• The Korean Journal of Ceramics
• /
• 제2권4호
• /
• pp.226-230
• /
• 1996

A small amount of fine particle graphite was added to $\alpha$-SiC and $\beta$-SiC having certain particle distributions, and they were mixed clay and frit. After forming, they were sintered at 140$0^{\circ}C$ for 3 hours. Tribological properties of sintered $\alpha$-SiC-$\beta$-SiC-graphite-clay (frit) system showed that kinetic friction coefficient was 0.108, specific wear rate was 1.3${\times}10^-8\;mm^2$.$kgf^1$, and torque was 0.01kgf.cm at the wrench torque of 100 kgf.cm.

• Tribology and Lubricants
• /
• 제11권3호
• /
• pp.40-47
• /
• 1995

The engine oil life was examined experimentally for small size single cylinder engines. This study was conducted in the laboratory. An Eddy Current type engine dynamometer was used with a motorcycle and a cultivator engine. Physical and chemical properties of used oil was analyzed to examine the oil life. Flushed oil was used for the reference instead of the new oil. It were found that deterioration of dynamic viscosity and anti-wear property of engine oil was due to dilution by fuel not depletion of ZDTP.

• Tribology and Lubricants
• /
• 제15권1호
• /
• pp.108-115
• /
• 1999

The electrical and frictional properties of oil-impregnated sintered-metal bearing (OSB) and herringbone-grooved fluid bearing (HFB) with varying loads and speeds were measured. OSB shows very good performance up to 20,000 rpm and 0.05 N, and HFB successfully works up to 35,000 rpm and 0.05 N. From the endurance tests on start-stop and continuous operation, it was confirmed that those bearings could be mass-produced fur use on scanner motor in a laser scanner unit.

• Tribology and Lubricants
• /
• 제17권2호
• /
• pp.124-129
• /
• 2001

The electrical and rheological behaviors of the cellulose phosphate ester suspension in the silicone oil were investigated. Cellulose phosphate ester suspension showed a typical ER response (Bingham flow behavior) upon application of an electric field. The shear stress for the cellulose phosphate ester suspension exhibited a linear dependence on the volume fraction of particles and a square power of the electric field. On the basis of the experimental results, cellulose phosphate ester suspension correlated with the conduction model of Tang et al, and found to be an ER fluid.

• Tribology and Lubricants
• /
• 제13권3호
• /
• pp.108-114
• /
• 1997

The electrical and frictional properties of new sintered-metal bearing (S-bearing) with varying loads and speeds were measured. Also those were compared with the same products(J-bearing) made in Japan and the conventionally used ball bearing. The test results show that the frictional values of S-bearing are less than those of J-bearing, and that S-bearing operates in full-hydrodynamic lubrication regime. The values of rating current, starting time and jitter reveal that S-bearing is superior to J-bearing as well as ball bearing.

• Tribology and Lubricants
• /
• 제32권2호
• /
• pp.39-43
• /
• 2016

Magnetorheological elastomers (MREs) are a type of “smart” material, and their properties can be controlled rapidly and reversibly under the influence of an external stimulus. The application of an external magnetic field can change the shear modulus, hardness, and friction coefficient of MREs. The friction can cause vibration; moreover, the vibration can affect friction. The change of friction depends on the relative motion, normal force, roughness of the rubbing surfaces, material type, temperature, lubrication, relative humidity, and vibration condition. As MREs are a type of “smart material,” their friction coefficient can be reduced by applying an external magnetic field—the applications of this feature in engineering have been widely studied. However, the friction properties of MREs under vibration have not been tested to date. In this study, MRE samples and a reciprocating friction tester were fabricated. The friction coefficient was measured to evaluate the friction properties under various vibration conditions; subsequently, the wear depth and wear surface profile of the MRE were observed in order to evaluate the wear properties. The results show that the friction coefficient of the MREs decreased when a magnetic field was applied. Moreover, the friction coefficient decreased when the vibrational amplitudes increased. The wear depth of the MRE also decreased as the vibrational amplitudes increased.

• Tribology and Lubricants
• /
• 제30권5호
• /
• pp.247-255
• /
• 2014

Charged polymer chains, i.e., polyelectrolytes, are known to show superior aqueous lubricating properties compared to those of neutral polymer chains, especially in brush conformation. This is primarily because of the incorporation of a large amount of counterions within the polymer layers and the consequently increased osmotic pressure. However, this effect is active only when the polymer chains remain immobilized even under tribostress, which is not realistic for high-contact pressure tribological applications, especially when they are irreversibly immobilized on tribopair surfaces. In contrast, with free polymers, which can be included as surface-active additives in the base lubricant (water), long-term lubricating performance based on "self-healing" properties is readily expected. In order to assess whether the superior aqueous lubricating properties of polyelectrolyte chains are valid for free polymers too, this study reviews recent studies on the tribological properties of many charged biopolymer and synthetic copolymers at a nonpolar, hydrophobic interface. In contrast to the irreversibly immobilized polyelectrolyte chains, free polyelectrolyte chains show inferior aqueous lubricating properties compared to their neutral counterparts owing to charge accumulation and the consequently impeded surface adsorption on the nonpolar surface. Nevertheless, bovine submaxillary mucin (BSM), a representative biopolymer, shows a sufficiently effective surface adsorption and aqueous lubricating capabilities even at neutral pH without losing the polyanionic characteristics.

• Tribology and Lubricants
• /
• 제37권6호
• /
• pp.203-207
• /
• 2021

This study presents the development of dielectric constant sensors to measure lubricant properties. The lubricant oil sensor is used to measure oil properties and machine conditions. Various condition monitoring methods are applied to diagnose machine conditions. Machine condition monitoring using oil sensors has advantage over other machine condition monitoring methods. The fault conditions can be noticed at the early stages by the detection of wear particles using oil sensors. Therefore, it provides an early warning in the failure procedure. A variety of oil sensors are applied to check the machine condition. Among all oil sensors, only one sensor can measure the tendency of several properties such as acidity and water content. A dielectric constant sensor is also used to measure various oil properties; therefore, it is very useful. The dielectric constant is the ratio of the capacitance of a capacitor using that material as a dielectric to that of a similar capacitor using vacuum as its dielectric. The dielectric constant has an effect on water content, contaminants, base oil, additive, and so forth. In this study, the dielectric constant sensor is fabricated using MEMS process. In the fabrication process, the shape, gap of the electrode array, and thickness of the insulation material are considered to improve the sensitivity of the sensor.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.43-44
• /
• 2002

Langmuir-Blodgett mono- and multilayer films from 2,4-heneicosanedione have been examined as lubrication coatings In the process of wear. Tribological properties of the films have been studied by atomic force microscopy and microtribometer. It has been observed that the wear resistance of silicon surface coated with OTS/LB multilayer system increased by several orders of magnitude compared to uncoated surfaces at low normal load. The results obtained suggest that the system constructed on silicon surface reduces surface energy, friction coefficient and increases life of substrate due to a possibility of LB film self-repairing during frictional contact.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.323-329
• /
• 2004

The electrical and rheological properties pertaining to the electrorheological (ER) behavior of chitosan derivatives, chitosan, chitosan ammonium salt and chitosan phosphate suspensions in silicone oil were investigated. Chitosan derivative suspensions showed a typical ER response (Bingham flow behavior) upon application of an electric field. However, chitosan phosphate suspension exhibited an excellent shear yield stress compared with chitosan and chitosan ammonium salt suspensions. The difference in behavior results from the difference in the conductivity of the disperse phases due to the difference of their polarizability. The shear stress for the chitosan, chitosan ammonium salt and chitosan phosphate suspensions exhibited a linear dependence on the volume fraction of particles and 1.18 ,1.41 and 1.67 powers of the electric field. On the basis of the experimental results, the newly synthesized chitosan derivative suspensions found to be an ER fluid.