• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.47-54
• /
• 1993

This paper describes briefly the effect of ultrasonic fuel supply device on the performance of four stroke cycle gasoline engine. Experiments were carried out to clarify the effect of ultrasonic fuel supply device on the engine output, traveling fuel consumption ratio, exhaust emissions. The results were obtained as follows: 1.Engine output was increased 9-14% in comparison with that of the conventional injector. 2.Travelling fuel consumption ratio was improved 17-29% in comparison with that of the conventional injector. 3. CO, HC exhaust emissions was decreased compared to the value of the conventional injector. 4.Fuel consumption ratio in highway driving test was improved about 10% in comparison with that of the conventional injector.

• ETRI Journal
• /
• v.39 no.6
• /
• pp.771-781
• /
• 2017

For efficient spectral utilization of satellite channels, a shared band transmission technique is introduced in this paper. A satellite transmits multiple received signals from a gateway and terminal in the common frequency band by superimposing the signals. To improve the power efficiency as well as the spectral efficiency, a travelling wave tube amplifier in the satellite should operate near the saturation level. This causes a nonlinear distortion of the superimposed transmit signal. Without mitigating this nonlinear effect, the self-interference cannot be properly cancelled and the desired signal cannot be demodulated. Therefore, an adaptive compensation scheme for nonlinearity is herein proposed with the proper operation scenario. It is shown through simulations that the proposed shared band transmission approach with nonlinear compensation and self-interference cancellation can achieve an acceptable system performance in nonlinear satellite channels.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.777-782
• /
• 2005

In this paper, we designed and fabricated a partial discharge (PD) detector to diagnose the soundness of CNCV cables by analyzing PD pulses and to predict discharge locations. The PD detector is consisted of a coupling network with a discharge free capacitor and a detection impedance, a voltage follower and a low noise amplifier. Lower cut-off frequency of the detector is adjusted at 175kHz to block AC voltage and to pass discharge pulse only. The discharge location could be obtained by the time of arrival method using travelling wave propagation theory. In a laboratory test on an eighty meter CV cable, we could position the discharge location within a two meter error.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.1888-1894
• /
• 2009

This paper performs TDR real test for measurement of propagation velocity on #1 Pole of HVDC submarine cable section between Jeju and Haenam, and then measured velocity is compared with theoretical value and velocity provided from manufacturer. The measured velocity is also validated from theoretical process based on CIGRE simplified approach. In this paper, the fault location algorithm using multi-scale correlation of SWT(stationary wavelet transform) and travelling wave is additionally proposed for HVDC submarine cable system, it includes fault signal filter for noise cancellation. Finally, the measured velocity is validated from proposed fault location algorithm test once more.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.6 no.3
• /
• pp.281-289
• /
• 1994

An equation set of nonlinear model for regular/irregular waves presented in this study can be applied to waves travelling from deep water to shallow water, which is different from the Boussinesq equations. The presented equations completely satisfy the linear dispersion relationship and when expanded, they are proven to be consistent with the Boussinesq equation of several types. In addition, the position of averaged velocity below the still water level is estimated based on the linear wave theory.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.304-307
• /
• 2003

In this paper, stacked piezoelectric ceramics were used for obtaining a large vibration for a small ultrasonic motor which is useable for the both linear drive and rotational drive. We studied this motor through the finite element analysis method and the simulated driving characteristics were presented. As results, the displacement of the tip of the stator was increased when the layers of the ceramics were increased. Also, by inserting additional aluminum plates between the ceramics and the aluminum bar, the displacement were amplified. In this model, two voltages which have 90 degree phase difference were applied for the bi-directional movement.

• Korean Journal of Optics and Photonics
• /
• v.11 no.3
• /
• pp.166-170
• /
• 2000

A wavelength tunable all-optical clock recovery using a semiconductor optical amplifier in a fiber ring cavity is proposed and demonstrated at the wavelength of 1530 nm to 1570 nm. A synchronized optical pulse train is recovered from 10 Gbps and 30 Gbps randomly generated optical pulse streams with injection locking technique. Also, the system responses to the perturbation and the input average power variation are analyzed by a large-signal model based on time-domain travelling wave equation. ation.

• Aerospace Engineering and Technology
• /
• v.7 no.1
• /
• pp.108-114
• /
• 2008

The aim of this analysis is to verify the electrical compatibility of the interfaces which exist between TWTA(Travelling Wave Tube Amplifier) which is equipment of the Ka-band payload in COMS (Communication, Ocean and Meteorological Satellite) and external equipments. For each interface, this study checked the compatibility between equipments for the power links, commands, digital telemetry, analog telemetry, and failure condition or AIT(Assembly, Integration and Test) errors. In addition with this interface compatibility verification, this study outputs electrical and manufacturing recommendations to be applied at harness level.

• Structural Engineering and Mechanics
• /
• v.35 no.3
• /
• pp.365-377
• /
• 2010

In the present article, effect of non-uniform excitation due to spatially variation of seismic input on nonlinear response of concrete gravity dams is considered. The reservoir is assumed compressible. Isotropic damage mechanics approach is used to model static and dynamic nonlinear behavior of mass concrete in 2D space. The validity of utilized nonlinear model is considered using available theoretical results under static and dynamic conditions. The tallest monolith of Pine Flat dam is selected as a case study. Two cases are analyzed for considering the effect of limited wave propagation velocity on seismic behavior of the dam-reservoir system in which travelling velocities are chosen as 2000 m/s and infinity. It is found that tensile damage in neck and toe regions and also, in the vicinity of the base increase when the system is excited non-uniformly.

• Journal of Magnetics
• /
• v.18 no.3
• /
• pp.255-259
• /
• 2013

In this paper a new coupling method for efficient and simple analysis of single phase induction motor is presented. The circuit representation of both the stator winding and each conducting rotor loop (composed of rotor bar and end ring segment) is used in conjunction with the distribution of magnetic flux linkage instead of inductance matrix. The flux linkage is calculated using air-gap flux density distributions driven by unit currents in the stator windings and rotor bars. The field distribution of one turn of a coil is calculated by FEM and the result is used to calculate total flux linkage by employing a coordinate transformation. The numerical results give good agreement with prior literature. The method is particularly effective in analyzing the effect of the number of rotor bars.