• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.144-147
• /
• 2002

In this study, springback analysis of side rear member is carried out. Side rear member is one of the parts which shows severe springback problems. Forming, trimming, flanging and springback stages can be analyzed successively. From forming analysis, we identified the possible spots in which tearing may occur and can prevent failure. In springback analysis we used the boundary conditions same as applied to the blank on the checker so that the computational result can be compared with experimental one. Form .the comparison, springback analysis can yield relatively good results in a qualitative sense. However, in order to get good deformation result quantitatively, there still remains unsettled tasks in the forming analysis with very small die radius. It is found that we have to develop the element with better bending characteristics and precise contact treatment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1440-1443
• /
• 2004

Shearing including punching, blanking, trimming, slitting, etc is one of the most frequently used processes in sheet metal manufacturing. It has been widely used for manufacturing autobody, electronic components, aircraftbody, etc. In this paper, it has been researched by the experiment to examine the effect of burr height corresponding to die clearance, cutting angle, tool sharpness, etc. This paper presents the experimental results with using Al alloy sheet.

• Transactions of Materials Processing
• /
• v.12 no.3
• /
• pp.236-243
• /
• 2003

Maintaining the required dimensional accuracy after springback becomes the main concern of sheet-forming die designers when formability is secured through beforehand tryouts. As a part to build guidelines for springback control in automobile frame forming, experiments are carried out to show the effects of process parameters, such as holding force, blank size, and lubrication, on corner angles of channels formed by U-bending or by square-cup drawing and trimming. The results predicted by a commercial FE package were compared with the experiment and the current limitations on springback evaluation were closely discussed.

• Transactions of Materials Processing
• /
• v.9 no.5
• /
• pp.526-532
• /
• 2000

Springback simulation is receiving increasing attention throughout the automotive industry and the academic world. The knowledge of the real springback of stamped parts can help the stamping technicians to modify the process parameters or die geometry in order to reduce the shape defect. This paper presents the results of springback simulation after aluminium square cup deep drawing and trimming simulation, and results of springback optimization using response surface method.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.90-93
• /
• 2002

Assuring required dimensional tolerance after spingback becomes the main concern of sheet-forming die designers when formability is secured through previous tryout. As a part to build a guideline to control springback in automobile frame forming, experiments are carried out to show the effects of process parameters, such as holding force, blank size, and lubrication, on corner angles of channels formed by U-bending or by square-cup drawing and trimming. The results are resented in the viewpoint of evaluating parameters.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.114-116
• /
• 2005

There are some problems when weld gray cast iron which is used well in automobile industry with auto MIG welding. the problems are followed like this 1) Occurrence of porosity and hardening organization. 2) Occurrence of crack due to lower elongation of gray cast iron when restraint stress works on. 3) Occurrence of porosity and unstable bead shape due to unstable arc under low current MIG welding.. especially there is a restraint on chemical composition of weld metal because the weldment demands more than 570Hv hardness. so it is hard to use Fe-Ni wire to prevent cracks occured on weldment and new welding method is needed to resolve that problems. This study shows how to prevent porosity and cracks occurring when weld gray cast iron trimming die and shows a new welding method for press die of gray cast iron

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.6
• /
• pp.88-96
• /
• 2006

The objective of this research works is to develop back panel dies of PDP TV with a large size. In order to design the geometry of the dies and an initial size of blank optimally, the finite element analysis has been carried out using AUTOFORM V4.2. The conner radius of the upper trimming area and the distance from the outer line of the blank holder to the outer line of the blank have been selected as design parameters to remove the wrinkling of the trimming area. The results of the analyses have been shown that a feasible product without wrinkles and skid lines can be obtained when the conner radius ranges from 6mm to 8mm and the distance lines in the range of 40-60mm. From the proposed design of the dies and an initial blank size, the final die set of the back panel has been successfully manufactured.

• Transactions of Materials Processing
• /
• v.20 no.4
• /
• pp.273-278
• /
• 2011

Employing the TRIZ problem solving technique, a hybrid-type center plate for the molten carbonate fuel cell(MCFC) was developed for the purpose of improving gas sealing and maintenance. The manufacturing method of the hybrid-type center plate was divided into a trimming operation and a two-step bending process. In the latter, a modified punch shape was used to reduce springback. Using finite element(FE) simulations, bending stresses in the thickness and the in-plane directions were computed and the bending conditions were optimized. The optimized results of the two-step bending process were used as a basis for the design of the trimming process of the hybrid-type center plate. Finally, the external manifold-type center plate and the hybrid-type center plate were fabricated using a die set that accounts for the optimized conditions. It was found that the numerical simulation results were in good agreement with the experiments.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.320-324
• /
• 2016

A new eccentric forging process for camber bolts has been suggested in this study. The camber bolt is manufactured by a two-step process: the typical forging process for normal bolts and the trimming process for the eccentric flange. The processes are performed under high forging load and generate a large amount of chip during trimming. A new forging process has been required in order to overcome these problems. The eccentric forging is the new process in which the load axis is offset from the central axis, as against central load applied in a typical forging process. The eccentric forging process could reduce forging load and save the amount of chip. In order to manufacture camber bolts by an optimum process, it is required to adjust the geometry of eccentric die and the offset from the central axis.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.2
• /
• pp.17-21
• /
• 2007

Shearing including punching, blanking, trimming, slitting, etc is one of the most frequently used processes in sheet metal manufacturing. It has been widely used for manufacturing autobody, electronic components, aircraftbody, etc. In this paper, it has been researched by the experiment to examine the effect of burr height corresponding to die clearance, cutting angle, tool sharpness, etc. This paper presents the experimental results with using Al alloy sheet.