• 조명전기설비학회논문지
• /
• 제27권6호
• /
• pp.95-99
• /
• 2013

Furnace is currently the most important doping process using POCl3 in solar cell. However furnace need an expensive equipment cost and it has to purge a poisonous gas. Moreover, furnace typically difficult appling for selective emitters. In this study, we developed a new atmospheric pressure plasma source, in this procedure, we research the atmospheric pressure plasma doping that dopant is phosphoric acid($H_3PO_4$). Metal tube injected Ar gas was inputted 5 kV of a low frequency(scores of kHz) induced inverter, so plasma discharged at metal tube. We used the P type silicon wafer of solar cell. We regulated phosphoric acid($H_3PO_4$) concentration on 10% and plasma treatment time is 90 s, 150 s, we experiment that plasma current is 70 mA. We check the doping depth that 287 nm at 90 s and 621 nm at 150 s. We analysis and measurement the doping profile by using SIMS(Secondary Ion Mass Spectroscopy). We calculate and grasp the sheet resistance using conventional sheet resistance formula, so there are 240 Ohm/sq at 90 s and 212 Ohm/sq at 150 s. We analysis oxygen and nitrogen profile of concentration compared with furnace to check the doped defect of atmosphere.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.842-846
• /
• 2001

Our company produces boilers for industrial usages or power plants. The aim of this study is to investigate the flame structure, heat transfer to evaporator tube wall and NOx emission in the furnaces. Also we are to derive correct FEGT(Furnace Exit Gas Temperature) characteristic curve. When we design furnace and superheater, economizer etc. FEGT characteristic curve is very important factor for optimum design. We calculated turbulent reacting flow, heat transfer and NOx emission in furnace by using numerical modeling with the help of commercial code. Three dimensional steady state calculation is done. k-e turbulence model and equilibrium chemistry combustion model with $\beta-probability$ density function is used. To calculate radiation heat transfer discrete ordinates model is used. And we measured FEGT at several operating plants. Measurement is done by R-type thermocouple. Radiation shield is attached to the thermocouple to prevent radiation effect. Measured and calculated results show good agreement. And we could understand the flame structure and NOx formation positions in each furnaces.

• 비파괴검사학회지
• /
• 제9권1호
• /
• pp.98-105
• /
• 1989

Detection of creep damages in centrifugally cast HK-40 reformer furnace catalyst tube is a common problem for the safety and scheduled operation of chemical plants. This study was focused on the development of an automatic ultrasonic scanning device with which the creep damage of welded zone of HK-40 reformer tubes is detected and evaluated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.537-538
• /
• 2007

• 대한전기학회논문지
• /
• 제43권6호
• /
• pp.958-964
• /
• 1994

To study on the superconducting properties with cooling conditions, silver-sheathed Bi-Pb-Sr-Ca-Cu-O wires fabricated by the powder-in-tube method. The wires cooled down in the furnace, air and liquid NS12T after sintering at 840$^{\circ}C$ Critical current density of sample cooled in the furnace is 5.1${\times}$10S03TA/cmS02T and sample cooled in the air is 40A/cmS02T at 77K, zero magnetic field. The latter is very low critical current density of Bi system. 2223 high-Tc superconducting phase of sample cooled in the air was distroyed. Properties of sample cooled down in the liquid nitrogen is the same as cooled in the furnace.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.205-206
• /
• 2006

A ball-shape alumina arc-tube for low-wattage lamp was developed by the PIM process. An ultra high purity translucentgrade alumina powder was used. In injection molding process, a hot-runner type mold was developed. The translucent-grade alumina powder was extremely sensitive to contamination so that the injection molding condition and atmosphere control in the furnace should be taken care of with extreme caution. Contamination sources were pinpointed with EPMA. The arc-tube was molded in half and two halves were bonded in the middle by a new bonding technique at room temperature developed in this study.

• 한국대기환경학회:학술대회논문집
• /
• 한국대기환경학회 2006년도 춘계학술대회 논문집
• /
• pp.531-532
• /
• 2006

• 한국전산유체공학회지
• /
• 제18권4호
• /
• pp.69-73
• /
• 2013

Mass manufacturing of optical fiber includes the process of very thin glass fiber drawing by heating and softening the high purity silica preform and applying the draw tension on the softened tip of preform neck-down profile in a draw furnace. In this computational study, this process is numerically modeled with simplified geometry of the draw furnace which is comprised of essential parts such as concentric graphite heater, muffle tube, and insulation surrounding the heater. The iterative computational scheme is employed between one-dimensional model of neck-down profile prediction and two-dimensional axisymmetric thermo-fluid CFD computation of radiative heating and working gas convection. The computational results show the experimentally observed neck-down profile in heated section of preform, while yielding the reasonable values of draw tension and heater wattage. Also, this study analyzes and discusses the effects of heating conditions such as heater length and temperature on several important aspects of glass fiber drawing process.

• 한국화재소방학회논문지
• /
• 제28권1호
• /
• pp.44-51
• /
• 2014

화재현장에서 발생하는 연기는 일반적으로 연소가스와 더불어 여러 가지 성분의 유기증기 및 미연탄소로부터 생성된 미세입자로 되어 있다. 연기는 호흡기로 흡입되어 장단기 인체피해를 유발한다. 화재 시 발생하는 유독가스나 입자에 의한 피해를 예측하기 위해서는 연기입자의 호흡기관 내 이송과 침전, 그리고 입자를 매개로 한 유독가스의 흡수와 흡착등의 현상 파악이 필수적이며 이에 연기입자의 크기 및 형상은 이와 같은 현상의 변화에 중요한 변수로서 작용한다. 이 연구에서는 화재 시 발생하는 연기입자의 흡입에 의한 인체피해 특성을 예측하기 위하여 가연물 및 화재 조건에 따른 연기입자의 크기 및 형상에 대한 분석을 수행하였다. 국제표준에 따른 연소생성물 분석을 위하여 ISO/TS 19700 기준에 따라서 등속연소로를 제작하고 각 가연물에 대하여 연소로 온도 및 당량비 조건으로 정해지는 4가지 대표적인 화재조건, 즉, 저온불완전연소, 완전불꽃연소, 불완전불꽃연소, 고온불완전연소 조건에서 연기입자를 발생시켰다. 발생된 연기입자는 다단 충돌집진기를 이용하여 채집한 다음 투과전자현미경으로 크기 및 형상을 분석하였다.

• 한국안전학회지
• /
• 제30권1호
• /
• pp.8-13
• /
• 2015

The experimental design methodology was applied in the drop tube furnace (DTF) to predict the various combustion properties according to the operating conditions and to assess the coal plant safety. Response surface method (RSM) was introduced as a design of experiment, and the database for RSM was set with the numerical simulation of DTF. The dependent variables such as burnout ratios (BOR) of coal and $CO/CO_2$ ratios were mathematically described as a function of three independent variables (coal particle size, carrier gas flow rate, wall temperature) being modeled by the use of the central composite design (CCD), and evaluated using a second-order polynomial multiple regression model. The prediction of BOR showed a high coefficient of determination (R2) value, thus ensuring a satisfactory adjustment of the second-order polynomial multiple regression model with the simulation data. However, $CO/CO_2$ ratio had a big difference between calculated values and predicted values using conventional RSM, which might be mainly due to the dependent variable increses or decrease very steeply, and hence the second order polynomial cannot follow the rates. To relax the increasing rate of dependent variable, $CO/CO_2$ ratio was taken as common logarithms and worked again with RSM. The application of logarithms in the transformation of dependent variables showed that the accuracy was highly enhanced and predicted the simulation data well.