• Journal of Aerospace System Engineering
• /
• v.13 no.2
• /
• pp.51-59
• /
• 2019

Subsequently, Part I [1], which was about the single-cell model, a composite thin-walled beam with a multi-cell of chord-wise asymmetric cross-section, was selected in this study. Moreover, the theoretical dynamic characteristics of the model were analyzed. For this analysis, mathematical modeling was performed by considering the warping restraint effects, transverse shear effects, taper ratio and cross-section ratio. Similar to part I, the mass, stiffness coefficients and Eigen frequencies of the multi-cell section considered were investigated. In particular, the comparison between the multi-cell and single-cell sections and the effects of the cross-section ratio and taper ratio of the model on the Eigen frequencies were analyzed. However, the results compared when the asymmetry of the section was considered and warping function were not corrected.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.3
• /
• pp.421-425
• /
• 2018

The icebreaking research vessel ARAON performed ice field tests during her 2016 Arctic voyage. The ship is subjected to ice loads through ice-ship interaction processes. Local ice load acting on ARAON's bow section was measured by using stain gauges installed on the inner hull plates and transverse frames of bow section. In this paper the local ice loads at transverse frames estimated from shear strain data were compared to ice loads from hull plate pressures by using the influence coefficient method. In addition to the analysis of local ice loads, the characteristics of peak ice loads with the ship speed is also discussed. It is recommended that the local ice loads estimated by calculating shear forces acting on transverse frames may be useful in estimating local ice loads on the hull of ship.

• Steel and Composite Structures
• /
• v.22 no.4
• /
• pp.837-853
• /
• 2016

This paper presents the experimental and numerical study on the distribution of transverse and longitudinal residual stresses in cold-formed thick-walled structural steel rectangular hollow sections manufactured by indirect technique. Hole-drilling method is employed to measure the magnitude of the transverse and longitudinal surface residual stress distribution, and the effects of the residual stresses are evaluated qualitatively by sectioning method. It is shown that compared to normal cold-formed thin-walled structural hollow sections (SHS), the cold-formed thick-walled SHS has similar level of residual stress in the flat area but higher residual stresses in the corner and welding areas. Both the transverse and longitudinal residual stresses tend to open the section. In order to predict the surface residual stresses in the corners of the cold-formed thick-walled SHS, an analytical model is developed. 2D finite element simulation of the cold bending process is conducted to validate the analytical approach. It is shown that in analyzing bending for thick-walled sections, shifting of neutral axis must be considered, since it would lead to nonlinear and non-symmetrical distribution of stresses through the thickness. This phenomenon leads to the fact that cold-formed thick-walled SHSs has different distribution and magnitude of the residual stresses from the cold-formed thin-walled SHSs.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.5
• /
• pp.563-574
• /
• 2020

Currently, road tunnels and railroad tunnels are building smoke control systems to emit toxic gases and smoke from fires. Among the various smoke control systems, the transverse smoke control system has the disadvantage that air supply or exhaust is performed on only half of the cross-section, rather than air supply or exhaust on the entire cross-section of the tunnel as air is supplied or exhausted by partitioning the wind path. Therefore, this study analyzed the effect of exhaustion through numerical analysis and scaled model tests on the zoning smoke control system, which improved the limitations of the transverse smoke control system. As a result of the scaled model test, the transverse ventilation system exhibited a 25.6% smoke control rate based on the state where no smoke was controled, and zoning smoke control system showed a smoke control rate of 40.8%. In addition, as a result of numerical analysis, it was found that transverse ventilation system did not control fire smoke spreading from the tunnel and continued to spread. On the other hand, zoning smoke control system was found to be smoke controled within a certain section due to the air curtain effect and the flue gas effect.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.31-34
• /
• 2005

An experimental investigation was conducted to examine the hysteric behavior of Ultra-High strength concrete columns for the requirement of ACI provision. Seven 1/3 scaled columns were fabricated to simulate an 1/2 story of actual structural members with the cross section $300\times300mm$ and the shear span ratio 4. The main variables are axial load ratio, configuration and volumetric ratio of transverse reinforcement. It has been found that the behavior of columns was affected by axial load ratio rather than the amount and the configuration of transverse reinforcement. Consequently, to secure the ductile behavior of 100MPa Ultra-High strength concrete columns, ACI provision for the requirement of transverse steel may considered axial level and the detail of transverse reinforcement.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.22 no.4
• /
• pp.17-27
• /
• 1985

In this paper, an approximate calculation method on the transverse strength of oil tankers by use of slop-deflection method os described which considers the effect of shear deflection and varing section in elements and the result of calculation in models and actual ships, is presented. The object of this paper is focused on the development of program which can be used widely regardless strut numbers in transverse frame rings. To examine the reliability of the above method, the results in this paper are compared with the results which are obtained by use of SAP4(Structure Analysis Program) based on finite element method. The application of the Slope-Deflection Method on the transverse strength of oil tankers has the advantage that this method takes less than the other methods in calculation.

• Journal of Plant Biology
• /
• v.36 no.1
• /
• pp.29-34
• /
• 1993

Observation was made on early ontogeny of vascular cambium in the cotyledonary node of Pinus koraiensis seedling in order to clarify the cambial ontogeny of the node which was hardly elongated. In transverse view, the derivatives by the early periclinal divisions at the outer region of the procambial strands differentiated to protophloem with establishing a certain degree of radial seriations. Later, some cells in the central region of the procambial strands begin divide periclinally, eventually the cells, differentiate gradually to the vascular cambium. In tangential view, early procambium is consisted of homogeneous short cells with transverse end walls which are tansformed into the long cells and short cells gradually. The long cells continue intrusive growth and the short cells repeat transverse division. Finally, the long and short cells differentiated to cambial fusiform initials and ray initials respectively. In tangential section, the differentiation pattern of cambial initials resembles that of the stem of Ginkgo biloba. But in transverse view, the characteristics in the origin of vascular cambium of the cotyledonary node resembles that of root. The vascular cambium in cotyledonary node is completed after eleven prophylls were formed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.37-40
• /
• 2004

An experimental study was conducted to investigate the stress-strain behavior of confined concrete columns according to transverse reinforcement volumetric ratio. Uniaxial loading tests of eleven column specimens$(250\times100\times500mm)$ with rectangular section were conducted to study effect of confinement. The main variables in this test are transverse reinforcement volumetric ratio and cross tie arrangement. the results indicate that the strength and the ductility of confined concrete columns are subjected to transverse reinforcement volumetric ration and cross tie arrangement.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.215-218
• /
• 1999

A general structural model, which is an extension of the Vlassov theory, is developed for the analysis of composite rotor blades with elastic couplings. A comprehensive analysis applicable to both thick-and thin-walled composite beams, which can have either open- or closed profile is formulated. The theory accounts for the effects of elastic couplings, shell wall thickness, and transverse shear deformations. A semi-complementary energy functional is used to account for the shear stress distribution in the shell wall. The bending and torsion related warpings and the shear correction factors are obtained in closed form as part of the analysis. The resulting first order shear deformation theory describes the beam kinematics in terms of the axial, flap and lag bending, flap and lag shear, torsion and torsion-warping deformations. The theory is validated against experimental results for various cross-section beams with elastic couplings.

• Computers and Concrete
• /
• v.12 no.4
• /
• pp.519-536
• /
• 2013

This paper presents a mixed formulation frame element with the assumptions of the Timoshenko shear beam theory for displacement field and that accounts for interaction between shear and normal stress at material level. Nonlinear response of the element is obtained by integration of section response, which in turn is obtained by integration of material response. Satisfaction of transverse equilibrium equations at section includes the interaction between concrete and transverse reinforcing steel. A 3d plastic damage model is implemented to describe the hysteretic behavior of concrete. Comparisons with available experimental data on RC structural walls confirm the accuracy of proposed method.