $1^{circ}C$, but the pressure loss of air side is much higher for type B by $29\%$. It is found that a large temperature gradient of carbon dioxide during gas cooling Process Promotes thermal conduction through tube wall and fins which results in degradation of heat transfer performance. For heating mode operation, type B heat exchanger shows higher heat transfer performance compared to type A. However, because pressure loss of refrigerant side of type B is much greater than that of type A, the refrigerant outlet pressure of type B becomes lower than that of type A.

• 한국전기전자재료학회논문지
• /
• 제23권4호
• /
• pp.338-342
• /
• 2010

Carbon nanotubes (CNTs) have excellent electrical, chemical stability, mechanical and thermal properties. The MWCNT films were investigated as a transparent electrode for the solar cell, OLED, and field-emission display. MWCNT films were fabricated by air spray method, whose process is quite low-costed, using the multi-walled CNTs solution on glass substrates. Moreover, the most stable film was fabricated when the spraying time was 60 sec. The film that was sprayed with the MWCNT dispersion for 60 sec, has 300nm thick. And its electric resistivity, transmittance rate, mobility and carrier concentration are $6{\times}10^{-2}{\Omega}{\cdot}cm$, 50% at ${\lambda}=550mm$, $4.3{\times}10^{-2}cm^2/V{\cdot}s$ and $2.1{\times}10^{21}cm^{-3}$, respectively. Also, absorption energy of MWCNT films show from 3.9 eV to 4.6 eV. Furthermore, we can use MWCNT films fabricated by the spray method for the transparent electrode.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 춘계학술대회 논문집
• /
• pp.252-255
• /
• 1996

Superconducting current lead is one of the promising applications of the oxide high-Tc superconductors, because they have the advantage of decreasing heat conduction to low temperature region, comparing with a conventional cooper alloy lead. High critical current density is a key factor for the applications such as current lead. (Bi,Pb)$_2$Sr$_2$Ca$_2$Cu$_3$O$\_$x/ high Tc superconductor haute been investigated in terms of critical current density. Bi-2223 superconducting current lead made by CIP and solid state sintering process. Bi-2223 current lead that heat treated at 836$^{\circ}C$ for 240 h in 1/13 P$\_$O$_2$/ had over 150 A/$\textrm{cm}^2$ of critical current density at 77K. We knew that the superconducting properties of tube type current leads were better than rods type of them. And we investigated the relation of Bi-2223 formation and heat treatment condition by XRD and SEM analysis.

• 소성∙가공
• /
• 제24권1호
• /
• pp.13-19
• /
• 2015

For an accurate analysis of hot stamping, a coupled simulation with different aspects of the process(i.e. mechanical, thermal, and phase transformation) is needed. However, coupled simulations are time consuming and costly. Therefore, the current study proposes a simplified method focused on the forming for the hot stamping simulation of a coupled torsion beam axle (CTBA) tubular beam. In this simplified method, non-isothermal conditions were assumed and only conduction was considered, since it represents the majority of the heat transfer during hot stamping. In addition, temperature and strain rate effects were also included. Moreover, an isothermal simulation was conducted and compared with a non-isothermal simulation. Finally, the simulations were verified by experiments. In conclusion, the proposed method is shown to be effective for the development of tube-type parts, and it effectively predicts the deformation of the tubular beam during hot stamping.