• 열처리공학회지
• /
• 제35권6호
• /
• pp.314-318
• /
• 2022

Transparent conducting ZnO/Ti/ZnO tri-layer films deposited on glass substrate with DC and RF magnetron sputtering were rapid thermal annealed at 150, 300 and 450℃ for 5 minutes and then effect of annealing temperature on the structural and optoelectronics properties of the films were investigated. The structural properties are strongly related to annealing temperature and the largest grain size is observed in the films annealed at 450℃. The electrical resistivity also decreases as low as 7.7 × 10^-4 Ωcm. The visible transmittance also depends on the annealing temperature. The films annealed at 450℃ show a higher transmittance of 80.6% in this study.

• Asian-Australasian Journal of Animal Sciences
• /
• 제29권6호
• /
• pp.865-871
• /
• 2016

The objective of this study was to investigate the effects of canola and flaxseed oils on the physicochemical properties and sensory quality of emulsion-type sausage made from spent layer meat. Three types of sausage were manufactured with different fat sources: 20% pork back fat (CON), 20% canola oil (CA) and 20% flaxseed oil (FL). The pH value of the CA was significantly higher than the others (p<0.05). The highest water holding capacity was also presented for CA; in other words, CA demonstrated a significantly lower water loss value among the treatments (p<0.05). CA had the highest lightness value (p<0.05). However, FL showed the highest yellowness value (p<0.05) because of its own high-density yellow color. The texture profile of the treatments manufactured with vegetable oils showed higher values than for the CON (p<0.05); furthermore, CA had the highest texture profile values (p<0.05) among the treatments. The replacement of pork back fat with canola and flaxseed oils in sausages significantly increased the omega-3 fatty acid content (p<0.05) over 15 to 86 times, respectively. All emulsion sausages containing vegetable oil exhibited significantly lower values for saturated fatty acid content and the omega-6 to omega-3 ratios compared to CON (p<0.05). The results show that using canola or flaxseed oils as a pork fat replacer has a high potential to produce healthier products, and notably, the use of canola oil produced characteristics of great emulsion stability and sensory quality.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.275-276
• /
• 2009

We have studied physical properties of organic light-emitting diodes (OLEDs) in a device with 7,7,8,8-tetracyanoquinodimethane (TCNQ). Since the TCNQ has a high electron affinity, it is widely used for a charge-transport and injection layer. And the TCNQ-derivatives have also been used to control the conductivity of the materials. It is known that a charge injection and transport in OLEDs with a TCNQ-derivative enhances a performance of the devices such as operating voltage and efficiency. To see how the TCNQ affects on the device performance, we have made a reference device in a structure of ITO(170nm)/TPD(40nm)/$Alq_3$(60nm)/LiF(0.5nm)/Al(100nm). And several type of devices were manufactured by doping TCNQ either in TPD or $Alq_3$ layer. The TCNQ layer was also formed in between the organic layers. N,N'-diphenyl-N,N'-di(m-tolyl)-benzidine (TPD), tri(8-hydroxy quinoline) aluminium ($Alq_3$), and TCNQ layers were formed by thermal evaporation at a pressure of $10^{-6}$ torr. The deposition rate was $1.0{\sim}1.5\;{\AA}/s$ for TPD, and $1.0{\sim}1.5\;{\AA}$ for $Alq_3$. The LiF was thermally evaporated at a deposition rate of $0.2\;{\AA}/s$ successively. The device with TCNQ-derivative improved the turn-on voltage compared to the one without TCNQ-derivative.

• Current Photovoltaic Research
• /
• 제2권4호
• /
• pp.147-151
• /
• 2014

A boron doping process using a boron tri-bromide ($BBr_3$) as a boron source was applied to form a $p^+$ emitter layer on an n-type mono-crystalline CZ substrate. Nitrogen ($N_2$) gas as an additive of the diffusion process was varied in order to study the variations in sheet resistance and the uniformity of doped layer. The flow rate of $N_2$ gas flow was changed in the range 3 slm~10 slm. The sheet resistance uniformity however was found to be variable with the variation of the $N_2$ flow rate. The optimal flow rate for $N_2$ gas was found to be 4 slm, resulting in a sheet resistance value of $50{\Omega}/sq$ and having a uniformity of less than 10%. The process temperature was also varied in order to study its influence on the sheet resistance and minority carrier lifetimes. A higher lifetime value of $1727.72{\mu}s$ was achieved for the emitter having $51.74{\Omega}/sq$ sheet resistances. The thickness of the boron rich layer (BRL) was found to increase with the increase in the process temperature and a decrease in the sheet resistance was observed with the increase in the process temperature. Furthermore, a passivated emitter solar cell (PESC) type solar cell structure comprised of a boron doped emitter and phosphorus doped back surface field (BSF) having Ni/Cu contacts yielding 15.32% efficiency is fabricated.

• Restorative Dentistry and Endodontics
• /
• 제47권1호
• /
• pp.4.1-4.13
• /
• 2022

Objectives: This study evaluated the effects of different smear layer preparations on the dentin permeability and microtensile bond strength (µTBS) of 2 self-etching adhesives (Clearfil SE Bond [CSE] and Clearfil Tri-S Bond Universal [CTS]) under dynamic pulpal pressure. Materials and Methods: Human third molars were cut into crown segments. The dentin surfaces were prepared using 4 armamentaria: 600-grit SiC paper, coarse diamond burs, superfine diamond burs, and carbide burs. The pulp chamber of each crown segment was connected to a dynamic intra-pulpal pressure simulation apparatus, and the permeability test was done under a pressure of 15 cmH₂O. The relative permeability (%P) was evaluated on the smear layer-covered and bonded dentin surfaces. The teeth were bonded to either of the adhesives under pulpal pressure simulation, and cut into sticks after 24 hours water storage for the µTBS test. The resin-dentin interface and nanoleakage observations were performed using a scanning electron microscope. Statistical comparisons were done using analysis of variance and post hoc tests. Results: Only the method of surface preparation had a significant effect on permeability (p < 0.05). The smear layers created by the carbide and superfine diamond burs yielded the lowest permeability. CSE demonstrated a higher µTBS, with these values in the superfine diamond and carbide bur groups being the highest. Microscopic evaluation of the resin-dentin interface revealed nanoleakage in the coarse diamond bur and SiC paper groups for both adhesives. Conclusions: Superfine diamond and carbide burs can be recommended for dentin preparation with the use of 2-step CSE.

• 한국전자파학회논문지
• /
• 제22권12호
• /
• pp.1069-1077
• /
• 2011

본 논문에서는 선택적 산화 알루미늄(SAAO: Selectively Anodized Aluminum Oxide) 기판을 이용하여 2.5 GHz 8 W급 소형 GaN HEMT 전력 증폭기 모듈을 설계, 제작하였다. SAAO 기판 공정은 최근 Wavenics사에서 제안한 특허 기술로서, 알루미늄을 웨이퍼로 이용한다. 본 연구에 사용된 능동 소자는 최근 발표된 TriQuint사의 칩 형태 의 GaN HEMT이다. 최적의 임피던스는 수동 조정 소자가 내장된 지그를 사용하여 실험적으로 결정하였다. 결정된 임피던스를 이용하여, 입 출력 임피던스 정합 회로를 EM co-시뮬레이션을 이용하여 F급으로 설계를 수행하였으며, SAAO 기판에 구현하였다. 이때, 소형의 패키지(모듈)에 집적하기 위하여 인덕터와 커패시터는 각각 spiral inductor, single layer capacitor를 사용하였다. 소형으로($4.4{\times}4.4\;mm^2$) 패키지된 전력 증폭기 모듈의 경우, 출력은 8 W, 효율은 40 % 그리고 2차 및 3차 고조파에 대한 고조파 억제는 30 dBc 이상의 특성을 보였다.

• 한국자원식물학회지
• /
• 제16권1호
• /
• pp.89-98
• /
• 2003

본 연구에서는 Atractylodes속과 혼용되는 Atractylis속 6분류군의 화분을 광학현미경과 주사전자현미경으로 관찰하였다 본 속의 화분은 단립(monad)으로, 극축의 길이는 46.5-66.7$\mu\textrm{m}$, 적도면의 나비는 43.6-60.47$\mu\textrm{m}$이 었다. 발아구는 3공구형 (tri-colporate)으로서 , 구구(colpus)의 길이는 19.6-29.1 $\mu\textrm{m}$, 나비는 7.3-11.0$\mu\textrm{m}$이 었고, 공구의 직경 은 6.4-10.6$\mu\textrm{m}$ 이었다. 화분벽은 외표벽 (ektexine)은 기저층(foot layer)과 원주층(columellae), 피복층(tectum)으로 구성되고, 두에는 5.2-8.3$\mu\textrm{m}$이었다. 화분의 표면 돌기는 자상(echinate)으로서 길이가 1.4-5.8$\mu\textrm{m}$이었으며, 단위면적당(No./20$\mu\textrm{m}$$^2$) 분포는 6-33개 이었다 본 연구에서 취급된 분류군들의 화분, 특히 Atractylis arabica, A. aristata, A. carduus, A. microcephala의 화분형 태는 Atractylodes속의 화분과 매우 유사하였으며, 따라서 화분에 관련된 형질은 두 속을 구분하는 식별형질로 적용할 수 없었다. 그러나 화분에 관련된 형질이 Atractylodes속에서는 화분의 크기만이 속내 분류군간의 식별형질로서 기여도가 적은 반면, Atractylis속에서는 화분의 크기뿐만 아니라 형태 및 표면무늬와 자상돌기의 크기 등에 있어서 분류군간 의 식별형질로서 적용되어 분류학적 기여도가 다소 큰 것으로 판단된다. 또한 본 연구에서 취급된 분류군 중 A. cancellata와 A. prolifera는 나머지 분류군들과 달리 자상돌기가 작고 적도면상이 긴 특징은 본속의 화분의 진화경 향성을 파악하는데 매우 유용하였다.

• 한국가금학회지
• /
• 제44권1호
• /
• pp.41-49
• /
• 2017

본 연구는 6주령 브로일러(Arbor Acre)와 함께 70, 95주령 산란 성계(Hy-line)의 가슴육과 다리육을 이용해 주령에 따른 산란 성계육의 육질특성 및 가공적성을 브로일러와 비교 평가하여 원료육으로서의 가치를 구명하고자 실시하였다. 브로일러는 생육과 유화물에서 우수한 보수력 및 유화안정성을 보였으며, 관능평가에 있어서 높은 점수를 받았다. 성계육 내에서 연령이 증가할수록 조직감이 질긴 특성을 보였으나, PUFA/SFA 및 n-6/n-3 지방산 조성이 유사하고, 가열육에 대한 관능검사 결과, 연령에 따른 차이를 나타내지 않았으며, 생육과 유화물에서의 가열감량과 수분손실이 유사하여 가공육의 원료로서 95주령 성계육이 70주령의 성계육과 동등한 수준의 이용성을 지닌 것으로 판단할 수 있었다.

• 전자공학회논문지
• /
• 제53권4호
• /
• pp.79-86
• /
• 2016

물리계층보안은 신호의 물리적 특성을 이용하여 정보를 보호하는 보안 기법이다. 현재 이에 대한 연구가 활발히 진행 중이지만 해결해야할 다음과 같은 문제점들이 존재한다. 도청자는 자신의 존재를 숨기기 위해서 자신의 채널상태정보를 다른 합법적인 노드와 공유하지는 않는다. 그리고 노드가 신호를 전송할 때 하드웨어 왜곡이 발생하지만 많은 연구들은 노드 모델들이 이상적인 것으로 가정을 하고, 하드웨어 왜곡문제를 고려하지 않고 있다. 이와 같은 문제점들을 해결하기 위한 본 논문의 주요한 특징 및 기여도는 다음과 같다. 첫째, 도청자의 채널상태정보를 얻기 위해서 조력자노드를 합법적인 노드주변에 설치하고, 조력자노드의 채널상태정보를 이용하여 노드모델에서 하드웨어 왜곡을 고려한다. 둘째, 제안된 시스템 모델의 인터셉트 확률에 대한 Closed-Form Expression을 제시한다. 제안된 시스템의 성능평가를 위해서 다양한 시뮬레이션를 통하여 제안된 시스템 모델의 물리계층보안에 미치는 영향을 알아본 결과, 불완전한 채널상태정보는 인터셉트 확률에는 영향을 미치지 못한 반면에, 불완전한 노드모델의 경우, 인터셉트 확률, 에르고딕 시크리스 용량과 보안채널용량에 영향을 준다는 것을 보여준다.

• 한국세라믹학회지
• /
• 제51권5호
• /
• pp.418-423
• /
• 2014

Fully ceramic micro encapsulated (FCM) nuclear fuel is a concept recently proposed for enhancing the stability of nuclear fuel. FCM nuclear fuel consists of tristructural-isotropic (TRISO) fuel particles within a SiC matrix. Each TRISO fuel particle is composed of a $UO_2$ kernel and a PyC/SiC/PyC tri-layer which protects the kernel. The SiC ceramic matrix is created by sintering. In this FCM fuel concept, fission products are protected twice, by the TRISO coating layer and by the SiC ceramic. The SiC ceramic has proven attractive for fuel applications owing to its low neutron-absorption cross-section, excellent irradiation resistivity, and high thermal conductivity. In this study, a SiC-matrix composite containing TRISO particles was sintered by hot pressing with $Al_2O_3-Y_2O_3$ additive system. Various sintering conditions were investigated to obtain a relative density greater than 95%. The internal distribution of TRISO particles within the SiC-matrix composite was observed using an x-ray radiograph. The fracture of the TRISO particles was investigated by means of analysis of the cross-section of the SiC-matrix composite.