• Journal of Welding and Joining
• /
• v.15 no.1
• /
• pp.116-124
• /
• 1997

A scope of this study is to establish the optimum plasma spray conditions for fine ($5\mu\textrm{m}$) $Al_2O_3$ powder. However, the flowability of the $Al_2O_3$ powder is not so good because of irregular particle shape and fine particle size. Therefore, powder feeding system was modified by 1) change of powder feeding line material from polymer to copper 2) shorten the powder feeding tube length 3) heating the powder feeding system to $80^{\circ}C$4) vibrating the powder feeding line continuously, in order to feed the fine powder homogeneously. The homogeneous powder feeding conditions were obtained with the modified powder feeding system by controlling the powder carrier gas flow and the powder flow rate indicator. The best plasma spraying conditions for the fine $Al_2O_3$ powder were found out as 40kw gun power, 80 g/min. powder feed rate and 50 mm working distance after characterizing the microstructure, hardness and wear loss of the $Al_2O_3$ coating layer.

• Child Health Nursing Research
• /
• v.16 no.1
• /
• pp.84-92
• /
• 2010

Purpose: One of the main reasons why mothers quit breast feeding is that the volume of breast milk is inadequate due to insufficiency in suckling. We believe suckling experience may be a factor affecting nipple confusion. So an alternative feeding method, namely cup, spoon, finger, or nasogastric tube feeding may be needed to prevent nipple confusion. The purpose of this study was to construct a predictive model for demand for alternative feeding education by nurses. Methods: A descriptive design with structured self-report questionnaires was used for this study. Data from 175 nurses working in hospitals in Busan were collected between April 1 and 15, 2009. Data were analyzed by decision tree method, one of the data mining techniques using SAS 9.1 and Enterprise Miner 4.3 program. Results: Of the nurses, 81.1% demanded alternative feeding education and 5 factors showed that most of them expressed intention to pay, desire to know about alternative feeding, age, and learning experience. From these results, the derived model is considered appropriative for explaining and predicting demand for alternative feeding education. Conclusion: This confirms that knowledge and compliance in alternative breast feeding for newborn babies should be correct and any inaccuracies or insufficient information should be supplemented.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.306-309
• /
• 2007

In this study, hydroforming characteristic of the double-layered tube was investigated in the hydroforming process. The double-layered tube can be made outer surface on the stainless steel by only one processing. The free bulging test was performed to analysis optimized pressure and axial feeding amount of the double layered tubes. And the experimental results between stainless/carbon and carbon/carbon double-layered tube were compared with the forming data. Moreover analysis model that can be hydroformability and predictable forming pressure of double-layered tube was presented.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.8
• /
• pp.701-706
• /
• 2008

A continuous 3D tube bending machine has been developed for industrial boiler panel production. The machine consists of a main bender, a sub bender, a side bender, tube feeding rollers and control system that includes data management system. Tube position is controlled by a numerical control system. The bending former can be easily replaced according to the shape of bending form. Reduction of working time and improvement of production capacity from the practice have been achieved by bending a long tube in the machine developed.

• Transactions of Materials Processing
• /
• v.10 no.1
• /
• pp.3-14
• /
• 2001

Hydroforming is the technology using hydraulic pressure and forming sheet or tube metals to desired shape in a die cavity. lt can be characterized as tube hydroforming and sheet hydroforming depending on the shape of used blank. Due to its prcess-related benefits, this production technology has been remarkably noticed for great potential for feasible applications and recently gained great attraction from many industrials including automotive and non-automotive. This Paper analyzed the tube and the welded blank hydroforming process and compared formability of the processes for automotive engine mount bracket. The mathematical analysis was performed by using the dynamic explicit finite element code, PAM-STAMP. In tube hydroforming, bending, springback, and forming analysis were carried out and the effect of mandrel and axial feeding were examined. In welded blank hydroforming, pressure curve history is determined and the results of forming analysis were evaluated by the comparison of experimental results in the aspects of deformed shape and thickness distribution.

• Transactions of Materials Processing
• /
• v.11 no.1
• /
• pp.54-60
• /
• 2002

The purpose of the present paper is to investigate the effect of Process parameters such as internal pressure, amount of axial feeding, and frictional condition between the die and the material on the tube hydro-formability. For carbon steel tubes(STKM 12A, STBH 410 and SPS 290), simple bulging, circular bulging and Tee-fitting tests are performed to evaluate the hydro-formability of these materials which is determined by deformation characteristics such as thickness distribution, forming height and branch dome shape. The formabilities obtained from these tests are analysed and compared with the results of the numerical simulation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.145-147
• /
• 2009

The benefits of hydroforming technology are known as weight and cost savings through part consolidation and reduced post-forming processes such as welding and piercing. Hydroforming technology has some weaknesses in terms of process cycle times. But, as the hydraulic system and process designs are continuously developed, the cycle time is also reduced to acceptable and competitive levels. Hot air bulging is one of recently developed hydroforming techniques. Hot air bulging in order to further extend the forming degrees of Al lightweight material is investigated. A heated tube is placed in a heated die and sealed at the ends by sealing cylinders. The tube is subsequently expanded against the die cavity wall by internal pressure provided by air medium. The result of this study shows that axial feeding speed and air pressure have an effect on formability of Al air bulging at elevated temperature.

• Advances in pediatric surgery
• /
• v.2 no.1
• /
• pp.68-71
• /
• 1996

Esophageal atresia(EA) with a double tracheoesophageal fistula(TEF) is rare. It accounts for only 0.7% of all cases of EA and TEF. A male newborn weighing 2860g was born by normal vaginal delivery at 41 weeks' gestation to a 27-year-old mother who had a normal pregnancy. But immediately developed recurrent choking and respiratory distress. Feeding tube was inserted and chest X ray showed the feeding tube coiled in the proximal pouch(T-2 level). With a preoperative diagnosis of EA and distal TEF, the thoracotomy was performed on the third day of life. At thoracotomy, TEF was proved to be a double fistula. Both fistulas were divided and an esophageal anastomosis was performed. The postoperative course was uncomplicated until the eighth postoperative day when a minor anastomotic leak. The patient was discharged at 103 days of age.

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.4
• /
• pp.223-228
• /
• 2005

Tube hydroforming provides a number of advantages over conventional stamping process, including fewer secondary operation, weight reduction, assembly simplification, adaptability to forming of complex structural components and improved structural strength and stiffness. It can produce wide range of products such as subframe, engine cradle, and exhaust manifold. In this study, the effect of the heat treatment conditions such as post seam annealing (PSA) and bright annealing (BA) on the ovality and hydro-formability of steel tubes has been investigated. Hydroformabilities have been estimated by the bulging heights obtained at various processing parameters such as internal pressure, axial feeding and heat treatment conditions. The ovality and forming height are strongly influenced by material properties after heat treatments.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.194-197
• /
• 2004

In the tube hydroforming process, a tube is placed into the die cavity and the ends of the tube are sealed by fixing the axial cylinder piston into the ends. Then the tube is pressurized with a hydraulic fluid and simultaneously the axial cylinders move to feed the material into the expansion zone. Therefore, the quantitative relationship between process parameters such as internal pressure and feeding amount and hydroformabillity, is hard to establish because of their high complexity and many unknown factors. In this study, the empirical and the quantitative relationship between process parameters and hydroformabillity are analyzed by fuzzy rules. Fuzzy expert system is an advanced expert system which uses fuzzy rule and approximate reasoning. Many process parameters are converted to the quantitative relationship by use of approximate reasoning of fuzzy expert system. The comparison between experimentally measured hydroformabillity from hydroforming experiments and the predicted values by fuzzy expert system shows a good agreement.