• Journal of the Korean institute of surface engineering
• /
• v.54 no.5
• /
• pp.248-259
• /
• 2021

This study examined the influence of post weld heat treatment (PWHT) conditions on corrosion behaviors of laser-welded super duplex stainless steel tube. Due to the high cooling rate of laser welding, the phase fraction of ferrite and austenite in the weld metal became unbalanced significantly. In addition, the Cr₂N particles were precipitated adjacent to the fusion line, which can be susceptible to the localized corrosion. On the other hand, the phase fraction in the weld metal was restored at a ratio of 5:5 when exposed to temperatures above 1060 ℃ during the post weld heat treatment. Nevertheless, the high beltline speed during the PWHT, leading to the insufficient cooling rate, caused a precipitation of σ phase at the interface between ferrite/austenite in both weld metal and base metal. This resulted in the severe corrosion damages and significant decrease in critical pitting temperature (CPT), which was even lower than that measured in as-welded condition. Moreover, the fraction of σ phase in the center region of post weld heat treated steel tube was obtained to be higher than in the surface region. These results suggest that the PWHT conditions for the steel tube should be optimized to ensure the high corrosion resistance by excluding the precipitation of σ phase even in center region.

• Korea Science and Art Forum
• /
• v.37 no.3
• /
• pp.113-123
• /
• 2019

In line with policy support and demand, mobile videos about science and technology have growth potential. For activation of domestic mobile video contents about science and technology, this article aims to analysis current global leading contents and draw implications for benchmarking. Therefore, this paper attempted to analyzed types and storytelling strategy of Science and technology channels on YouTube, which has the most influence among the mobile video media. The results are as follows. Fist, the YouTube contents about science technology are categorized into three types, activity-, explain-, review-centered type. Second, activity type channels are classified into 4 sub-types. Third, The core storytelling strategy of activity type channels is a combination of familiarity and unfamiliarity to deal with everyday material through specialized scientific and technological methods. Based on the results of this research, we expect to plan and produce global killer contents.

• Imaging Science in Dentistry
• /
• v.49 no.2
• /
• pp.139-151
• /
• 2019

Purpose: This study was performed to investigate the effect of exposure parameters on image quality obtained using a cone-beam computed tomography (CBCT) scanner and the relationship between physical factors and clinical image quality depending on the diagnostic task. Materials and Methods: CBCT images of a SedentexCT IQ phantom and a real skull phantom were obtained under different combinations of tube voltage and tube current (Alphard 3030 CBCT scanner, 78-90 kVp and 2-8 mA). The images obtained using a SedentexCT IQ phantom were analyzed technically, and the physical factors of image noise, contrast resolution, spatial resolution, and metal artifacts were measured. The images obtained using a real skull phantom were evaluated for each diagnostic task by 6 oral and maxillofacial radiologists, and each setting was classified as acceptable or unacceptable based on those evaluations. A statistical analysis of the relationships of exposure parameters and physical factors with observer scores was conducted. Results: For periapical diagnosis and implant planning, the tube current of the acceptable images was significantly higher than that of the unacceptable images. Image noise, the contrast-to-noise ratio (CNR), the line pair chart on the Z axis, and modulation transfer function (MTF) values showed statistically significant differences between the acceptable and unacceptable image groups. The cut-off values obtained using receiver operating characteristic curves for CNR and MTF 10 were useful for determining acceptability. Conclusion: Tube current had a major influence on clinical image quality. CNR and MTF 10 were useful physical factors that showed significantly associations with clinical image quality.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.2
• /
• pp.118-124
• /
• 2010

In this paper, design parameters of dynamic vibration absorber, which is used to reduce bending vibrations of a vehicle drive line, is optimized. For obtaining the correct dynamic response characteristics, a flexible-body drive line is made by applying the flexibility data extracted from vibration analysis of propeller shafts to the drive line dynamic model. Inner tube mass, rubber stiffness and rubber damping coefficient of the dynamic vibration absorber are taken as design parameters for optimization. To minimize the vertical acceleration of the drive line, a second-order regression equation of the objective function is generated by performing the central composite experimental design with 3 factors, 2 levels and 15 test runs. And the design parameters of the dynamic vibration absorber are determined by using optimization program. The vehicle model with optimized dynamic vibration absorber reduces the vertical acceleration peak of the drive line by 17.1 % in compared with the initial model.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.9 no.4
• /
• pp.1-6
• /
• 1972

A super widely amplitude modulating AM modulator system, utilizing the impedance trasformation characteristics of transmission line is presented. The analyses and oscillograms obtained from the AM modulator systems using VHF tube, FET or VVC diode as an active element are added to verify the principle of the system.

• Journal of Korean Society for Quality Management
• /
• v.29 no.3
• /
• pp.124-137
• /
• 2001

In general, it is very efficient and effective to use screening variables that are correlated with the performance variable in case that measuring the performance variable is impossible (destructive) or expensive. The general methodology for searching surrogate variables is regression analysis. This paper considers the inspection problem in CRT (Cathode Ray Tube) production line, in which the performance variable (dependent variable) is binary type and screening variables are continuous. The general regression with dummy variable, discriminant analysis and binary logistic regression are considered. The cost model is also formulated to determine economically inspection procedure with screening variables.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.10a
• /
• pp.102-109
• /
• 1997

The surface deformation of shadow mask was studied by the experiments and numerical analysis for process improvement and delet of the stabilizing process in the shadow mask manufaturing line. To inverigate the thermal deformation of shadow mask with and without stabilizing process mask, data of spring strength, frame flatness, frame magnetic force and a mask surface curvature were measured. The tube characteristics of two kind of shadow masks were also investigated.

• Korean Journal of Plant Resources
• /
• v.3 no.1
• /
• pp.1-30
• /
• 1990

The traditional plant imprownent methods consisted of pure line selection, cross breeding, heterosis breeding, polyploid breeding, mutati-onbreeding, ect.Biotechmoiogy is divided into gene spliclng , monocle-nal antibodies , protein engineering , agricultural research, and microbiological engineering. Of these , high plants deal with agricultural research, and the importent part of which is tissue culture and celLculture , Tissue .culture and cell culture are again divided into embryoculture, test tube fertilization, anther and pollen culture, somatichybridization , transformation, recombination, recombinant DNA moleculehybrid plasmid, ect For these haploid production, protoplast culture,protoplast fusion, selection and propagation, ect. , the technical sett-lement is needed.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.1
• /
• pp.45-49
• /
• 2015

Process gases with vapor or liquid phase as well as gas phase may experience alteration in itself or be contaminated in the fluid pipe to the process chamber. And thus it result in as particles or defects on the substrates in semiconductor, LCD, LED manufacturing. Purifiers and filters are used for control of contamination. However, none of detection device is available in the delivery line. In this paper, we propose simple device with lighting and sensing in order to predict contamination of the fluid or the tube wall. For some general purpose gases, it showed constant voltage output regardless of the flow rates. But, the smoke and the moisture in the air lowered the figure due to its concentration. Numerical values for several solid and liquid media were obtained. And, the operating temperature tendency was investigated.

• Journal of Welding and Joining
• /
• v.11 no.1
• /
• pp.21-32
• /
• 1993

A cracking failure of a austenitic stainless steel elbow in a naphtha cracking line in a petrochenmical plant occurred, resulting in leakage of organic compound flowing inside the elbow. Due to the failure, emergency shutdown of the plant was enforced to repair the troubled part of the line. The repair cost as well as production loss during the unscheduled plant shutdown has cost the company a great amount of financial loss. In this studies, a failure analysis of the cracked elbow was performed using NDT, chemical analysis, microstructural analysis including optical microscopy as well as scanning electron microscopy with EPMA, mechanical testings such as tensile testing, hardness testing and Charphy impact test fractography. The results indicated that several problems such as a welding defect and presence of a detrimental phase which was found to be relate to improper postforming heat treatment process was identified and the failure was concluded to be due to a low temperature embrittlement of the defect-containing elbows.