• Fibers and Polymers
• /
• v.5 no.1
• /
• pp.25-30
• /
• 2004

The present paper reports the impact of thermal treatment on the characteristics of core-sheath type hybrid technical yarns. The core-sheath type hybrid yams are prepared using DREF-III technology. Polyester and glass multifilaments are used as core components whereas the cotton and polyester staple fibers are the sheath components wrapped around the core filament with different proportions to form a hybrid structure. The thermal treatment is carried out both in dry and in wet state under relaxed condition and the thermal shrinkage, sheath-slipping resistance and tensile and bending properties of hybrid yarns have been studied. Thermal treatment markedly increases the thermal shrinkage and sheath-slipping resistance of hybrid yarns with polyester multifilament in core, but insignificant effect for yarns with glass multifilament in core. Breaking elongation of hybrid yams with polyester multifilament in core increases with treatment temperature. The hybrid yarns with glass multifilament in core are least affected by thermal treatment.

• Journal of the Korean institute of surface engineering
• /
• v.16 no.3
• /
• pp.98-107
• /
• 1983

A study on the improvement of wear resistance of brasses by electroplating and diffusion treatment of tin was carried out. The optimum condition of the treatment obtained was as follows. Plating thickness of tin : 5 - 9 $\mu\textrm{m}$ Condition of diffusion treatment : atmosphere ; fused nitrate bath (KNO3 + NaNO3) temperature and time ; 1st step 320$^{\circ}C$, 60min. and 450$^{\circ}C$, 30min. During the diffusion treatment, internetallic compounds of Cu-Sn were formed and these compounds were identified as η, $\varepsilon$ and $\delta$ phase from the outer tin layer. It was considered that the improvement of wear resistance of brasses by the treatment is because of the formation of intemetallic compounds particalarly $\varepsilon$phase which is very hard, between soft tin layer brass.

• 연구논문집
• /
• s.26
• /
• pp.121-132
• /
• 1996

The carburising surface modification treatment of the die steel has been used for improving wear resistance and heat cycle strength of the die and preventing a pitting on the surface because the carbides are forming in the matrix during carburising. Generally, the hot forging die was used after quenching-tempering treatment or nitriding after quenching-tempering treatment. The nitriding after carburising on the surface of a hot die steel and a wear resistance die steels was suggested by SOUCHARD, JACQUOT. and BUVRON. This surface modification treatment improved the adhesive and abrasive wear resistance and friction coefficient. The process was introduced to the forging die of stainless steel, titanium alloy steel, alloy and medium carbon steel and the physical properties of the die after the treatment were improved. The surface hardening treatment of the nitriding, the carburising, the boriding, and TD process were used to improved the life time of the forging die. Also, the coating process of PVD, CVD and PCVD were used and the hard chromium plating was occasionally used. Therefore, this study analyzed the effects of the carburising time and the conditions of nitriding on STD61 steel. The case depth, the surface hardness, the forming carbide size and shape during overcarburising process on the die steel were also examined.

• Corrosion Science and Technology
• /
• v.13 no.1
• /
• pp.28-35
• /
• 2014

Recently, the fuel oil of diesel engines of marine ships has been increasingly changed to heavy oil of low quality as the oil price is getting higher and higher. Therefore, the spiral gear attached at the motor of the oil purifier which plays an important role to purify the heavy oil is also easy to expose at severe environmental condition due to the purification of the heavy oil in higher temperature. Thus, the material of the spiral gear requires a better mechanical strength, wear and corrosion resistance. In this study, the heat treatment(tempering) with various holding time at temperature of $500^{\circ}C$ was carried out to the alloy of Cu-7Al-2.5Si as centrifugal casting, and the properties of both hardness and corrosion resistance with and without heat treatment were investigated with observation of the microstructure and with electrochemical methods, such as measurement of corrosion potential, cathodic and anodic polarization curves, cyclic voltammogram, and a.c. impedance. in natural seawater solution. The ${\alpha}$, ${\beta}^{\prime}$ and ${\gamma}_2$ phases were observed in the material in spite of no heat treatment due to quenching effect of a spin mold. However, their phases, that is, ${\beta}^{\prime}$ and ${\gamma}_2$ phases decreased gradually with increasing the holding time at a constant temperature of $500^{\circ}C$. The hardness more or less decreased with heat treatment, however its corrosion resistance was improved with the heat treatment. Furthermore, the longer holding time, the better corrosion resistance. In addition, when the holding time was 48hrs, its corrosion current density showed the lowest value. The pattern of corroded surface was nearly similar to that of the pitting corrosion, and this morphology was greatly observed in the case of no heat treatment. It is considered that ${\gamma}_2$ phase at the grain boundary was corroded preferentially as an anode. However, the pattern of general corrosion exhibited increasingly due to decreasing the ${\gamma}_2$ phase with heat treatment. Consequently, it is suggested that the corrosion resistance of Cu-7Al-2.5Si alloy can be improved with the heat treatment as a holding time for 48 hrs at $500^{\circ}C$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.4
• /
• pp.492-499
• /
• 2000

This study was investigated to compare the staining resistance of soft denture liners. Specimens were made of Coe-soft, Coe-comfort, Soft-liner, Visco-gel, and were stored in 1% methyleneblue solution for 24 hours. The amounts of color change before and after treatment with mono-poly and thermocycling were measured by colorimeter(TC-6FX, Tokyo Denshoku Co. Ltd, Japan) for evaluation of staining resistance. The following conclusions were drawn from this study. 1. The staining resistance of Visco-gel was increased, but there was no changes of staining resistance in Coe-soft, Coe-comfort, and Soft-liner after treatment with monopoly. 2. The staining resistance of the Coe-comfort was the least in all soft denture liners. 3. The staining resistance of Visco-gel and Soft-liner were decreased after thermocycling.

• Journal of the Korean Society for Heat Treatment
• /
• v.29 no.4
• /
• pp.168-175
• /
• 2016

Influence of trace amount of Ca addition on the corrosion resistance was comparatively investigated in solutionized Mg-4%Zn and Mg-4%Zn-0.1%Ca alloys. In as-cast state, the alloys were characterized by primary ${\alpha}-(Mg)$ dendrite with MgZn intermetallic compound particles. After solution-treatment, both alloys consisted of single ${\alpha}-(Mg)$ phase by dissolution of the compound particles into the matrix. It was found from the immersion and electrochemical corrosion tests that the Mg-4%Zn alloy had better corrosion resistance than the Mg-4%Zn-0.1%Ca alloy. Morphological and compositional analyses on the surface corrosion products indicate that the incorporation of Ca oxide with low PBR value into the surface corrosion products would be responsible for the decreased corrosion resistance of the Ca-containing alloy.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.6
• /
• pp.269-274
• /
• 2015

In this experiment, post-nitriding treatment was performed at $400^{\circ}C$ on AISI 316 stainless steel which was plasma carburized previously at $430^{\circ}C$ for 15 hours. Plasma nitriding was implemented on AISI 316 stainless steel at various gas compositions (25% $N_2$, 50% $N_2$ and 75% $N_2$) for 4 hours. Additionally, during post nitriding Ar gas was used with $H_2$ and $N_2$ to observe the improvement of surface properties. After treatment, the behavior of the hybrid layer was investigated by optical microscopy, X-ray diffraction, and micro-hardness testing. Potentiodynamic polarization test was also used to evaluate the corrosion resistance of the samples. Meanwhile, it was found that the surface hardness increased with increasing the nitrogen gas content. Also small percentage of Ar gas was introduced in the post nitriding process which improved the hardness of the hardened layer but reduced the corrosion resistance compared with the carburized sample. The experiment revealed that AISI 316L stainless steel showed better hardness and excellent corrosion resistance compared with the carburized sample, when 75% $N_2$ gas was used during the post nitriding treatment. Also addition of Ar gas during post nitriding treatment degraded the corrosion resistance of the sample compared with the carburized sample.

• Journal of Environmental Science International
• /
• v.11 no.4
• /
• pp.339-346
• /
• 2002

Physico-chemical properties of the activated sludges(Suyoung and Changlim treatment plant), such as SVI(sludge volume index), absorbance, specific surface area, and specific resistance using Buchener funnel test were investigated with changing anaerobic storage time. This experimental condition was found that it was possible to estimate a linear relationship between their parameters such as specific surface area specific resistance, and sludge volume index(SVI). The specific surface area and the specific resistance to filtration of the activated sludges of Suyoung and Changlim treatment plant were found as 123.6~136.6$m^2$/gDS and 41.5~44.9$m^2$/gDS(dry solid), and 1.09$\times$10$^{14}$ ~5.48$\times$10$_{14}$ m/kg and 1.05$\times$10$^{14}$ ~2.48$\times$10$^{14}$ m/kg, respectively. The results gave a good linear relationship between the specific surface area and the specific resistance, r=2.25$\times$10$^{12}$ s-8.10$\times$10$^{13}$ ($R^2$=0.8885) at Suyoung treatment plant and r=1.26$\times$10$^{13}$ s-4.75$\times$10$^{14}$ ($R^2$=0.8756) at Changlim treatment plant.

• Tuberculosis and Respiratory Diseases
• /
• v.64 no.2
• /
• pp.95-101
• /
• 2008

Background: Drug resistant tuberculosis (TB) in patients who have not received previous TB treatment (initial drug resistance) is a serious problem for the control of TB. However, prevalence of initial drug resistance among pulmonary TB patients has not been well characterized in Korea, especially in the private sector. We assessed the prevalence of initial drug resistance and evaluated the risk factors for drug resistance in pulmonary TB patients, at a regional tertiary hospital in Cheonan. Methods: We performed a drug susceptibility test for both first and second line anti-TB drugs in all culture-confirmed pulmonary TB patients who had not received a previous TB treatment at Dankook University Hospital from September 2005 to September 2007. In addition, we evaluated the initial drug resistance pattern and clinical characteristics of patients to evaluate the risk factors for initial drug resistance. We also assessed the influence of the drug susceptibility test results on the treatment regimen. Results: Of the total 156 cases where the drug susceptibility test was performed, resistance to at least one anti-TB drug was found in 21 cases (15.6%) and multidrug resistance, where TB was resistant to at least isoniazid and rifampin, was found in one case (0.6%). Multivariate logistic regression showed no clinical characteristics were independently associated with initial drug resistance. Of the total 156 patients who underwent the drug susceptibility test, the treatment regimen was changed for 15 patients (9.6%) according to the results of the drug susceptibility test. Conclusion: Initial drug resistance is common and the drug susceptibility test is informative for pulmonary TB patients who have not received previous TB treatment.

• Korean Journal of Environmental Agriculture
• /
• v.19 no.2
• /
• pp.160-165
• /
• 2000

This study was carried to select the tolerance in rice varieites for ozone treatment through comparing SOD, POD and stomata resistance. In SOD Acivity, Sangnambatbyeo showed the highest activity on 1 hr after ozone treatment and after 24 hr, SOD activity was decreased. SOD activity of Hangangchalbyeo was not different in observed all times after ozone treatment. In POD activity, Hangangchalbyeo, Sangnambatbyeo and Ilpumbyeo were similar to POD activity but Baeknabyeo was the lowest activity on 1 hr after ozone treatment. Also, all varieties represnted the highest activity (above 90 %) an 24 hr after ozone treatment. In stomata resistance, Sangnambatbyeo was decreased stomata resistance on 1 hr after ozone treatment. Hangangchalbyeo, Sangnambatbyeo and Baekna were decreased stomata resistiance on 24 hr after ozone treatment except Ilpumbyeo.